// SPDX-License-Identifier: GPL-2.0 /** * core.c - DesignWare USB3 DRD Controller Core file * * Copyright (C) 2010-2011 Texas Instruments Incorporated - http://www.ti.com * * Authors: Felipe Balbi , * Sebastian Andrzej Siewior */ #include #include #include #include #include #include #include "gadget.h" #include "core.h" #include "io.h" #define DWC3_DEFAULT_AUTOSUSPEND_DELAY 5000 /* ms */ /** * dwc3_get_dr_mode - Validates and sets dr_mode * @dwc: pointer to our context structure */ static int dwc3_get_dr_mode(struct dwc3 *dwc) { enum usb_dr_mode mode; struct device_d *dev = dwc->dev; unsigned int hw_mode; if (dwc->dr_mode == USB_DR_MODE_UNKNOWN) dwc->dr_mode = USB_DR_MODE_OTG; mode = dwc->dr_mode; hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0); switch (hw_mode) { case DWC3_GHWPARAMS0_MODE_GADGET: if (IS_ENABLED(CONFIG_USB_DWC3_HOST)) { dev_err(dev, "Controller does not support host mode.\n"); return -EINVAL; } mode = USB_DR_MODE_PERIPHERAL; break; case DWC3_GHWPARAMS0_MODE_HOST: if (IS_ENABLED(CONFIG_USB_DWC3_GADGET)) { dev_err(dev, "Controller does not support device mode.\n"); return -EINVAL; } mode = USB_DR_MODE_HOST; break; default: if (IS_ENABLED(CONFIG_USB_DWC3_HOST)) mode = USB_DR_MODE_HOST; else if (IS_ENABLED(CONFIG_USB_DWC3_GADGET)) mode = USB_DR_MODE_PERIPHERAL; /* * DWC_usb31 and DWC_usb3 v3.30a and higher do not support OTG * mode. If the controller supports DRD but the dr_mode is not * specified or set to OTG, then set the mode to peripheral. */ if (mode == USB_DR_MODE_OTG && dwc->revision >= DWC3_REVISION_330A) mode = USB_DR_MODE_PERIPHERAL; } if (mode != dwc->dr_mode) { dev_warn(dev, "Configuration mismatch. dr_mode forced to %s\n", mode == USB_DR_MODE_HOST ? "host" : "gadget"); dwc->dr_mode = mode; } return 0; } void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode) { u32 reg; reg = dwc3_readl(dwc->regs, DWC3_GCTL); reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG)); reg |= DWC3_GCTL_PRTCAPDIR(mode); dwc3_writel(dwc->regs, DWC3_GCTL, reg); dwc->current_dr_role = mode; } /** * dwc3_core_soft_reset - Issues core soft reset and PHY reset * @dwc: pointer to our context structure */ static int dwc3_core_soft_reset(struct dwc3 *dwc) { u32 reg; int retries = 1000; int ret; ret = phy_init(dwc->usb2_generic_phy); if (ret < 0) return ret; ret = phy_init(dwc->usb3_generic_phy); if (ret < 0) { phy_exit(dwc->usb2_generic_phy); return ret; } /* * We're resetting only the device side because, if we're in host mode, * XHCI driver will reset the host block. If dwc3 was configured for * host-only mode, then we can return early. */ if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_HOST) return 0; reg = dwc3_readl(dwc->regs, DWC3_DCTL); reg |= DWC3_DCTL_CSFTRST; dwc3_writel(dwc->regs, DWC3_DCTL, reg); do { reg = dwc3_readl(dwc->regs, DWC3_DCTL); if (!(reg & DWC3_DCTL_CSFTRST)) goto done; udelay(1); } while (--retries); phy_exit(dwc->usb3_generic_phy); phy_exit(dwc->usb2_generic_phy); return -ETIMEDOUT; done: /* * For DWC_usb31 controller, once DWC3_DCTL_CSFTRST bit is cleared, * we must wait at least 50ms before accessing the PHY domain * (synchronization delay). DWC_usb31 programming guide section 1.3.2. */ if (dwc3_is_usb31(dwc)) mdelay(50); return 0; } /** * dwc3_free_one_event_buffer - Frees one event buffer * @dwc: Pointer to our controller context structure * @evt: Pointer to event buffer to be freed */ static void