From bb2de9a333d17bb1b048ad208002501226b83f03 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Tue, 6 Jun 2017 08:07:28 +0200 Subject: dts: update to v4.12-rc1 Signed-off-by: Sascha Hauer --- dts/Bindings/pci/designware-pcie.txt | 26 ++++--- dts/Bindings/pci/faraday,ftpci100.txt | 129 ++++++++++++++++++++++++++++++++++ dts/Bindings/pci/fsl,imx6q-pcie.txt | 14 +++- dts/Bindings/pci/ti-pci.txt | 42 +++++++++-- 4 files changed, 195 insertions(+), 16 deletions(-) create mode 100644 dts/Bindings/pci/faraday,ftpci100.txt (limited to 'dts/Bindings/pci') diff --git a/dts/Bindings/pci/designware-pcie.txt b/dts/Bindings/pci/designware-pcie.txt index 1392c705ce..b2480dd38c 100644 --- a/dts/Bindings/pci/designware-pcie.txt +++ b/dts/Bindings/pci/designware-pcie.txt @@ -6,30 +6,40 @@ Required properties: - reg-names: Must be "config" for the PCIe configuration space. (The old way of getting the configuration address space from "ranges" is deprecated and should be avoided.) +- num-lanes: number of lanes to use +RC mode: - #address-cells: set to <3> - #size-cells: set to <2> - device_type: set to "pci" - ranges: ranges for the PCI memory and I/O regions - #interrupt-cells: set to <1> -- interrupt-map-mask and interrupt-map: standard PCI properties - to define the mapping of the PCIe interface to interrupt +- interrupt-map-mask and interrupt-map: standard PCI + properties to define the mapping of the PCIe interface to interrupt numbers. -- num-lanes: number of lanes to use +EP mode: +- num-ib-windows: number of inbound address translation + windows +- num-ob-windows: number of outbound address translation + windows Optional properties: -- num-viewport: number of view ports configured in hardware. If a platform - does not specify it, the driver assumes 2. - num-lanes: number of lanes to use (this property should be specified unless the link is brought already up in BIOS) - reset-gpio: gpio pin number of power good signal -- bus-range: PCI bus numbers covered (it is recommended for new devicetrees to - specify this property, to keep backwards compatibility a range of 0x00-0xff - is assumed if not present) - clocks: Must contain an entry for each entry in clock-names. See ../clocks/clock-bindings.txt for details. - clock-names: Must include the following entries: - "pcie" - "pcie_bus" +RC mode: +- num-viewport: number of view ports configured in + hardware. If a platform does not specify it, the driver assumes 2. +- bus-range: PCI bus numbers covered (it is recommended + for new devicetrees to specify this property, to keep backwards + compatibility a range of 0x00-0xff is assumed if not present) +EP mode: +- max-functions: maximum number of functions that can be + configured Example configuration: diff --git a/dts/Bindings/pci/faraday,ftpci100.txt b/dts/Bindings/pci/faraday,ftpci100.txt new file mode 100644 index 0000000000..35d4a979bb --- /dev/null +++ b/dts/Bindings/pci/faraday,ftpci100.txt @@ -0,0 +1,129 @@ +Faraday Technology FTPCI100 PCI Host Bridge + +This PCI bridge is found inside that Cortina Systems Gemini SoC platform and +is a generic IP block from Faraday Technology. It exists in two variants: +plain and dual PCI. The plain version embeds a cascading interrupt controller +into the host bridge. The dual version routes the interrupts to the host +chips interrupt controller. + +The host controller appear on the PCI bus with vendor ID 0x159b (Faraday +Technology) and product ID 0x4321. + +Mandatory properties: + +- compatible: ranging from specific to generic, should be one of + "cortina,gemini-pci", "faraday,ftpci100" + "cortina,gemini-pci-dual", "faraday,ftpci100-dual" + "faraday,ftpci100" + "faraday,ftpci100-dual" +- reg: memory base and size for the host bridge +- #address-cells: set to <3> +- #size-cells: set to <2> +- #interrupt-cells: set to <1> +- bus-range: set to <0x00 0xff> +- device_type, set to "pci" +- ranges: see pci.txt +- interrupt-map-mask: see pci.txt +- interrupt-map: see pci.txt +- dma-ranges: three ranges for the inbound memory region. The ranges must + be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, 64MB, + 128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as + pre-fetchable. + +Mandatory subnodes: +- For "faraday,ftpci100" a node representing the interrupt-controller inside the + host bridge is mandatory. It has the following mandatory properties: + - interrupt: see interrupt-controller/interrupts.txt + - interrupt-parent: see interrupt-controller/interrupts.txt + - interrupt-controller: see interrupt-controller/interrupts.txt + - #address-cells: set to <0> + - #interrupt-cells: set to <1> + +I/O space considerations: + +The plain variant has 128MiB of non-prefetchable memory space, whereas the +"dual" variant has 64MiB. Take this into account when describing the ranges. + +Interrupt map considerations: + +The "dual" variant will get INT A, B, C, D from the system interrupt controller +and should point to respective interrupt in that controller in its +interrupt-map. + +The code which is the only documentation of how the Faraday PCI (the non-dual +variant) interrupts assigns the default interrupt mapping/swizzling has +typically been like this, doing the swizzling on the interrupt controller side +rather than in the interconnect: + +interrupt-map-mask = <0xf800 0 0 7>; +interrupt-map = + <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */ + <0x4800 0 0 2 &pci_intc 1>, + <0x4800 0 0 3 &pci_intc 2>, + <0x4800 0 0 4 &pci_intc 3>, + <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */ + <0x5000 0 0 2 &pci_intc 2>, + <0x5000 0 0 3 &pci_intc 3>, + <0x5000 0 0 4 &pci_intc 0>, + <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */ + <0x5800 0 0 2 &pci_intc 3>, + <0x5800 0 0 3 &pci_intc 0>, + <0x5800 0 0 4 &pci_intc 1>, + <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */ + <0x6000 0 0 2 &pci_intc 0>, + <0x6000 0 0 3 &pci_intc 1>, + <0x6000 0 0 4 &pci_intc 2>; + +Example: + +pci@50000000 { + compatible = "cortina,gemini-pci", "faraday,ftpci100"; + reg = <0x50000000 0x100>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>, /* PCI A */ + <26 IRQ_TYPE_LEVEL_HIGH>, /* PCI B */ + <27 IRQ_TYPE_LEVEL_HIGH>, /* PCI C */ + <28 IRQ_TYPE_LEVEL_HIGH>; /* PCI D */ + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + + bus-range = <0x00 0xff>; + ranges = /* 1MiB I/O space 0x50000000-0x500fffff */ + <0x01000000 0 0 0x50000000 0 0x00100000>, + /* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */ + <0x02000000 0 0x58000000 0x58000000 0 0x08000000>; + + /* DMA ranges */ + dma-ranges = + /* 128MiB at 0x00000000-0x07ffffff */ + <0x02000000 0 0x00000000 0x00000000 0 0x08000000>, + /* 64MiB at 0x00000000-0x03ffffff */ + <0x02000000 0 0x00000000 0x00000000 0 0x04000000>, + /* 64MiB at 0x00000000-0x03ffffff */ + <0x02000000 0 0x00000000 0x00000000 0 0x04000000>; + + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */ + <0x4800 0 0 2 &pci_intc 1>, + <0x4800 0 0 3 &pci_intc 2>, + <0x4800 0 0 4 &pci_intc 3>, + <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */ + <0x5000 0 0 2 &pci_intc 2>, + <0x5000 0 0 3 &pci_intc 3>, + <0x5000 0 0 4 &pci_intc 0>, + <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */ + <0x5800 0 0 2 &pci_intc 3>, + <0x5800 0 0 3 &pci_intc 0>, + <0x5800 0 0 4 &pci_intc 1>, + <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */ + <0x6000 0 0 2 &pci_intc 0>, + <0x6000 0 0 3 &pci_intc 0>, + <0x6000 0 0 4 &pci_intc 0>; + pci_intc: interrupt-controller { + interrupt-parent = <&intcon>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; +}; diff --git a/dts/Bindings/pci/fsl,imx6q-pcie.txt b/dts/Bindings/pci/fsl,imx6q-pcie.txt index 83aeb1f5a6..e3d5680875 100644 --- a/dts/Bindings/pci/fsl,imx6q-pcie.txt +++ b/dts/Bindings/pci/fsl,imx6q-pcie.txt @@ -4,7 +4,11 @@ This PCIe host controller is based on the Synopsis Designware PCIe IP and thus inherits all the common properties defined in designware-pcie.txt. Required properties: -- compatible: "fsl,imx6q-pcie", "fsl,imx6sx-pcie", "fsl,imx6qp-pcie" +- compatible: + - "fsl,imx6q-pcie" + - "fsl,imx6sx-pcie", + - "fsl,imx6qp-pcie" + - "fsl,imx7d-pcie" - reg: base address and length of the PCIe controller - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. @@ -34,6 +38,14 @@ Additional required properties for imx6sx-pcie: - clock names: Must include the following additional entries: - "pcie_inbound_axi" +Additional required properties for imx7d-pcie: +- power-domains: Must be set to a phandle pointing to PCIE_PHY power domain +- resets: Must contain phandles to PCIe-related reset lines exposed by SRC + IP block +- reset-names: Must contain the following entires: + - "pciephy" + - "apps" + Example: pcie@0x01000000 { diff --git a/dts/Bindings/pci/ti-pci.txt b/dts/Bindings/pci/ti-pci.txt index 60e25161f3..6a07c96227 100644 --- a/dts/Bindings/pci/ti-pci.txt +++ b/dts/Bindings/pci/ti-pci.txt @@ -1,17 +1,22 @@ TI PCI Controllers PCIe Designware Controller - - compatible: Should be "ti,dra7-pcie"" - - reg : Two register ranges as listed in the reg-names property - - reg-names : The first entry must be "ti-conf" for the TI specific registers - The second entry must be "rc-dbics" for the designware pcie - registers - The third entry must be "config" for the PCIe configuration space + - compatible: Should be "ti,dra7-pcie" for RC + Should be "ti,dra7-pcie-ep" for EP - phys : list of PHY specifiers (used by generic PHY framework) - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the number of PHYs as specified in *phys* property. - ti,hwmods : Name of the hwmod associated to the pcie, "pcie", where is the instance number of the pcie from the HW spec. + - num-lanes as specified in ../designware-pcie.txt + +HOST MODE +========= + - reg : Two register ranges as listed in the reg-names property + - reg-names : The first entry must be "ti-conf" for the TI specific registers + The second entry must be "rc-dbics" for the DesignWare PCIe + registers + The third entry must be "config" for the PCIe configuration space - interrupts : Two interrupt entries must be specified. The first one is for main interrupt line and the second for MSI interrupt line. - #address-cells, @@ -19,13 +24,36 @@ PCIe Designware Controller #interrupt-cells, device_type, ranges, - num-lanes, interrupt-map-mask, interrupt-map : as specified in ../designware-pcie.txt +DEVICE MODE +=========== + - reg : Four register ranges as listed in the reg-names property + - reg-names : "ti-conf" for the TI specific registers + "ep_dbics" for the standard configuration registers as + they are locally accessed within the DIF CS space + "ep_dbics2" for the standard configuration registers as + they are locally accessed within the DIF CS2 space + "addr_space" used to map remote RC address space + - interrupts : one interrupt entries must be specified for main interrupt. + - num-ib-windows : number of inbound address translation windows + - num-ob-windows : number of outbound address translation windows + - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument + should contain the register offset within syscon + and the 2nd argument should contain the bit field + for setting the bit to enable unaligned + access. + Optional Property: - gpios : Should be added if a gpio line is required to drive PERST# line +NOTE: Two DT nodes may be added for each PCI controller; one for host +mode and another for device mode. So in order for PCI to +work in host mode, EP mode DT node should be disabled and in order to PCI to +work in EP mode, host mode DT node should be disabled. Host mode and EP +mode are mutually exclusive. + Example: axi { compatible = "simple-bus"; -- cgit v1.2.3