From 796af3473b8222bcd89aa63e9886c355a6baf95d Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Wed, 5 Jun 2019 00:06:30 +0200 Subject: dts: update to v5.2-rc1 Signed-off-by: Sascha Hauer --- dts/Bindings/usb/amlogic,dwc3.txt | 88 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 88 insertions(+) (limited to 'dts/Bindings/usb/amlogic,dwc3.txt') diff --git a/dts/Bindings/usb/amlogic,dwc3.txt b/dts/Bindings/usb/amlogic,dwc3.txt index 9a8b631904..b9f04e617e 100644 --- a/dts/Bindings/usb/amlogic,dwc3.txt +++ b/dts/Bindings/usb/amlogic,dwc3.txt @@ -40,3 +40,91 @@ Example device nodes: phy-names = "usb2-phy", "usb3-phy"; }; }; + +Amlogic Meson G12A DWC3 USB SoC Controller Glue + +The Amlogic G12A embeds a DWC3 USB IP Core configured for USB2 and USB3 +in host-only mode, and a DWC2 IP Core configured for USB2 peripheral mode +only. + +A glue connects the DWC3 core to USB2 PHYs and optionnaly to an USB3 PHY. + +One of the USB2 PHY can be re-routed in peripheral mode to a DWC2 USB IP. + +The DWC3 Glue controls the PHY routing and power, an interrupt line is +connected to the Glue to serve as OTG ID change detection. + +Required properties: +- compatible: Should be "amlogic,meson-g12a-usb-ctrl" +- clocks: a handle for the "USB" clock +- resets: a handle for the shared "USB" reset line +- reg: The base address and length of the registers +- interrupts: the interrupt specifier for the OTG detection +- phys: handle to used PHYs on the system + - a <0> phandle can be used if a PHY is not used +- phy-names: names of the used PHYs on the system : + - "usb2-phy0" for USB2 PHY0 if USBHOST_A port is used + - "usb2-phy1" for USB2 PHY1 if USBOTG_B port is used + - "usb3-phy0" for USB3 PHY if USB3_0 is used +- dr_mode: should be "host", "peripheral", or "otg" depending on + the usage and configuration of the OTG Capable port. + - "host" and "peripheral" means a fixed Host or Device only connection + - "otg" means the port can be used as both Host or Device and + be switched automatically using the OTG ID pin. + +Optional properties: +- vbus-supply: should be a phandle to the regulator controlling the VBUS + power supply when used in OTG switchable mode + +Required child nodes: + +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +A child node must exist to represent the core DWC2 IP block. The name of +the node is not important. The content of the node is defined in dwc2.txt. + +PHY documentation is provided in the following places: +- Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt +- Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt + +Example device nodes: + usb: usb@ffe09000 { + compatible = "amlogic,meson-g12a-usb-ctrl"; + reg = <0x0 0xffe09000 0x0 0xa0>; + interrupts = ; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&clkc CLKID_USB>; + resets = <&reset RESET_USB>; + + dr_mode = "otg"; + + phys = <&usb2_phy0>, <&usb2_phy1>, + <&usb3_pcie_phy PHY_TYPE_USB3>; + phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0"; + + dwc2: usb@ff400000 { + compatible = "amlogic,meson-g12a-usb", "snps,dwc2"; + reg = <0x0 0xff400000 0x0 0x40000>; + interrupts = ; + clocks = <&clkc CLKID_USB1_DDR_BRIDGE>; + clock-names = "ddr"; + phys = <&usb2_phy1>; + dr_mode = "peripheral"; + g-rx-fifo-size = <192>; + g-np-tx-fifo-size = <128>; + g-tx-fifo-size = <128 128 16 16 16>; + }; + + dwc3: usb@ff500000 { + compatible = "snps,dwc3"; + reg = <0x0 0xff500000 0x0 0x100000>; + interrupts = ; + dr_mode = "host"; + snps,dis_u2_susphy_quirk; + snps,quirk-frame-length-adjustment; + }; + }; -- cgit v1.2.3