dwc3_free_one_event_buffer(struct dwc3 *dwc, struct dwc3_event_buffer *evt) { dma_free_coherent(evt->buf, 0, sizeof(dma_addr_t)); } /** * dwc3_alloc_one_event_buffer - Allocates one event buffer structure * @dwc: Pointer to our controller context structure * @length: size of the event buffer * * Returns a pointer to the allocated event buffer structure on success * otherwise ERR_PTR(errno). */ static struct dwc3_event_buffer *dwc3_alloc_one_event_buffer(struct dwc3 *dwc, unsigned length) { struct dwc3_event_buffer *evt; evt = xzalloc(sizeof(*evt)); if (!evt) return ERR_PTR(-ENOMEM); evt->dwc = dwc; evt->length = length; evt->buf = dma_alloc_coherent(length, &evt->dma); if (!evt->buf) return ERR_PTR(-ENOMEM); return evt; } /** * dwc3_free_event_buffers - frees all allocated event buffers * @dwc: Pointer to our controller context structure */ static void dwc3_free_event_buffers(struct dwc3 *dwc) { struct dwc3_event_buffer *evt; evt = dwc->ev_buf; if (evt) dwc3_free_one_event_buffer(dwc, evt); } /** * dwc3_alloc_event_buffers - Allocates @num event buffers of size @length * @dwc: pointer to our controller context structure * @length: size of event buffer * * Returns 0 on success otherwise negative errno. In the error case, dwc * may contain some buffers allocated but not all which were requested. */ static int dwc3_alloc_event_buffers(struct dwc3 *dwc, unsigned length) { struct dwc3_event_buffer *evt; evt = dwc3_alloc_one_event_buffer(dwc, length); if (IS_ERR(evt)) { dev_err(dwc->dev, "can't allocate event buffer\n"); return PTR_ERR(evt); } dwc->ev_buf = evt; return 0; } /** * dwc3_event_buffers_setup - setup our allocated event buffers * @dwc: pointer to our controller context structure * * Returns 0 on success otherwise negative errno. */ static int dwc3_event_buffers_setup(struct dwc3 *dwc) { struct dwc3_event_buffer *evt; evt = dwc->ev_buf; evt->lpos = 0; dwc3_writel(dwc->regs, DWC3_GEVNTADRLO(0), lower_32_bits(evt->dma)); dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(0), upper_32_bits(evt->dma)); dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0), DWC3_GEVNTSIZ_SIZE(evt->length)); dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), 0); return 0; } static void dwc3_event_buffers_cleanup(struct dwc3 *dwc) { struct dwc3_event_buffer *evt; evt = dwc->ev_buf; evt->lpos = 0; dwc3_writel(dwc->regs, DWC3_GEVNTADRLO(0), 0); dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(0), 0); dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0), DWC3_GEVNTSIZ_INTMASK | DWC3_GEVNTSIZ_SIZE(0)); dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), 0); } static int dwc3_alloc_scratch_buffers(struct dwc3 *dwc) { if (!dwc->has_hibernation) return 0; if (!dwc->nr_scratch) return 0; dwc->scratchbuf = kmalloc_array(dwc->nr_scratch, DWC3_SCRATCHBUF_SIZE, GFP_KERNEL); if (!dwc->scratchbuf) return -ENOMEM; return 0; } static int dwc3_setup_scratch_buffers(struct dwc3 *dwc) { dma_addr_t scratch_addr; u32 param; int ret; if (!dwc->has_hibernation) return 0; if (!dwc->nr_scratch) return 0; scratch_addr = dma_map_single(dwc->dev, dwc->scratchbuf, dwc->nr_scratch * DWC3_SCRATCHBUF_SIZE, DMA_BIDIRECTIONAL); if (dma_mapping_error(dwc->dev, scratch_addr)) { dev_err(dwc->dev, "failed to map scratch buffer\n"); ret = -EFAULT; goto err0; } dwc->scratch_addr = scratch_addr; param = lower_32_bits(scratch_addr); ret = dwc3_send_gadget_generic_command(dwc, DWC3_DGCMD_SET_SCRATCHPAD_ADDR_LO, param); if (ret < 0) goto err1; param = upper_32_bits(scratch_addr); ret = dwc3_send_gadget_generic_command(dwc, DWC3_DGCMD_SET_SCRATCHPAD_ADDR_HI, param); if (ret < 0) goto err1; return 0; err1: dma_unmap_single(dwc->dev, dwc->scratch_addr, dwc->nr_scratch * DWC3_SCRATCHBUF_SIZE, DMA_BIDIRECTIONAL); err0: return ret; } static const struct clk_bulk_data dwc3_core_clks[] = { { .id = "ref" }, { .id = "bus_early" }, { .id = "suspend" }, }; /* * dwc3_frame_length_adjustment - Adjusts frame length if required * @dwc3: Pointer to our controller context structure */ static void dwc3_frame_length_adjustment(struct dwc3 *dwc) { u32 reg; u32 dft; if (dwc->revision < DWC3_REVISION_250A) return; if (dwc->fladj == 0) return; reg = dwc3_readl(dwc->regs, DWC3_GFLADJ); dft = reg & DWC3_GFLADJ_30MHZ_MASK; reg &= ~DWC3_GFLADJ_30MHZ_MASK; reg |= DWC3_GFLADJ_30MHZ_SDBND_SEL | dwc->fladj; dwc3_writel(dwc->regs, DWC3_GFLADJ, reg); } static void dwc3_core_num_eps(struct dwc3 *dwc) { struct dwc3_hwparams *parms = &dwc->hwparams; dwc->num_eps = DWC3_NUM_EPS(parms); } static void dwc3_cache_hwparams(struct dwc3 *dwc) { struct dwc3_hwparams *parms = &dwc->hwparams; parms->hwparams0 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS0); parms->hwparams1 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS1); parms->hwparams2 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS2); parms->hwparams3 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS3); parms->hwparams4 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS4); parms->hwparams5 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS5); parms->hwparams6 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS6); parms->hwparams7 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS7); parms->hwparams8 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS8); } static int dwc3_core_ulpi_init(struct dwc3 *dwc) { int intf; int ret = 0; intf = DWC3_GHWPARAMS3_HSPHY_IFC(dwc->hwparams.hwparams3); if (intf == DWC3_GHWPARAMS3_HSPHY_IFC_ULPI || (intf == DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI && dwc->hsphy_interface && !strncmp(dwc->hsphy_interface, "ulpi", 4))) ret = dwc3_ulpi_init(dwc); return ret; } /** * dwc3_phy_setup - Configure USB PHY Interface of DWC3 Core * @dwc: Pointer to our controller context structure * * Returns 0 on success. The USB PHY interfaces are configured but not * initialized. The PHY interfaces and the PHYs get initialized together with * the core in dwc3_core_init. */ static int dwc3_phy_setup(struct dwc3 *dwc) { u32 reg; reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0)); /* * Make sure UX_EXIT_PX is cleared as that causes issues with some * PHYs. Also, this bit is not supposed to be used in normal operation. */ reg &= ~DWC3_GUSB3PIPECTL_UX_EXIT_PX; /* * Above 1.94a, it is recommended to set DWC3_GUSB3PIPECTL_SUSPHY * to '0' during coreConsultant configuration. So default value * will be '0' when the core is reset. Application needs to set it * to '1' after the core initialization is completed. */ if (dwc->revision > DWC3_REVISION_194A) reg |= DWC3_GUSB3PIPECTL_SUSPHY; if (dwc->u2ss_inp3_quirk) reg |= DWC3_GUSB3PIPECTL_U2SSINP3OK; if (dwc->dis_rxdet_inp3_quirk) reg |= DWC3_GUSB3PIPECTL_DISRXDETINP3; if (dwc->req_p1p2p3_quirk) reg |= DWC3_GUSB3PIPECTL_REQP1P2P3; if (dwc->del_p1p2p3_quirk) reg |= DWC3_GUSB3PIPECTL_DEP1P2P3_EN; if (dwc->del_phy_power_chg_quirk) reg |= DWC3_GUSB3PIPECTL_DEPOCHANGE; if (dwc->lfps_filter_quirk) reg |= DWC3_GUSB3PIPECTL_LFPSFILT; if (dwc->rx_detect_poll_quirk) reg |= DWC3_GUSB3PIPECTL_RX_DETOPOLL; if (dwc->tx_de_emphasis_quirk) reg |= DWC3_GUSB3PIPECTL_TX_DEEPH(dwc->tx_de_emphasis); if (dwc->dis_u3_susphy_quirk) reg &= ~DWC3_GUSB3PIPECTL_SUSPHY; if (dwc->dis_del_phy_power_chg_quirk) reg &= ~DWC3_GUSB3PIPECTL_DEPOCHANGE; dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg); reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); /* Select the HS PHY interface */ switch (DWC3_GHWPARAMS3_HSPHY_IFC(dwc->hwparams.hwparams3)) { case DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI: if (dwc->hsphy_interface && !strncmp(dwc->hsphy_interface, "utmi", 4)) { reg &= ~DWC3_GUSB2PHYCFG_ULPI_UTMI; break; } else if (dwc->hsphy_interface && !strncmp(dwc->hsphy_interface, "ulpi", 4)) { reg |= DWC3_GUSB2PHYCFG_ULPI_UTMI; dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg); } else { /* Relying on default value. */ if (!(reg & DWC3_GUSB2PHYCFG_ULPI_UTMI)) break; } /* FALLTHROUGH */ case DWC3_GHWPARAMS3_HSPHY_IFC_ULPI: /* FALLTHROUGH */ default: break; } switch (dwc->hsphy_mode) { case USBPHY_INTERFACE_MODE_UTMI: reg &= ~(DWC3_GUSB2PHYCFG_PHYIF_MASK | DWC3_GUSB2PHYCFG_USBTRDTIM_MASK); reg |= DWC3_GUSB2PHYCFG_PHYIF(UTMI_PHYIF_8_BIT) | DWC3_GUSB2PHYCFG_USBTRDTIM(USBTRDTIM_UTMI_8_BIT); break; case USBPHY_INTERFACE_MODE_UTMIW: reg &= ~(DWC3_GUSB2PHYCFG_PHYIF_MASK | DWC3_GUSB2PHYCFG_USBTRDTIM_MASK); reg |= DWC3_GUSB2PHYCFG_PHYIF(UTMI_PHYIF_16_BIT) | DWC3_GUSB2PHYCFG_USBTRDTIM(USBTRDTIM_UTMI_16_BIT); break; default: break; } /* * Above 1.94a, it is recommended to set DWC3_GUSB2PHYCFG_SUSPHY to * '0' during coreConsultant configuration. So default value will * be '0' when the core is reset. Application needs to set it to * '1' after the core initialization is completed. */ if (dwc->revision > DWC3_REVISION_194A) reg |= DWC3_GUSB2PHYCFG_SUSPHY; if (dwc->dis_u2_susphy_quirk) reg &= ~DWC3_GUSB2PHYCFG_SUSPHY; if (dwc->dis_enblslpm_quirk) reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM; else reg |= DWC3_GUSB2PHYCFG_ENBLSLPM; if (dwc->dis_u2_freeclk_exists_quirk) reg &= ~DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS; dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg); return 0; } static void dwc3_core_exit(struct dwc3 *dwc) { dwc3_event_buffers_cleanup(dwc); phy_exit(dwc->usb2_generic_phy); phy_exit(dwc->usb3_generic_phy); phy_power_off(dwc->usb2_generic_phy); phy_power_off(dwc->usb3_generic_phy); clk_bulk_disable(dwc->num_clks, dwc->clks); dwc3_free_event_buffers(dwc); } static bool dwc3_core_is_valid(struct dwc3 *dwc) { u32 reg; reg = dwc3_readl(dwc->regs, DWC3_GSNPSID); /* This should read as U3 followed by revision number */ if ((reg & DWC3_GSNPSID_MASK) == 0x55330000) { /* Detected DWC_usb3 IP */ dwc->revision = reg; } else if ((reg & DWC3_GSNPSID_MASK) == 0x33310000) { /* Detected DWC_usb31 IP */ dwc->revision = dwc3_readl(dwc->regs, DWC3_VER_NUMBER); dwc->revision |= DWC3_REVISION_IS_DWC31; dwc->version_type = dwc3_readl(dwc->regs, DWC3_VER_TYPE); } else { return false; } return true; } static void dwc3_core_setup_global_control(struct dwc3 *dwc) { u32 hwparams4 = dwc->hwparams.hwparams4; u32 reg; reg = dwc3_readl(dwc->regs, DWC3_GCTL); reg &= ~DWC3_GCTL_SCALEDOWN_MASK; switch (DWC3_GHWPARAMS1_EN_PWROPT(dwc->hwparams.hwparams1)) { case