From 6940ba22c66ac1c713500027bf5f6832442a1410 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Mon, 19 Aug 2019 08:56:20 +0200 Subject: dts: update to v5.3-rc1 Signed-off-by: Sascha Hauer --- dts/Bindings/net/phy.txt | 80 +----------------------------------------------- 1 file changed, 1 insertion(+), 79 deletions(-) (limited to 'dts/Bindings/net/phy.txt') diff --git a/dts/Bindings/net/phy.txt b/dts/Bindings/net/phy.txt index 9b9e5b1765..2399ee60ca 100644 --- a/dts/Bindings/net/phy.txt +++ b/dts/Bindings/net/phy.txt @@ -1,79 +1 @@ -PHY nodes - -Required properties: - - - interrupts : interrupt specifier for the sole interrupt. - - reg : The ID number for the phy, usually a small integer - -Optional Properties: - -- compatible: Compatible list, may contain - "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for - PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45 - specifications. If neither of these are specified, the default is to - assume clause 22. - - If the PHY reports an incorrect ID (or none at all) then the - "compatible" list may contain an entry with the correct PHY ID in the - form: "ethernet-phy-idAAAA.BBBB" where - AAAA - The value of the 16 bit Phy Identifier 1 register as - 4 hex digits. This is the chip vendor OUI bits 3:18 - BBBB - The value of the 16 bit Phy Identifier 2 register as - 4 hex digits. This is the chip vendor OUI bits 19:24, - followed by 10 bits of a vendor specific ID. - - The compatible list should not contain other values than those - listed here. - -- max-speed: Maximum PHY supported speed (10, 100, 1000...) - -- broken-turn-around: If set, indicates the PHY device does not correctly - release the turn around line low at the end of a MDIO transaction. - -- enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to - compensate for the board being designed with the lanes swapped. - -- enet-phy-lane-no-swap: If set, indicates that PHY will disable swap of the - TX/RX lanes. This property allows the PHY to work correcly after e.g. wrong - bootstrap configuration caused by issues in PCB layout design. - -- eee-broken-100tx: -- eee-broken-1000t: -- eee-broken-10gt: -- eee-broken-1000kx: -- eee-broken-10gkx4: -- eee-broken-10gkr: - Mark the corresponding energy efficient ethernet mode as broken and - request the ethernet to stop advertising it. - -- phy-is-integrated: If set, indicates that the PHY is integrated into the same - physical package as the Ethernet MAC. If needed, muxers should be configured - to ensure the integrated PHY is used. The absence of this property indicates - the muxers should be configured so that the external PHY is used. - -- resets: The reset-controller phandle and specifier for the PHY reset signal. - -- reset-names: Must be "phy" for the PHY reset signal. - -- reset-gpios: The GPIO phandle and specifier for the PHY reset signal. - -- reset-assert-us: Delay after the reset was asserted in microseconds. - If this property is missing the delay will be skipped. - -- reset-deassert-us: Delay after the reset was deasserted in microseconds. - If this property is missing the delay will be skipped. - -Example: - -ethernet-phy@0 { - compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c22"; - interrupt-parent = <&PIC>; - interrupts = <35 IRQ_TYPE_EDGE_RISING>; - reg = <0>; - - resets = <&rst 8>; - reset-names = "phy"; - reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; - reset-assert-us = <1000>; - reset-deassert-us = <2000>; -}; +This file has moved to ethernet-phy.yaml. -- cgit v1.2.3