# SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- $id: http://devicetree.org/schemas/pci/snps,dw-pcie.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# title: Synopsys DesignWare PCIe interface maintainers: - Jingoo Han - Gustavo Pimentel description: | Synopsys DesignWare PCIe host controller # Please create a separate DT-schema for your DWC PCIe Root Port controller # and make sure it's assigned with the vendor-specific compatible string. select: properties: compatible: const: snps,dw-pcie required: - compatible allOf: - $ref: /schemas/pci/pci-bus.yaml# - $ref: /schemas/pci/snps,dw-pcie-common.yaml# - if: not: required: - msi-map then: properties: interrupt-names: contains: const: msi properties: reg: description: At least DBI reg-space and peripheral devices CFG-space outbound window are required for the normal controller work. iATU memory IO region is also required if the space is unrolled (IP-core version >= 4.80a). minItems: 2 maxItems: 7 reg-names: minItems: 2 maxItems: 7 items: oneOf: - description: Basic DWC PCIe controller configuration-space accessible over the DBI interface. This memory space is either activated with CDM/ELBI = 0 and CS2 = 0 or is a contiguous memory region with all spaces. Note iATU/eDMA CSRs are indirectly accessible via the PL viewports on the DWC PCIe controllers older than v4.80a. const: dbi - description: Shadow DWC PCIe config-space registers. This space is selected by setting CDM/ELBI = 0 and CS2 = 1. This is an intermix of the PCI-SIG PCIe CFG-space with the shadow registers for some PCI Header space, PCI Standard and Extended Structures. It's mainly relevant for the end-point controller configuration, but still there are some shadow registers available for the Root Port mode too. const: dbi2 - description: External Local Bus registers. It's an application-dependent registers normally defined by the platform engineers. The space can be selected by setting CDM/ELBI = 1 and CS2 = 0 wires or can be accessed over some platform-specific means (for instance as a part of a system controller). enum: [ elbi, app ] - description: iATU/eDMA registers common for all device functions. It's an unrolled memory space with the internal Address Translation Unit and Enhanced DMA, which is selected by setting CDM/ELBI = 1 and CS2 = 1. For IP-core releases prior v4.80a, these registers have been programmed via an indirect addressing scheme using a set of viewport CSRs mapped into the PL space. Note iATU is normally mapped to the 0x0 address of this region, while eDMA is available at 0x80000 base address. const: atu - description: Platform-specific eDMA registers. Some platforms may have eDMA CSRs mapped in a non-standard base address. The registers offset can be changed or the MS/LS-bits of the address can be attached in an additional RTL block before the MEM-IO transactions reach the DW PCIe slave interface. const: dma - description: PHY/PCS configuration registers. Some platforms can have the PCS and PHY CSRs accessible over a dedicated memory mapped region, but mainly these registers are indirectly accessible either by means of the embedded PHY viewport schema or by some platform-specific method. const: phy - description: Outbound iATU-capable memory-region which will be used to access the peripheral PCIe devices configuration space. const: config - description: Vendor-specific CSR names. Consider using the generic names above for new bindings. oneOf: - description: See native 'elbi/app' CSR region for details. enum: [ apb, mgmt, link, ulreg, appl ] - description: See native 'atu' CSR region for details. enum: [ atu_dma ] - description: Syscon-related CSR regions. enum: [ smu, mpu ] - description: Tegra234 aperture enum: [ ecam ] allOf: - contains: const: dbi - contains: const: config interrupts: description: DWC PCIe Root Port/Complex specific IRQ signals. At least MSI interrupt signal is supposed to be specified for the host controller. minItems: 1 maxItems: 26 interrupt-names: minItems: 1 maxItems: 26 items: oneOf: - description: Controller request to read or write virtual product data from/to the VPD capability registers. const: vpd - description: Link Equalization Request flag is set in the Link Status 2 register (applicable if the corresponding IRQ is enabled in the Link Control 3 register). const: l_eq - description: Indicates that the eDMA Tx/Rx transfer is complete or that an error has occurred on the corresponding channel. eDMA can have eight Tx (Write) and Rx (Read) eDMA channels thus supporting up to 16 IRQ signals all together. Write eDMA channels shall go first in the ordered row as per default edma_int[*] bus setup. pattern: '^dma([0-9]|1[0-5])?$' - description: PCIe protocol correctable error or a Data Path protection correctable error is detected by the automotive/safety feature. const: sft_ce - description: Indicates that the internal safety mechanism has detected an uncorrectable error. const: sft_ue - description: Application-specific IRQ raised depending on the vendor-specific events basis. const: app - description: DSP AXI MSI Interrupt detected. It gets de-asserted when there is no more MSI interrupt pending. The interrupt is relevant to the iMSI-RX - Integrated MSI Receiver (AXI bridge). const: msi - description: Legacy A/B/C/D interrupt signal. Basically it's triggered by receiving a Assert_INT{A,B,C,D}/Desassert_INT{A,B,C,D} message from the downstream device. pattern: "^int(a|b|c|d)$" - description: Error condition detected and a flag is set in the Root Error Status register of the AER capability. It's asserted when the RC internally generated an error or an error message is received by the RC. const: aer - description: PME message is received by the port. That means having the PME status bit set in the Root Status register (the event is supposed to be unmasked in the Root Control register). const: pme - description: Hot-plug event is detected. That is a bit has been set in the Slot Status register and the corresponding event is enabled in the Slot Control register. const: hp - description: Link Autonomous Bandwidth Status flag has been set in the Link Status register (the event is supposed to be unmasked in the Link Control register). const: bw_au - description: Bandwidth Management Status flag has been set in the Link Status register (the event is supposed to be unmasked in the Link Control register). const: bw_mg - description: Combined Legacy A/B/C/D interrupt signal. See "^int(a|b|c|d)$" for details. const: legacy - description: Vendor-specific IRQ names. Consider using the generic names above for new bindings. oneOf: - description: See native "app" IRQ for details enum: [ intr, sys, pmc, msg, err ] additionalProperties: true required: - compatible - reg - reg-names examples: - | pcie@dfc00000 { compatible = "snps,dw-pcie"; device_type = "pci"; reg = <0xdfc00000 0x0001000>, /* IP registers */ <0xd0000000 0x0002000>; /* Configuration space */ reg-names = "dbi", "config"; #address-cells = <3>; #size-cells = <2>; ranges = <0x81000000 0 0x00000000 0xde000000 0 0x00010000>, <0x82000000 0 0xd0400000 0xd0400000 0 0x0d000000>; bus-range = <0x0 0xff>; interrupts = <25>, <24>; interrupt-names = "msi", "hp"; #interrupt-cells = <1>; reset-gpios = <&port0 0 1>; phys = <&pcie_phy>; phy-names = "pcie"; num-lanes = <1>; max-link-speed = <3>; };