* Freescale IMX27 IOMUX Controller Required properties: - compatible: "fsl,imx27-iomuxc" The iomuxc driver node should define subnodes containing of pinctrl configuration subnodes. Required properties for pin configuration node: - fsl,pins: three integers array, represents a group of pins mux and config setting. The format is fsl,pins = . PIN is an integer between 0 and 0xbf. imx27 has 6 ports with 32 configurable configurable pins each. PIN is PORT * 32 + PORT_PIN, PORT_PIN is the pin number on the specific port (between 0 and 31). MUX_ID is function + (direction << 2) + (gpio_oconf << 4) + (gpio_iconfa << 8) + (gpio_iconfb << 10) function value is used to select the pin function. Possible values: 0 - Primary function 1 - Alternate function 2 - GPIO Registers: GIUS (GPIO In Use), GPR (General Purpose Register) direction defines the data direction of the pin. Possible values: 0 - Input 1 - Output Register: DDIR gpio_oconf configures the gpio submodule output signal. This does not have any effect unless GPIO function is selected. A/B/C_IN are output signals of function blocks A,B and C. Specific function blocks are described in the reference manual. Possible values: 0 - A_IN 1 - B_IN 2 - C_IN 3 - Data Register Registers: OCR1, OCR2 gpio_iconfa/b configures the gpio submodule input to functionblocks A and B. GPIO function should be selected if this is configured. Possible values: 0 - GPIO_IN 1 - Interrupt Status Register 2 - Pulldown 3 - Pullup Registers ICONFA1, ICONFA2, ICONFB1 and ICONFB2 CONFIG can be 0 or 1, meaning Pullup disable/enable. The iomux controller has gpio child nodes which are embedded in the iomux control registers. They have to be defined as child nodes of the iomux device node. If gpio subnodes are defined "#address-cells", "#size-cells" and "ranges" properties for the iomux device node are required. Example: iomuxc: iomuxc@10015000 { compatible = "fsl,imx27-iomuxc"; reg = <0x10015000 0x600>; #address-cells = <1>; #size-cells = <1>; ranges; gpio1: gpio@10015000 { ... }; ... uart { pinctrl_uart1: uart-1 { fsl,pins = < 0x8c 0x004 0x0 /* UART1_TXD__UART1_TXD */ 0x8d 0x000 0x0 /* UART1_RXD__UART1_RXD */ 0x8e 0x004 0x0 /* UART1_CTS__UART1_CTS */ 0x8f 0x000 0x0 /* UART1_RTS__UART1_RTS */ >; }; ... }; }; For convenience there are macros defined in imx27-pinfunc.h which provide PIN and MUX_ID. They are structured as MX27_PAD___. The names are defined in the i.MX27 reference manual. The above example using macros: iomuxc: iomuxc@10015000 { compatible = "fsl,imx27-iomuxc"; reg = <0x10015000 0x600>; #address-cells = <1>; #size-cells = <1>; ranges; gpio1: gpio@10015000 { ... }; ... uart { pinctrl_uart1: uart-1 { fsl,pins = < MX27_PAD_UART1_TXD__UART1_TXD 0x0 MX27_PAD_UART1_RXD__UART1_RXD 0x0 MX27_PAD_UART1_CTS__UART1_CTS 0x0 MX27_PAD_UART1_RTS__UART1_RTS 0x0 >; }; ... }; };