From 6b85c20d46812bdbc062b863261c3e5100e30556 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Tue, 8 May 2018 08:14:56 +0200 Subject: dts: update to v4.17-rc1 Signed-off-by: Sascha Hauer --- dts/Bindings/media/i2c/tda1997x.txt | 178 ++++++++++++++++++++++++++++++++++++ 1 file changed, 178 insertions(+) create mode 100644 dts/Bindings/media/i2c/tda1997x.txt (limited to 'dts/Bindings/media/i2c/tda1997x.txt') diff --git a/dts/Bindings/media/i2c/tda1997x.txt b/dts/Bindings/media/i2c/tda1997x.txt new file mode 100644 index 0000000000..e76167999d --- /dev/null +++ b/dts/Bindings/media/i2c/tda1997x.txt @@ -0,0 +1,178 @@ +Device-Tree bindings for the NXP TDA1997x HDMI receiver + +The TDA19971/73 are HDMI video receivers. + +The TDA19971 Video port output pins can be used as follows: + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4] + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4] + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4] + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2] + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0] + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles) + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles) + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) + +The TDA19973 Video port output pins can be used as follows: + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0] + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0] + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0] + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) + +The Video port output pins are mapped via 4-bit 'pin groups' allowing +for a variety of connection possibilities including swapping pin order within +pin groups. The video_portcfg device-tree property consists of register mapping +pairs which map a chip-specific VP output register to a 4-bit pin group. If +the pin group needs to be bit-swapped you can use the *_S pin-group defines. + +Required Properties: + - compatible : + - "nxp,tda19971" for the TDA19971 + - "nxp,tda19973" for the TDA19973 + - reg : I2C slave address + - interrupts : The interrupt number + - DOVDD-supply : Digital I/O supply + - DVDD-supply : Digital Core supply + - AVDD-supply : Analog supply + - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups. + +Optional Properties: + - nxp,audout-format : DAI bus format: "i2s" or "spdif". + - nxp,audout-width : width of audio output data bus (1-4). + - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used). + - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec + mclk. + +The port node shall contain one endpoint child node for its digital +output video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Optional Endpoint Properties: + The following three properties are defined in video-interfaces.txt and + are valid for the output parallel bus endpoint: + - hsync-active: Horizontal synchronization polarity. Defaults to active high. + - vsync-active: Vertical synchronization polarity. Defaults to active high. + - data-active: Data polarity. Defaults to active high. + +Examples: + - VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422 + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) + hdmi-receiver@48 { + compatible = "nxp,tda19971"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tda1997x>; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + DOVDD-supply = <®_3p3v>; + AVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p8v>; + /* audio */ + #sound-dai-cells = <0>; + nxp,audout-format = "i2s"; + nxp,audout-layout = <0>; + nxp,audout-width = <16>; + nxp,audout-mclk-fs = <128>; + /* + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4] + * and Y[11:4] across 16bits in the same pixclk cycle. + */ + nxp,vidout-portcfg = + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >, + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >, + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */ + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >, + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */ + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >; + + port { + tda1997x_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <16>; + hsync-active = <1>; + vsync-active = <1>; + data-active = <1>; + }; + }; + }; + - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656 + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) + hdmi-receiver@48 { + compatible = "nxp,tda19971"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tda1997x>; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + DOVDD-supply = <®_3p3v>; + AVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p8v>; + /* audio */ + #sound-dai-cells = <0>; + nxp,audout-format = "i2s"; + nxp,audout-layout = <0>; + nxp,audout-width = <16>; + nxp,audout-mclk-fs = <128>; + /* + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4] + * and Y[11:4] across 16bits in the same pixclk cycle. + */ + nxp,vidout-portcfg = + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >, + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >, + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */ + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >, + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */ + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >; + + port { + tda1997x_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <16>; + hsync-active = <1>; + vsync-active = <1>; + data-active = <1>; + }; + }; + }; + - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656 + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) + hdmi-receiver@48 { + compatible = "nxp,tda19971"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tda1997x>; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + DOVDD-supply = <®_3p3v>; + AVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p8v>; + /* audio */ + #sound-dai-cells = <0>; + nxp,audout-format = "i2s"; + nxp,audout-layout = <0>; + nxp,audout-width = <16>; + nxp,audout-mclk-fs = <128>; + /* + * The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over + * 2 pixclk cycles. + */ + nxp,vidout-portcfg = + /* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ + < TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >, + /* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ + < TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >, + + port { + tda1997x_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <16>; + hsync-active = <1>; + vsync-active = <1>; + data-active = <1>; + }; + }; + }; -- cgit v1.2.3