From 6e6d9a2ff045f09d5a03e876becea5e6a1dabe90 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Tue, 8 Dec 2015 07:35:17 +0100 Subject: dts: update to v4.4-rc1 Signed-off-by: Sascha Hauer --- dts/Bindings/sound/ak4554.c | 11 ---- dts/Bindings/sound/ak4554.txt | 11 ++++ dts/Bindings/sound/ak4613.txt | 17 ++++++ dts/Bindings/sound/ak4642.txt | 22 ++++++- dts/Bindings/sound/atmel-classd.txt | 52 +++++++++++++++++ dts/Bindings/sound/da7213.txt | 41 +++++++++++++ dts/Bindings/sound/da7219.txt | 106 ++++++++++++++++++++++++++++++++++ dts/Bindings/sound/fsl-asoc-card.txt | 10 ++-- dts/Bindings/sound/nau8825.txt | 102 ++++++++++++++++++++++++++++++++ dts/Bindings/sound/renesas,rsnd.txt | 7 +++ dts/Bindings/sound/rockchip-i2s.txt | 6 +- dts/Bindings/sound/rockchip-spdif.txt | 40 +++++++++++++ dts/Bindings/sound/rt5640.txt | 9 ++- dts/Bindings/sound/sun4i-codec.txt | 27 +++++++++ dts/Bindings/sound/tdm-slot.txt | 11 +++- 15 files changed, 448 insertions(+), 24 deletions(-) delete mode 100644 dts/Bindings/sound/ak4554.c create mode 100644 dts/Bindings/sound/ak4554.txt create mode 100644 dts/Bindings/sound/ak4613.txt create mode 100644 dts/Bindings/sound/atmel-classd.txt create mode 100644 dts/Bindings/sound/da7213.txt create mode 100644 dts/Bindings/sound/da7219.txt create mode 100644 dts/Bindings/sound/nau8825.txt create mode 100644 dts/Bindings/sound/rockchip-spdif.txt create mode 100644 dts/Bindings/sound/sun4i-codec.txt (limited to 'dts/Bindings/sound') diff --git a/dts/Bindings/sound/ak4554.c b/dts/Bindings/sound/ak4554.c deleted file mode 100644 index 934fa02754..0000000000 --- a/dts/Bindings/sound/ak4554.c +++ /dev/null @@ -1,11 +0,0 @@ -AK4554 ADC/DAC - -Required properties: - - - compatible : "asahi-kasei,ak4554" - -Example: - -ak4554-adc-dac { - compatible = "asahi-kasei,ak4554"; -}; diff --git a/dts/Bindings/sound/ak4554.txt b/dts/Bindings/sound/ak4554.txt new file mode 100644 index 0000000000..934fa02754 --- /dev/null +++ b/dts/Bindings/sound/ak4554.txt @@ -0,0 +1,11 @@ +AK4554 ADC/DAC + +Required properties: + + - compatible : "asahi-kasei,ak4554" + +Example: + +ak4554-adc-dac { + compatible = "asahi-kasei,ak4554"; +}; diff --git a/dts/Bindings/sound/ak4613.txt b/dts/Bindings/sound/ak4613.txt new file mode 100644 index 0000000000..15a919522b --- /dev/null +++ b/dts/Bindings/sound/ak4613.txt @@ -0,0 +1,17 @@ +AK4613 I2C transmitter + +This device supports I2C mode only. + +Required properties: + +- compatible : "asahi-kasei,ak4613" +- reg : The chip select number on the I2C bus + +Example: + +&i2c { + ak4613: ak4613@0x10 { + compatible = "asahi-kasei,ak4613"; + reg = <0x10>; + }; +}; diff --git a/dts/Bindings/sound/ak4642.txt b/dts/Bindings/sound/ak4642.txt index 623d4e70ae..340784db68 100644 --- a/dts/Bindings/sound/ak4642.txt +++ b/dts/Bindings/sound/ak4642.txt @@ -7,7 +7,14 @@ Required properties: - compatible : "asahi-kasei,ak4642" or "asahi-kasei,ak4643" or "asahi-kasei,ak4648" - reg : The chip select number on the I2C bus -Example: +Optional properties: + + - #clock-cells : common clock binding; shall be set to 0 + - clocks : common clock binding; MCKI clock + - clock-frequency : common clock binding; frequency of MCKO + - clock-output-names : common clock binding; MCKO clock name + +Example 1: &i2c { ak4648: ak4648@0x12 { @@ -15,3 +22,16 @@ Example: reg = <0x12>; }; }; + +Example 2: + +&i2c { + ak4643: codec@12 { + compatible = "asahi-kasei,ak4643"; + reg = <0x12>; + #clock-cells = <0>; + clocks = <&audio_clock>; + clock-frequency = <12288000>; + clock-output-names = "ak4643_mcko"; + }; +}; diff --git a/dts/Bindings/sound/atmel-classd.txt b/dts/Bindings/sound/atmel-classd.txt new file mode 100644 index 0000000000..0018451c43 --- /dev/null +++ b/dts/Bindings/sound/atmel-classd.txt @@ -0,0 +1,52 @@ +* Atmel ClassD driver under ALSA SoC architecture + +Required properties: +- compatible + Should be "atmel,sama5d2-classd". +- reg + Should contain ClassD registers location and length. +- interrupts + Should contain the IRQ line for the ClassD. +- dmas + One DMA specifiers as described in atmel-dma.txt and dma.txt files. +- dma-names + Must be "tx". +- clock-names + Tuple listing input clock names. + Required elements: "pclk", "gclk" and "aclk". +- clocks + Please refer to clock-bindings.txt. + +Optional properties: +- pinctrl-names, pinctrl-0 + Please refer to pinctrl-bindings.txt. +- atmel,model + The user-visible name of this sound complex. + The default value is "CLASSD". +- atmel,pwm-type + PWM modulation type, "single" or "diff". + The default value is "single". +- atmel,non-overlap-time + Set non-overlapping time, the unit is nanosecond(ns). + There are four values, + <5>, <10>, <15>, <20>, the default value is <10>. + Non-overlapping will be disabled if not specified. + +Example: +classd: classd@fc048000 { + compatible = "atmel,sama5d2-classd"; + reg = <0xfc048000 0x100>; + interrupts = <59 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(47))>; + dma-names = "tx"; + clocks = <&classd_clk>, <&classd_gclk>, <&audio_pll_pmc>; + clock-names = "pclk", "gclk", "aclk"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_classd_default>; + atmel,model = "classd @ SAMA5D2-Xplained"; + atmel,pwm-type = "diff"; + atmel,non-overlap-time = <10>; +}; diff --git a/dts/Bindings/sound/da7213.txt b/dts/Bindings/sound/da7213.txt new file mode 100644 index 0000000000..58902802d5 --- /dev/null +++ b/dts/Bindings/sound/da7213.txt @@ -0,0 +1,41 @@ +Dialog Semiconductor DA7213 Audio Codec bindings + +====== + +Required properties: +- compatible : Should be "dlg,da7213" +- reg: Specifies the I2C slave address + +Optional properties: +- clocks : phandle and clock specifier for codec MCLK. +- clock-names : Clock name string for 'clocks' attribute, should be "mclk". + +- dlg,micbias1-lvl : Voltage (mV) for Mic Bias 1 + [<1600>, <2200>, <2500>, <3000>] +- dlg,micbias2-lvl : Voltage (mV) for Mic Bias 2 + [<1600>, <2200>, <2500>, <3000>] +- dlg,dmic-data-sel : DMIC channel select based on clock edge. + ["lrise_rfall", "lfall_rrise"] +- dlg,dmic-samplephase : When to sample audio from DMIC. + ["on_clkedge", "between_clkedge"] +- dlg,dmic-clkrate : DMIC clock frequency (Hz). + [<1500000>, <3000000>] + +====== + +Example: + + codec_i2c: da7213@1a { + compatible = "dlg,da7213"; + reg = <0x1a>; + + clocks = <&clks 201>; + clock-names = "mclk"; + + dlg,micbias1-lvl = <2500>; + dlg,micbias2-lvl = <2500>; + + dlg,dmic-data-sel = "lrise_rfall"; + dlg,dmic-samplephase = "between_clkedge"; + dlg,dmic-clkrate = <3000000>; + }; diff --git a/dts/Bindings/sound/da7219.txt b/dts/Bindings/sound/da7219.txt new file mode 100644 index 0000000000..1b7030911a --- /dev/null +++ b/dts/Bindings/sound/da7219.txt @@ -0,0 +1,106 @@ +Dialog Semiconductor DA7219 Audio Codec bindings + +DA7219 is an audio codec with advanced accessory detect features. + +====== + +Required properties: +- compatible : Should be "dlg,da7219" +- reg: Specifies the I2C slave address + +- interrupt-parent : Specifies the phandle of the interrupt controller to which + the IRQs from DA7219 are delivered to. +- interrupts : IRQ line info for DA7219. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for + further information relating to interrupt properties) + +- VDD-supply: VDD power supply for the device +- VDDMIC-supply: VDDMIC power supply for the device +- VDDIO-supply: VDDIO power supply for the device + (See Documentation/devicetree/bindings/regulator/regulator.txt for further + information relating to regulators) + +Optional properties: +- interrupt-names : Name associated with interrupt line. Should be "wakeup" if + interrupt is to be used to wake system, otherwise "irq" should be used. +- wakeup-source: Flag to indicate this device can wake system (suspend/resume). + +- clocks : phandle and clock specifier for codec MCLK. +- clock-names : Clock name string for 'clocks' attribute, should be "mclk". + +- dlg,ldo-lvl : Required internal LDO voltage (mV) level for digital engine + [<1050>, <1100>, <1200>, <1400>] +- dlg,micbias-lvl : Voltage (mV) for Mic Bias + [<1800>, <2000>, <2200>, <2400>, <2600>] +- dlg,mic-amp-in-sel : Mic input source type + ["diff", "se_p", "se_n"] + +====== + +Child node - 'da7219_aad': + +Optional properties: +- dlg,micbias-pulse-lvl : Mic bias higher voltage pulse level (mV). + [<2800>, <2900>] +- dlg,micbias-pulse-time : Mic bias higher voltage pulse duration (ms) +- dlg,btn-cfg : Periodic button press measurements for 4-pole jack (ms) + [<2>, <5>, <10>, <50>, <100>, <200>, <500>] +- dlg,mic-det-thr : Impedance threshold for mic detection measurement (Ohms) + [<200>, <500>, <750>, <1000>] +- dlg,jack-ins-deb : Debounce time for jack insertion (ms) + [<5>, <10>, <20>, <50>, <100>, <200>, <500>, <1000>] +- dlg,jack-det-rate: Jack type detection latency (3/4 pole) + ["32ms_64ms", "64ms_128ms", "128ms_256ms", "256ms_512ms"] +- dlg,jack-rem-deb : Debounce time for jack removal (ms) + [<1>, <5>, <10>, <20>] +- dlg,a-d-btn-thr : Impedance threshold between buttons A and D + [0x0 - 0xFF] +- dlg,d-b-btn-thr : Impedance threshold between buttons D and B + [0x0 - 0xFF] +- dlg,b-c-btn-thr : Impedance threshold between buttons B and C + [0x0 - 0xFF] +- dlg,c-mic-btn-thr : Impedance threshold between button C and Mic + [0x0 - 0xFF] +- dlg,btn-avg : Number of 8-bit readings for averaged button measurement + [<1>, <2>, <4>, <8>] +- dlg,adc-1bit-rpt : Repeat count for 1-bit button measurement + [<1>, <2>, <4>, <8>] + +====== + +Example: + + codec: da7219@1a { + compatible = "dlg,da7219"; + reg = <0x1a>; + + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; + + VDD-supply = <®_audio>; + VDDMIC-supply = <®_audio>; + VDDIO-supply = <®_audio>; + + clocks = <&clks 201>; + clock-names = "mclk"; + + dlg,ldo-lvl = <1200>; + dlg,micbias-lvl = <2600>; + dlg,mic-amp-in-sel = "diff"; + + da7219_aad { + dlg,btn-cfg = <50>; + dlg,mic-det-thr = <500>; + dlg,jack-ins-deb = <20>; + dlg,jack-det-rate = "32ms_64ms"; + dlg,jack-rem-deb = <1>; + + dlg,a-d-btn-thr = <0xa>; + dlg,d-b-btn-thr = <0x16>; + dlg,b-c-btn-thr = <0x21>; + dlg,c-mic-btn-thr = <0x3E>; + + dlg,btn-avg = <4>; + dlg,adc-1bit-rpt = <1>; + }; + }; diff --git a/dts/Bindings/sound/fsl-asoc-card.txt b/dts/Bindings/sound/fsl-asoc-card.txt index a96774c194..ce55c0a6f7 100644 --- a/dts/Bindings/sound/fsl-asoc-card.txt +++ b/dts/Bindings/sound/fsl-asoc-card.txt @@ -13,13 +13,15 @@ So having this generic sound card allows all Freescale SoC users to benefit from the simplification of a new card support and the capability of the wide sample rates support through ASRC. -Note: The card is initially designed for those sound cards who use I2S and - PCM DAI formats. However, it'll be also