USB support =========== USB host support ---------------- barebox has support for both USB host and USB device mode. USB devices take a long time to probe, so they are not probed automatically. Probing has to be triggered using the :ref:`command_usb` or :ref:`command_detect` command. USB devices in barebox are not hot-pluggable. It is expected that USB devices are not disconnected while barebox is running. USB Networking ^^^^^^^^^^^^^^ barebox supports ASIX-compatible devices and the SMSC95xx. After detection, the device shows up as eth0 and can be used like a regular network device. To use a USB network device together with the :ref:`command_ifup` command, add the following to ``/env/network/eth0-discover``: .. code-block:: sh #!/bin/sh usb USB mass storage ^^^^^^^^^^^^^^^^ barebox supports USB mass storage devices. After probing them with the :ref:`command_usb` command, they show up as ``/dev/diskx`` and can be used like any other device. USB device support ------------------ DFU ^^^ USB Device Firmware Upgrade (DFU) is an official USB device class specification of the USB Implementers Forum. It provides a vendor-independent way to update the firmware of embedded devices. The current specification is version 1.1 and can be downloaded here: http://www.usb.org/developers/devclass_docs/DFU_1.1.pdf On the barebox side, the update is handled with the :ref:`command_dfu` command. It is passed a list of partitions to provide to the host. The partition list has the form ``()``. ``file`` is the path to the device or regular file which shall be updated. ``name`` is the name under which the partition shall be provided to the host. For the possible ``flags`` see :ref:`command_dfu`. A typical ``dfu`` command could look like this: .. code-block:: sh dfu "/dev/nand0.barebox.bb(barebox)sr,/dev/nand0.kernel.bb(kernel)r,/dev/nand0.root.bb(root)r" On the host side, the tool `dfu-util `_ can be used to update the partitions. It is available for most distributions and typically supports the following options:: dfu-util -h Usage: dfu-util [options] ... -h --help Print this help message -V --version Print the version number -v --verbose Print verbose debug statements -l --list List the currently attached DFU capable USB devices -e --detach Detach the currently attached DFU capable USB devices -d --device vendor:product Specify Vendor/Product ID of DFU device -p --path bus-port. ... .port Specify path to DFU device -c --cfg config_nr Specify the Configuration of DFU device -i --intf intf_nr Specify the DFU Interface number -a --alt alt Specify the Altsetting of the DFU Interface by name or by number -t --transfer-size Specify the number of bytes per USB Transfer -U --upload file Read firmware from device into -D --download file Write firmware from into device -R --reset Issue USB Reset signalling once we're finished -s --dfuse-address address ST DfuSe mode, specify target address for raw file download or upload. Not applicable for DfuSe file (.dfu) downloads To update the kernel for the above example, you would use something like the following: .. code-block:: sh dfu-util -D arch/arm/boot/zImage -a kernel The ``dfu-util`` command automatically finds DFU-capable devices. If there are multiple devices found, you need to identify one with the ``-d``/``-p`` options. USB serial console ^^^^^^^^^^^^^^^^^^ barebox can provide a serial console over USB. This can be initialized with the :ref:`command_usbserial` command. Once the host is plugged in it should show a new serial device, on Linux for example ``/dev/ttyACM0``. Android Fastboot support ^^^^^^^^^^^^^^^^^^^^^^^^ barebox has support for the android fastboot protocol. There is no dedicated command for initializing the fastboot protocol, instead it is integrated into the Multifunction Composite Gadget, see :`ref:command_usbgadget` for a usage description. The Fastboot gadget supports the following commands: - fastboot flash - fastboot getvar - fastboot boot - fastboot reboot **NOTE** ``fastboot erase`` is not yet implemented. This means flashing MTD partitions does not yet work. The barebox Fastboot gadget supports the following non standard extensions: - ``fastboot getvar all`` Shows a list of all variables - ``fastboot oem getenv `` Shows a barebox environment variable - ``fastboot oem setenv =`` Sets a barebox environment variable - ``fastboot oem exec `` executes a shell command. Note the output can't be seen on the host, but the fastboot command returns successfully when the barebox command was successful and it fails when the barebox command fails. USB Composite Multifunction Gadget ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ With the Composite Multifunction Gadget it is possible to create a USB device with multiple functions. A useful combination is creating a Fastboot gadget and a USB serial console. This combination can be created with: .. code-block:: sh usbgadget -A /dev/mmc2.0(root),/dev/mmc2.1(data) -a The ``-A`` option will create a Fastboot function providing ``/dev/mmc2.0`` as root partition and ``/dev/mmc2.1`` as data partition. The ``-a`` option will create a USB CDC ACM compliant serial device. Unlike the :ref:`command_dfu` command the ``usbgadget`` command returns immediately after creating the gadget. The gadget can be removed with ``usbgadget -d``.