DWC3_GHWPARAMS1_EN_PWROPT_CLK: /** * WORKAROUND: DWC3 revisions between 2.10a and 2.50a have an * issue which would cause xHCI compliance tests to fail. * * Because of that we cannot enable clock gating on such * configurations. * * Refers to: * * STAR#9000588375: Clock Gating, SOF Issues when ref_clk-Based * SOF/ITP Mode Used */ if ((dwc->dr_mode == USB_DR_MODE_HOST || dwc->dr_mode == USB_DR_MODE_OTG) && (dwc->revision >= DWC3_REVISION_210A && dwc->revision <= DWC3_REVISION_250A)) reg |= DWC3_GCTL_DSBLCLKGTNG | DWC3_GCTL_SOFITPSYNC; else reg &= ~DWC3_GCTL_DSBLCLKGTNG; break; case DWC3_GHWPARAMS1_EN_PWROPT_HIB: /* enable hibernation here */ dwc->nr_scratch = DWC3_GHWPARAMS4_HIBER_SCRATCHBUFS(hwparams4); /* * REVISIT Enabling this bit so that host-mode hibernation * will work. Device-mode hibernation is not yet implemented. */ reg |= DWC3_GCTL_GBLHIBERNATIONEN; break; default: /* nothing */ break; } /* check if current dwc3 is on simulation board */ if (dwc->hwparams.hwparams6 & DWC3_GHWPARAMS6_EN_FPGA) { dev_info(dwc->dev, "Running with FPGA optimizations\n"); dwc->is_fpga = true; } WARN(dwc->disable_scramble_quirk && !dwc->is_fpga, "disable_scramble cannot be used on non-FPGA builds\n"); if (dwc->disable_scramble_quirk && dwc->is_fpga) reg |= DWC3_GCTL_DISSCRAMBLE; else reg &= ~DWC3_GCTL_DISSCRAMBLE; if (dwc->u2exit_lfps_quirk) reg |= DWC3_GCTL_U2EXIT_LFPS; /* * WORKAROUND: DWC3 revisions <1.90a have a bug * where the device can fail to connect at SuperSpeed * and falls back to high-speed mode which causes * the device to enter a Connect/Disconnect loop */ if (dwc->revision < DWC3_REVISION_190A) reg |= DWC3_GCTL_U2RSTECN; dwc3_writel(dwc->regs, DWC3_GCTL, reg); } static int dwc3_core_get_phy(struct dwc3 *dwc); /* set global incr burst type configuration registers */ static void dwc3_set_incr_burst_type(struct dwc3 *dwc) { struct device_d *dev = dwc->dev; /* incrx_mode : for INCR burst type. */ bool incrx_mode; /* incrx_size : for size of INCRX burst. */ u32 incrx_size; u32 *vals; u32 cfg; int ntype = 0; int ret; int i; cfg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0); /* * Handle property "snps,incr-burst-type-adjustment". * Get the number of value from this property: * result <= 0, means this property is not supported. * result = 1, means INCRx burst mode supported. * result > 1, means undefined length burst mode supported. */ of_find_property(dev->device_node, "snps,incr-burst-type-adjustment", &ntype); ntype /= sizeof(u32); if (ntype <= 0) return; vals = kcalloc(ntype, sizeof(u32), GFP_KERNEL); if (!vals) { dev_err(dev, "Error to get memory\n"); return; } /* Get INCR burst type, and parse it */ ret = of_property_read_u32_array(dev->device_node, "snps,incr-burst-type-adjustment", vals, ntype); if (ret) { kfree(vals); dev_err(dev, "Error to get property\n"); return; } incrx_size = *vals; if (ntype > 1) { /* INCRX (undefined length) burst mode */ incrx_mode = INCRX_UNDEF_LENGTH_BURST_MODE; for (i = 1; i < ntype; i++) { if (vals[i] > incrx_size) incrx_size = vals[i]; } } else { /* INCRX burst mode */ incrx_mode = INCRX_BURST_MODE; } kfree(vals); /* Enable Undefined Length INCR Burst and Enable INCRx Burst */ cfg &= ~DWC3_GSBUSCFG0_INCRBRST_MASK; if (incrx_mode) cfg |= DWC3_GSBUSCFG0_INCRBRSTENA; switch (incrx_size) { case 256: cfg |= DWC3_GSBUSCFG0_INCR256BRSTENA; break; case 128: cfg |= DWC3_GSBUSCFG0_INCR128BRSTENA; break; case 64: cfg |= DWC3_GSBUSCFG0_INCR64BRSTENA; break; case 32: cfg |= DWC3_GSBUSCFG0_INCR32BRSTENA; break; case 16: cfg |= DWC3_GSBUSCFG0_INCR16BRSTENA; break; case 8: cfg |= DWC3_GSBUSCFG0_INCR8BRSTENA; break; case 4: cfg |= DWC3_GSBUSCFG0_INCR4BRSTENA; break; case 1: break; default: dev_err(dev, "Invalid property\n"); break; } dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, cfg); } /** * dwc3_core_init - Low-level initialization of DWC3 Core * @dwc: Pointer to our controller context structure * * Returns 0 on success otherwise negative errno. */ static int dwc3_core_init(struct dwc3 *dwc) { u32 reg; int ret; if (!dwc3_core_is_valid(dwc)) { dev_err(dwc->dev, "this is not a DesignWare USB3 DRD Core\n"); ret = -ENODEV; goto err0; } /* * Write Linux Version Code to our GUID register so it's easy to figure * out which kernel version a bug was found. */ dwc3_writel(dwc->regs, DWC3_GUID, 0xdeadbeef); /* Handle USB2.0-only core configuration */ if (DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3) == DWC3_GHWPARAMS3_SSPHY_IFC_DIS) { if (dwc->maximum_speed == USB_SPEED_SUPER) dwc->maximum_speed = USB_SPEED_HIGH; } ret = dwc3_phy_setup(dwc); if (ret) goto err0; if (!dwc->ulpi_ready) { ret = dwc3_core_ulpi_init(dwc); if (ret) goto err0; dwc->ulpi_ready = true; } if (!dwc->phys_ready) { ret = dwc3_core_get_phy(dwc); if (ret) goto err0a; dwc->phys_ready = true; } ret = dwc3_core_soft_reset(dwc); if (ret) goto err0a; dwc3_core_setup_global_control(dwc); dwc3_core_num_eps(dwc); ret = dwc3_setup_scratch_buffers(dwc); if (ret) goto err0a; /* Adjust Frame Length */ dwc3_frame_length_adjustment(dwc); dwc3_set_incr_burst_type(dwc); ret = phy_power_on(dwc->usb2_generic_phy); if (ret < 0) goto err1; ret = phy_power_on(dwc->usb3_generic_phy); if (ret < 0) goto err2; ret = dwc3_event_buffers_setup(dwc); if (ret) { dev_err(dwc->dev, "failed to setup event buffers\n"); goto err3; } /* * ENDXFER polling is available on version 3.10a and later of * the DWC_usb3 controller. It is NOT available in the * DWC_usb31 controller. */ if (!dwc3_is_usb31(dwc) && dwc->revision >= DWC3_REVISION_310A) { reg = dwc3_readl(dwc->regs, DWC3_GUCTL2); reg |= DWC3_GUCTL2_RST_ACTBITLATER; dwc3_writel(dwc->regs, DWC3_GUCTL2, reg); } if (dwc->revision >= DWC3_REVISION_250A) { reg = dwc3_readl(dwc->regs, DWC3_GUCTL1); /* * Enable hardware control of sending remote wakeup * in HS when the device is in the L1 state. */ if (dwc->revision >= DWC3_REVISION_290A) reg |= DWC3_GUCTL1_DEV_L1_EXIT_BY_HW; if (dwc->dis_tx_ipgap_linecheck_quirk) reg |= DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS; dwc3_writel(dwc->regs, DWC3_GUCTL1, reg); } if (dwc->dr_mode == USB_DR_MODE_HOST || dwc->dr_mode == USB_DR_MODE_OTG) { reg = dwc3_readl(dwc->regs, DWC3_GUCTL); /* * Enable Auto retry Feature to make the controller operating in * Host mode on seeing transaction errors(CRC errors or internal * overrun scenerios) on IN transfers to reply to the device * with a non-terminating retry ACK (i.e, an ACK transcation * packet with Retry=1 & Nump != 0) */ reg |= DWC3_GUCTL_HSTINAUTORETRY; dwc3_writel(dwc->regs, DWC3_GUCTL, reg); } /* * Must config both number of packets and max burst settings to enable * RX and/or TX threshold. */ if (dwc3_is_usb31(dwc) && dwc->dr_mode == USB_DR_MODE_HOST) { u8 rx_thr_num = dwc->rx_thr_num_pkt_prd; u8 rx_maxburst = dwc->rx_max_burst_prd; u8 tx_thr_num = dwc->tx_thr_num_pkt_prd; u8 tx_maxburst = dwc->tx_max_burst_prd; if (rx_thr_num && rx_maxburst) { reg = dwc3_readl(dwc->regs, DWC3_GRXTHRCFG); reg |= DWC31_RXTHRNUMPKTSEL_PRD; reg &= ~DWC31_RXTHRNUMPKT_PRD(~0); reg |= DWC31_RXTHRNUMPKT_PRD(rx_thr_num); reg &= ~DWC31_MAXRXBURSTSIZE_PRD(~0); reg |= DWC31_MAXRXBURSTSIZE_PRD(rx_maxburst); dwc3_writel(dwc->regs, DWC3_GRXTHRCFG, reg); } if (tx_thr_num && tx_maxburst) { reg = dwc3_readl(dwc->regs, DWC3_GTXTHRCFG); reg |= DWC31_TXTHRNUMPKTSEL_PRD; reg &= ~DWC31_TXTHRNUMPKT_PRD(~0); reg |= DWC31_TXTHRNUMPKT_PRD(tx_thr_num); reg &= ~DWC31_MAXTXBURSTSIZE_PRD(~0); reg |= DWC31_MAXTXBURSTSIZE_PRD(tx_maxburst); dwc3_writel(dwc->regs, DWC3_GTXTHRCFG, reg); } } return 0; err3: phy_power_off(dwc->usb3_generic_phy); err2: phy_power_off(dwc->usb2_generic_phy); err1: phy_exit(dwc->usb2_generic_phy); phy_exit(dwc->usb3_generic_phy); err0a: err0: return ret; } static int dwc3_core_get_phy(struct dwc3 *dwc) { struct device_d *dev = dwc->dev; int ret; dwc->usb2_generic_phy = phy_get(dev, "usb2-phy"); if (IS_ERR(dwc->usb2_generic_phy)) { ret = PTR_ERR(dwc->usb2_generic_phy); if (ret == -ENOSYS || ret == -ENODEV) { dwc->usb2_generic_phy = NULL; } else if (ret == -EPROBE_DEFER) { return ret; } else { dev_err(dev, "no usb2 phy configured\n"); return ret; } } dwc->usb3_generic_phy = phy_get(dev, "usb3-phy"); if (IS_ERR(dwc->usb3_generic_phy)) { ret = PTR_ERR(dwc->usb3_generic_phy); if (ret == -ENOSYS || ret == -ENODEV) { dwc->usb3_generic_phy = NULL; } else if (ret == -EPROBE_DEFER) { return ret; } else { dev_err(dev, "no usb3 phy configured\n"); return ret; } } return 0; } static int dwc3_set_mode(void *ctx, enum usb_dr_mode mode) { struct dwc3 *dwc = ctx; struct device_d *dev = dwc->dev; int ret; switch (mode) { case USB_DR_MODE_PERIPHERAL: dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE); ret = dwc3_gadget_init(dwc); if (ret) { if (ret != -EPROBE_DEFER) dev_err(dev, "failed to initialize gadget\n"); return ret; } break; case USB_DR_MODE_HOST: dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); ret = dwc3_host_init(dwc); if (ret) { if (ret != -EPROBE_DEFER) dev_err(dev, "failed to initialize host\n"); return ret; } break; default: return -EINVAL; } return 0; } static int dwc3_core_init_mode(struct dwc3 *dwc) { if (dwc->dr_mode == USB_DR_MODE_OTG) return usb_register_otg_device(dwc->dev, dwc3_set_mode, dwc); else return dwc3_set_mode(dwc, dwc->dr_mode); } static void dwc3_get_properties(struct dwc3 *dwc) { struct device_d *dev = dwc->dev; u8 lpm_nyet_threshold; u8 tx_de_emphasis; u8 hird_threshold; /* default to highest possible threshold */ lpm_nyet_threshold = 0xff; /* default to -3.5dB de-emphasis */ tx_de_emphasis = 1; /* * default to assert utmi_sleep_n and use maximum allowed HIRD * threshold value of 0b1100 */ hird_threshold = 12; dwc->maximum_speed = of_usb_get_maximum_speed(dev->device_node, NULL); dwc->dr_mode = of_usb_get_dr_mode(dev->device_node, NULL); dwc->hsphy_mode = of_usb_get_phy_mode(dev->device_node, NULL); dwc->lpm_nyet_threshold = lpm_nyet_threshold; dwc->tx_de_emphasis = tx_de_emphasis; if (of_get_property(dev->device_node, "snps,dis_rxdet_inp3_quirk", NULL)) dwc->dis_rxdet_inp3_quirk = 1; of_property_read_u32_array(dev->device_node, "snps,quirk-frame-length-adjustment", &dwc->fladj, 1); dwc->hird_threshold = hird_threshold | (dwc->is_utmi_l1_suspend << 4); dwc->imod_interval = 0; } /* check whether the core supports IMOD */ bool