possible to support those non - I2S/PCM type sound cards, such as S/PDIF audio and HDMI audio, as long - as the driver has been properly upgraded. +Note: The card is initially designed for those sound cards who use AC'97, I2S + and PCM DAI formats. However, it'll be also possible to support those non + AC'97/I2S/PCM type sound cards, such as S/PDIF audio and HDMI audio, as + long as the driver has been properly upgraded. The compatible list for this generic sound card currently: + "fsl,imx-audio-ac97" + "fsl,imx-audio-cs42888" "fsl,imx-audio-wm8962" diff --git a/dts/Bindings/sound/nau8825.txt b/dts/Bindings/sound/nau8825.txt new file mode 100644 index 0000000000..d3374231c8 --- /dev/null +++ b/dts/Bindings/sound/nau8825.txt @@ -0,0 +1,102 @@ +Nuvoton NAU8825 audio codec + +This device supports I2C only. + +Required properties: + - compatible : Must be "nuvoton,nau8825" + + - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1). + +Optional properties: + - nuvoton,jkdet-enable: Enable jack detection via JKDET pin. + - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled, + otherwise pin in high impedance state. + - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down. + - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low. + + - nuvoton,vref-impedance: VREF Impedance selection + 0 - Open + 1 - 25 kOhm + 2 - 125 kOhm + 3 - 2.5 kOhm + + - nuvoton,micbias-voltage: Micbias voltage level. + 0 - VDDA + 1 - VDDA + 2 - VDDA * 1.1 + 3 - VDDA * 1.2 + 4 - VDDA * 1.3 + 5 - VDDA * 1.4 + 6 - VDDA * 1.53 + 7 - VDDA * 1.53 + + - nuvoton,sar-threshold-num: Number of buttons supported + - nuvoton,sar-threshold: Impedance threshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated as + SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R) + where MICBIAS is configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by 'nuvoton,sar-voltage', R - button impedance. + Refer datasheet section 10.2 for more information about threshold calculation. + + - nuvoton,sar-hysteresis: Button impedance measurement hysteresis. + + - nuvoton,sar-voltage: Reference voltage for button impedance measurement. + 0 - VDDA + 1 - VDDA + 2 - VDDA * 1.1 + 3 - VDDA * 1.2 + 4 - VDDA * 1.3 + 5 - VDDA * 1.4 + 6 - VDDA * 1.53 + 7 - VDDA * 1.53 + + - nuvoton,sar-compare-time: SAR compare time + 0 - 500 ns + 1 - 1 us + 2 - 2 us + 3 - 4 us + + - nuvoton,sar-sampling-time: SAR sampling time + 0 - 2 us + 1 - 4 us + 2 - 8 us + 3 - 16 us + + - nuvoton,short-key-debounce: Button short key press debounce time. + 0 - 30 ms + 1 - 50 ms + 2 - 100 ms + 3 - 30 ms + + - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms + - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms + + - clocks: list of phandle and clock specifier pairs according to common clock bindings for the + clocks described in clock-names + - clock-names: should include "mclk" for the MCLK master clock + +Example: + + headset: nau8825@1a { + compatible = "nuvoton,nau8825"; + reg = <0x1a>; + interrupt-parent = <&gpio>; + interrupts = ; + nuvoton,jkdet-enable; + nuvoton,jkdet-pull-enable; + nuvoton,jkdet-pull-up; + nuvoton,jkdet-polarity = ; + nuvoton,vref-impedance = <2>; + nuvoton,micbias-voltage = <6>; + // Setup 4 buttons impedance according to Android specification + nuvoton,sar-threshold-num = <4>; + nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>; + nuvoton,sar-hysteresis = <1>; + nuvoton,sar-voltage = <0>; + nuvoton,sar-compare-time = <0>; + nuvoton,sar-sampling-time = <0>; + nuvoton,short-key-debounce = <2>; + nuvoton,jack-insert-debounce = <7>; + nuvoton,jack-eject-debounce = <7>; + + clock-names = "mclk"; + clocks = <&tegra_car TEGRA210_CLK_CLK_OUT_2>; + }; diff --git a/dts/Bindings/sound/renesas,rsnd.txt b/dts/Bindings/sound/renesas,rsnd.txt index 1173395b5e..c57cbd6573 100644 --- a/dts/Bindings/sound/renesas,rsnd.txt +++ b/dts/Bindings/sound/renesas,rsnd.txt @@ -4,10 +4,12 @@ Required properties: - compatible : "renesas,rcar_sound-", fallbacks "renesas,rcar_sound-gen1" if generation1, and "renesas,rcar_sound-gen2" if generation2 + "renesas,rcar_sound-gen3" if generation3 Examples with soctypes are: - "renesas,rcar_sound-r8a7778" (R-Car M1A) - "renesas,rcar_sound-r8a7790" (R-Car H2) - "renesas,rcar_sound-r8a7791" (R-Car M2-W) + - "renesas,rcar_sound-r8a7795" (R-Car H3) - reg : Should contain the register physical address. required register is SRU/ADG/SSI if generation1 @@ -30,6 +32,11 @@ Required properties: - rcar_sound,dai : DAI contents. The number of DAI subnode should be same as HW. see below for detail. +- #sound-dai-cells : it must be 0 if your system is using single DAI + it must be 1 if your system is using multi DAI +- #clock-cells : it must be 0 if your system has audio_clkout + it must be 1 if your system has audio_clkout0/1/2/3 +- clock-frequency : for all audio_clkout0/1/2/3 SSI subnode properties: - interrupts : Should contain SSI interrupt for PIO transfer diff --git a/dts/Bindings/sound/rockchip-i2s.txt b/dts/Bindings/sound/rockchip-i2s.txt index 9b82c20b30..2267d249ca 100644 --- a/dts/Bindings/sound/rockchip-i2s.txt +++ b/dts/Bindings/sound/rockchip-i2s.txt @@ -12,8 +12,6 @@ Required properties: - reg: physical base address of the controller and length of memory mapped region. - interrupts: should contain the I2S interrupt. -- #address-cells: should be 1. -- #size-cells: should be 0. - dmas: DMA specifiers for tx and rx dma. See the DMA client binding, Documentation/devicetree/bindings/dma/dma.txt - dma-names: should include "tx" and "rx". @@ -21,6 +19,7 @@ Required properties: - clock-names: should contain followings: - "i2s_hclk": clock for I2S BUS - "i2s_clk" : clock for I2S controller +- rockchip,capture-channels: max capture channels, if not set, 2 channels default. Example for rk3288 I2S controller: @@ -28,10 +27,9 @@ i2s@ff890000 { compatible = "rockchip,rk3288-i2s", "rockchip,rk3066-i2s"; reg = <0xff890000 0x10000>; interrupts = ; - #address-cells = <1>; - #size-cells = <0>; dmas = <&pdma1 0>, <&pdma1 1>; dma-names = "tx", "rx"; clock-names = "i2s_hclk", "i2s_clk"; clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>; + rockchip,capture-channels = <2>; }; diff --git a/dts/Bindings/sound/rockchip-spdif.txt b/dts/Bindings/sound/rockchip-spdif.txt new file mode 100644 index 0000000000..e64dbdea7d --- /dev/null +++ b/dts/Bindings/sound/rockchip-spdif.txt @@ -0,0 +1,40 @@ +* Rockchip SPDIF transceiver + +The S/PDIF audio block is a stereo transceiver that allows the +processor to receive and transmit digital audio via an coaxial cable or +a fibre cable. + +Required properties: + +- compatible: should be one of the following: + - "rockchip,rk3288-spdif", "rockchip,rk3188-spdif" or + "rockchip,rk3066-spdif" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: should contain the SPDIF interrupt. +- dmas: DMA specifiers for tx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: should be "tx" +- clocks: a list of phandle + clock-specifier pairs, one for each entry + in clock-names. +- clock-names: should contain following: + - "hclk": clock for SPDIF controller + - "mclk" : clock for SPDIF bus + +Required properties