From e4067b75fb6ca83a58b2c342a0b3ee12e1223c4e Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Thu, 21 Jun 2018 13:44:30 +0200 Subject: dts: update to v4.18-rc1 Signed-off-by: Sascha Hauer --- dts/Bindings/powerpc/4xx/emac.txt | 206 -------------------------------------- dts/Bindings/powerpc/4xx/ndfc.txt | 39 -------- dts/Bindings/powerpc/fsl/gtm.txt | 31 ------ 3 files changed, 276 deletions(-) delete mode 100644 dts/Bindings/powerpc/4xx/emac.txt delete mode 100644 dts/Bindings/powerpc/4xx/ndfc.txt delete mode 100644 dts/Bindings/powerpc/fsl/gtm.txt (limited to 'dts/Bindings/powerpc') diff --git a/dts/Bindings/powerpc/4xx/emac.txt b/dts/Bindings/powerpc/4xx/emac.txt deleted file mode 100644 index 44b842b6ca..0000000000 --- a/dts/Bindings/powerpc/4xx/emac.txt +++ /dev/null @@ -1,206 +0,0 @@ - 4xx/Axon EMAC ethernet nodes - - The EMAC ethernet controller in IBM and AMCC 4xx chips, and also - the Axon bridge. To operate this needs to interact with a this - special McMAL DMA controller, and sometimes an RGMII or ZMII - interface. In addition to the nodes and properties described - below, the node for the OPB bus on which the EMAC sits must have a - correct clock-frequency property. - - i) The EMAC node itself - - Required properties: - - device_type : "network" - - - compatible : compatible list, contains 2 entries, first is - "ibm,emac-CHIP" where CHIP is the host ASIC (440gx, - 405gp, Axon) and second is either "ibm,emac" or - "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon", - "ibm,emac4" - - interrupts : - - interrupt-parent : optional, if needed for interrupt mapping - - reg : - - local-mac-address : 6 bytes, MAC address - - mal-device : phandle of the associated McMAL node - - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated - with this EMAC - - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated - with this EMAC - - cell-index : 1 cell, hardware index of the EMAC cell on a given - ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on - each Axon chip) - - max-frame-size : 1 cell, maximum frame size supported in bytes - - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec - operations. - For Axon, 2048 - - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec - operations. - For Axon, 2048. - - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate - thresholds). - For Axon, 0x00000010 - - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds) - in bytes. - For Axon, 0x00000100 (I think ...) - - phy-mode : string, mode of operations of the PHY interface. - Supported values are: "mii", "rmii", "smii", "rgmii", - "tbi", "gmii", rtbi", "sgmii". - For Axon on CAB, it is "rgmii" - - mdio-device : 1 cell, required iff using shared MDIO registers - (440EP). phandle of the EMAC to use to drive the - MDIO lines for the PHY used by this EMAC. - - zmii-device : 1 cell, required iff connected to a ZMII. phandle of - the ZMII device node - - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII - channel or 0xffffffff if ZMII is only used for MDIO. - - rgmii-device : 1 cell, required iff connected to an RGMII. phandle - of the RGMII device node. - For Axon: phandle of plb5/plb4/opb/rgmii - - rgmii-channel : 1 cell, required iff connected to an RGMII. Which - RGMII channel is used by this EMAC. - Fox Axon: present, whatever value is appropriate for each - EMAC, that is the content of the current (bogus) "phy-port" - property. - - Optional properties: - - phy-address : 1 cell, optional, MDIO address of the PHY. If absent, - a search is performed. - - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY - for, used if phy-address is absent. bit 0x00000001 is - MDIO address 0. - For Axon it can be absent, though my current driver - doesn't handle phy-address yet so for now, keep - 0x00ffffff in it. - - phy-handle : Used to describe configurations where a external PHY - is used. Please refer to: - Documentation/devicetree/bindings/net/ethernet.txt - - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec - operations (if absent the value is the same as - rx-fifo-size). For Axon, either absent or 2048. - - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec - operations (if absent the value is the same as - tx-fifo-size). For Axon, either absent or 2048. - - tah-device : 1 cell, optional. If connected to a TAH engine for - offload, phandle of the TAH device node. - - tah-channel : 1 cell, optional. If appropriate, channel used on the - TAH engine. - - fixed-link : Fixed-link subnode describing a link to a non-MDIO - managed entity. See - Documentation/devicetree/bindings/net/fixed-link.txt - for details. - - mdio subnode : When the EMAC has a phy connected to its local - mdio, which us supported by the kernel's network - PHY library in drivers/net/phy, there must be device - tree subnode with the following required properties: - - #address-cells: Must be <1>. - - #size-cells: Must be <0>. - - For PHY definitions: Please refer to - Documentation/devicetree/bindings/net/phy.txt and - Documentation/devicetree/bindings/net/ethernet.txt - - Examples: - - EMAC0: ethernet@40000800 { - device_type = "network"; - compatible = "ibm,emac-440gp", "ibm,emac"; - interrupt-parent = <&UIC1>; - interrupts = <1c 4 1d 4>; - reg = <40000800 70>; - local-mac-address = [00 04 AC E3 1B 1E]; - mal-device = <&MAL0>; - mal-tx-channel = <0 1>; - mal-rx-channel = <0>; - cell-index = <0>; - max-frame-size = <5dc>; - rx-fifo-size = <1000>; - tx-fifo-size = <800>; - phy-mode = "rmii"; - phy-map = <00000001>; - zmii-device = <&ZMII0>; - zmii-channel = <0>; - }; - - EMAC1: ethernet@ef600c00 { - device_type = "network"; - compatible = "ibm,emac-apm821xx", "ibm,emac4sync"; - interrupt-parent = <&EMAC1>; - interrupts = <0 1>; - #interrupt-cells = <1>; - #address-cells = <0>; - #size-cells = <0>; - interrupt-map = <0 &UIC2 0x10 IRQ_TYPE_LEVEL_HIGH /* Status */ - 1 &UIC2 0x14 IRQ_TYPE_LEVEL_HIGH /* Wake */>; - reg = <0xef600c00 0x000000c4>; - local-mac-address = [000000000000]; /* Filled in by U-Boot */ - mal-device = <&MAL0>; - mal-tx-channel = <0>; - mal-rx-channel = <0>; - cell-index = <0>; - max-frame-size = <9000>; - rx-fifo-size = <16384>; - tx-fifo-size = <2048>; - fifo-entry-size = <10>; - phy-mode = "rgmii"; - phy-handle = <&phy0>; - phy-map = <0x00000000>; - rgmii-device = <&RGMII0>; - rgmii-channel = <0>; - tah-device = <&TAH0>; - tah-channel = <0>; - has-inverted-stacr-oc; - has-new-stacr-staopc; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - phy0: ethernet-phy@0 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <0>; - }; - }; - }; - - - ii) McMAL node - - Required properties: - - device_type : "dma-controller" - - compatible : compatible list, containing 2 entries, first is - "ibm,mcmal-CHIP" where CHIP is the host ASIC (like - emac) and the second is either "ibm,mcmal" or - "ibm,mcmal2". - For Axon, "ibm,mcmal-axon","ibm,mcmal2" - - interrupts : . - For Axon: This is _different_ from the current - firmware. We use the "delayed" interrupts for txeob - and rxeob. Thus we end up with mapping those 5 MPIC - interrupts, all level positive sensitive: 10, 11, 32, - 33, 34 (in decimal) - - dcr-reg : < DCR registers range > - - dcr-parent : if needed for dcr-reg - - num-tx-chans : 1 cell, number of Tx channels - - num-rx-chans : 1 cell, number of Rx channels - - iii) ZMII node - - Required properties: - - compatible : compatible list, containing 2 entries, first is - "ibm,zmii-CHIP" where CHIP is the host ASIC (like - EMAC) and the second is "ibm,zmii". - For Axon, there is no ZMII node. - - reg : - - iv) RGMII node - - Required properties: - - compatible : compatible list, containing 2 entries, first is - "ibm,rgmii-CHIP" where CHIP is the host ASIC (like - EMAC) and the second is "ibm,rgmii". - For Axon, "ibm,rgmii-axon","ibm,rgmii" - - reg : - - revision : as provided by the RGMII new version register if - available. - For Axon: 0x0000012a diff --git a/dts/Bindings/powerpc/4xx/ndfc.txt b/dts/Bindings/powerpc/4xx/ndfc.txt deleted file mode 100644 index 869f0b5f16..0000000000 --- a/dts/Bindings/powerpc/4xx/ndfc.txt +++ /dev/null @@ -1,39 +0,0 @@ -AMCC NDFC (NanD Flash Controller) - -Required properties: -- compatible : "ibm,ndfc". -- reg : should specify chip select and size used for the chip (0x2000). - -Optional properties: -- ccr : NDFC config and control register value (default 0). -- bank-settings : NDFC bank configuration register value (default 0). - -Notes: -- partition(s) - follows the OF MTD standard for partitions - -Example: - -ndfc@1,0 { - compatible = "ibm,ndfc"; - reg = <0x00000001 0x00000000 0x00002000>; - ccr = <0x00001000>; - bank-settings = <0x80002222>; - #address-cells = <1>; - #size-cells = <1>; - - nand { - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "kernel"; - reg = <0x00000000 0x00200000>; - }; - partition@200000 { - label = "root"; - reg = <0x00200000 0x03E00000>; - }; - }; -}; - - diff --git a/dts/Bindings/powerpc/fsl/gtm.txt b/dts/Bindings/powerpc/fsl/gtm.txt deleted file mode 100644 index 9a33efded4..0000000000 --- a/dts/Bindings/powerpc/fsl/gtm.txt +++ /dev/null @@ -1,31 +0,0 @@ -* Freescale General-purpose Timers Module - -Required properties: - - compatible : should be - "fsl,-gtm", "fsl,gtm" for SOC GTMs - "fsl,-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs - "fsl,-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs - - reg : should contain gtm registers location and length (0x40). - - interrupts : should contain four interrupts. - - interrupt-parent : interrupt source phandle. - - clock-frequency : specifies the frequency driving the timer. - -Example: - -timer@500 { - compatible = "fsl,mpc8360-gtm", "fsl,gtm"; - reg = <0x500 0x40>; - interrupts = <90 8 78 8 84 8 72 8>; - interrupt-parent = <&ipic>; - /* filled by u-boot */ - clock-frequency = <0>; -}; - -timer@440 { - compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm"; - reg = <0x440 0x40>; - interrupts = <12 13 14 15>; - interrupt-parent = <&qeic>; - /* filled by u-boot */ - clock-frequency = <0>; -}; -- cgit v1.2.3