dwc3_has_imod(struct dwc3 *dwc) { return ((dwc3_is_usb3(dwc) && dwc->revision >= DWC3_REVISION_300A) || (dwc3_is_usb31(dwc) && dwc->revision >= DWC3_USB31_REVISION_120A)); } static void dwc3_check_params(struct dwc3 *dwc) { struct device_d *dev = dwc->dev; /* Check for proper value of imod_interval */ if (dwc->imod_interval && !dwc3_has_imod(dwc)) { dev_warn(dwc->dev, "Interrupt moderation not supported\n"); dwc->imod_interval = 0; } /* * Workaround for STAR 9000961433 which affects only version * 3.00a of the DWC_usb3 core. This prevents the controller * interrupt from being masked while handling events. IMOD * allows us to work around this issue. Enable it for the * affected version. */ if (!dwc->imod_interval && (dwc->revision == DWC3_REVISION_300A)) dwc->imod_interval = 1; /* Check the maximum_speed parameter */ switch (dwc->maximum_speed) { case USB_SPEED_LOW: case USB_SPEED_FULL: case USB_SPEED_HIGH: case USB_SPEED_SUPER: case USB_SPEED_SUPER_PLUS: break; default: dev_err(dev, "invalid maximum_speed parameter %d\n", dwc->maximum_speed); /* fall through */ case USB_SPEED_UNKNOWN: /* default to superspeed */ dwc->maximum_speed = USB_SPEED_SUPER; /* * default to superspeed plus if we are capable. */ if (dwc3_is_usb31(dwc) && (DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3) == DWC3_GHWPARAMS3_SSPHY_IFC_GEN2)) dwc->maximum_speed = USB_SPEED_SUPER_PLUS; break; } } static void dwc3_coresoft_reset(struct dwc3 *dwc) { u32 reg; reg = dwc3_readl(dwc->regs, DWC3_GCTL); reg |= DWC3_GCTL_CORESOFTRESET; dwc3_writel(dwc->regs, DWC3_GCTL, reg); /* * Similar reset sequence in U-Boot has a 100ms delay here. In * practice reset sequence seem to work as expected even * without a delay. */ reg = dwc3_readl(dwc->regs, DWC3_GCTL); reg &= ~DWC3_GCTL_CORESOFTRESET; dwc3_writel(dwc->regs, DWC3_GCTL, reg); } static int dwc3_probe(struct device_d *dev) { struct dwc3 *dwc; int ret; dwc = xzalloc(sizeof(*dwc)); dev->priv = dwc; dwc->clks = xmemdup(dwc3_core_clks, sizeof(dwc3_core_clks)); dwc->dev = dev; dwc->regs = dev_get_mem_region(dwc->dev, 0) + DWC3_GLOBALS_REGS_START; dwc3_get_properties(dwc); if (dev->device_node) { dwc->num_clks = ARRAY_SIZE(dwc3_core_clks); if (of_find_property(dev->device_node, "clocks", NULL)) { ret = clk_bulk_get(dev, dwc->num_clks, dwc->clks); if (ret == -EPROBE_DEFER) return ret; if (ret) return ret; } } ret = clk_bulk_enable(dwc->num_clks, dwc->clks); if (ret) return ret; dwc3_coresoft_reset(dwc); dwc3_cache_hwparams(dwc); ret = dwc3_alloc_event_buffers(dwc, DWC3_EVENT_BUFFERS_SIZE); if (ret) { dev_err(dwc->dev, "failed to allocate event buffers\n"); return -ENOMEM; } ret = dwc3_get_dr_mode(dwc); if (ret) return ret; ret = dwc3_alloc_scratch_buffers(dwc); if (ret) return ret; ret = dwc3_core_init(dwc); if (ret) { if (ret != -EPROBE_DEFER) dev_err(dev, "failed to initialize core: %d\n", ret); return ret; } dwc3_check_params(dwc); ret = dwc3_core_init_mode(dwc); if (ret) return ret; return 0; } static void dwc3_remove(struct device_d *dev) { struct dwc3 *dwc = dev->priv; dwc3_core_exit(dwc); clk_bulk_put(dwc->num_clks, dwc->clks); } static const struct of_device_id of_dwc3_match[] = { { .compatible = "snps,dwc3" }, { .compatible = "synopsys,dwc3" }, { }, }; static struct driver_d dwc3_driver = { .probe = dwc3_probe, .remove = dwc3_remove, .name = "dwc3", .of_compatible = DRV_OF_COMPAT(of_dwc3_match), }; device_platform_driver(dwc3_driver);