on RK3288: + - rockchip,grf: the phandle of the syscon node for the general register + file (GRF) + +Example for the rk3188 SPDIF controller: + +spdif: spdif@0x1011e000 { + compatible = "rockchip,rk3188-spdif", "rockchip,rk3066-spdif"; + reg = <0x1011e000 0x2000>; + interrupts = ; + dmas = <&dmac1_s 8>; + dma-names = "tx"; + clock-names = "hclk", "mclk"; + clocks = <&cru HCLK_SPDIF>, <&cru SCLK_SPDIF>; + status = "disabled"; + #sound-dai-cells = <0>; +}; diff --git a/dts/Bindings/sound/rt5640.txt b/dts/Bindings/sound/rt5640.txt index bac4d9ac1e..9e62f6eb34 100644 --- a/dts/Bindings/sound/rt5640.txt +++ b/dts/Bindings/sound/rt5640.txt @@ -14,7 +14,8 @@ Optional properties: - realtek,in1-differential - realtek,in2-differential - Boolean. Indicate MIC1/2 input are differential, rather than single-ended. +- realtek,in3-differential + Boolean. Indicate MIC1/2/3 input are differential, rather than single-ended. - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. @@ -24,9 +25,11 @@ Pins on the device (for linking into audio routes) for RT5639/RT5640: * DMIC2 * MICBIAS1 * IN1P - * IN1R + * IN1N * IN2P - * IN2R + * IN2N + * IN3P + * IN3N * HPOL * HPOR * LOUTL diff --git a/dts/Bindings/sound/sun4i-codec.txt b/dts/Bindings/sound/sun4i-codec.txt new file mode 100644 index 0000000000..c92966bd54 --- /dev/null +++ b/dts/Bindings/sound/sun4i-codec.txt @@ -0,0 +1,27 @@ +* Allwinner A10 Codec + +Required properties: +- compatible: must be either "allwinner,sun4i-a10-codec" or + "allwinner,sun7i-a20-codec" +- reg: must contain the registers location and length +- interrupts: must contain the codec interrupt +- dmas: DMA channels for tx and rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: should include "tx" and "rx". +- clocks: a list of phandle + clock-specifer pairs, one for each entry + in clock-names. +- clock-names: should contain followings: + - "apb": the parent APB clock for this controller + - "codec": the parent module clock + +Example: +codec: codec@01c22c00 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun7i-a20-codec"; + reg = <0x01c22c00 0x40>; + interrupts = <0 30 4>; + clocks = <&apb0_gates 0>, <&codec_clk>; + clock-names = "apb", "codec"; + dmas = <&dma 0 19>, <&dma 0 19>; + dma-names = "rx", "tx"; +}; diff --git a/dts/Bindings/sound/tdm-slot.txt b/dts/Bindings/sound/tdm-slot.txt index 6a2c84247f..34cf70e2cb 100644 --- a/dts/Bindings/sound/tdm-slot.txt +++ b/dts/Bindings/sound/tdm-slot.txt @@ -4,11 +4,15 @@ This specifies audio DAI's TDM slot. TDM slot properties: dai-tdm-slot-num : Number of slots in use. -dai-tdm-slot-width : Width in bits for each slot. +dai-tdm-slot-width : Width in bits for each slot. +dai-tdm-slot-tx-mask : Transmit direction slot mask, optional +dai-tdm-slot-rx-mask : Receive direction slot mask, optional For instance: dai-tdm-slot-num = <2>; dai-tdm-slot-width = <8>; + dai-tdm-slot-tx-mask = <0 1>; + dai-tdm-slot-rx-mask = <1 0>; And for each spcified driver, there could be one .of_xlate_tdm_slot_mask() to specify a explicit mapping of the channels and the slots. If it's absent @@ -18,3 +22,8 @@ tx and rx masks. For snd_soc_of_xlate_tdm_slot_mask(), the tx and rx masks will use a 1 bit for an active slot as default, and the default active bits are at the LSB of the masks. + +The explicit masks are given as array of integers, where the first +number presents bit-0 (LSB), second presents bit-1, etc. Any non zero +number is considered 1 and 0 is 0. snd_soc_of_xlate_tdm_slot_mask() +does not do anything, if either mask is set non zero value. -- cgit v1.2.3