Regulator DT binding for MAX77620 Power management IC from Maxim Semiconductor. Device has multiple DCDC(sd[0-3] and LDOs(ldo[0-8]). The input supply of these regulators are defined under parent device node. Details of regulator properties are defined as child node under sub-node "regulators" which is child node of device node. Please refer file for common regulator bindings used by client. Following are properties of parent node related to regulators. Optional properties: ------------------- The input supply of regulators are the optional properties on the parent device node. The input supply of these regulators are provided through following properties: in-sd0-supply: Input supply for SD0, INA-SD0 or INB-SD0 pins. in-sd1-supply: Input supply for SD1. in-sd2-supply: Input supply for SD2. in-sd3-supply: Input supply for SD3. in-ldo0-1-supply: Input supply for LDO0 and LDO1. in-ldo2-supply: Input supply for LDO2. in-ldo3-5-supply: Input supply for LDO3 and LDO5 in-ldo4-6-supply: Input supply for LDO4 and LDO6. in-ldo7-8-supply: Input supply for LDO7 and LDO8. Optional sub nodes for regulators under "regulators" subnode: ------------------------------------------------------------ The subnodes name is the name of regulator and it must be one of: sd[0-3], ldo[0-8] Each sub-node should contain the constraints and initialization information for that regulator. The definition for each of these nodes is defined using the standard binding for regulators found at . There are also additional properties for SD/LDOs. These additional properties are required to configure FPS configuration parameters for SDs and LDOs. Please refer for more detail of Flexible Power Sequence (FPS). Following are additional properties: - maxim,active-fps-source: FPS source for the regulators to get enabled/disabled when system is in active state. Valid values are: - MAX77620_FPS_SRC_0, FPS source is FPS0. - MAX77620_FPS_SRC_1, FPS source is FPS1 - MAX77620_FPS_SRC_2 and FPS source is FPS2 - MAX77620_FPS_SRC_NONE. Regulator is not controlled by FPS events and it gets enabled/disabled by register access. Absence of this property will leave the FPS configuration register for that regulator to default configuration. - maxim,active-fps-power-up-slot: Sequencing event slot number on which the regulator get enabled when master FPS input event set to HIGH. Valid values are 0 to 7. This is applicable if FPS source is selected as FPS0, FPS1 or FPS2. - maxim,active-fps-power-down-slot: Sequencing event slot number on which the regulator get disabled when master FPS input event set to LOW. Valid values are 0 to 7. This is applicable if FPS source is selected as FPS0, FPS1 or FPS2. - maxim,suspend-fps-source: This is same as property "maxim,active-fps-source" but value get configured when system enters in to suspend state. - maxim,suspend-fps-power-up-slot: This is same as property "maxim,active-fps-power-up-slot" but this value get configured into FPS configuration register when system enters into suspend. This is applicable if suspend state FPS source is selected as FPS0, FPS1 or - maxim,suspend-fps-power-down-slot: This is same as property "maxim,active-fps-power-down-slot" but this value get configured into FPS configuration register when system enters into suspend. This is applicable if suspend state FPS source is selected as FPS0, FPS1 or FPS2. - maxim,ramp-rate-setting: integer, ramp rate(uV/us) setting to be configured to the device. The platform may have different ramp rate than advertised ramp rate if it has design variation from Maxim's recommended. On this case, platform specific ramp rate is used for ramp time calculation and this property is used for device register configurations. The measured ramp rate of platform is provided by the regulator-ramp-delay as described in . Maxim Max77620 supports following ramp delay: SD: 13.75mV/us, 27.5mV/us, 55mV/us LDOs: 5mV/us, 100mV/us Note: If the measured ramp delay is same as advertised ramp delay then it is not required to provide the ramp delay with property "maxim,ramp-rate-setting". The ramp rate can be provided by the regulator-ramp-delay which will be used for ramp time calculation for voltage change as well as for device configuration. Example: -------- #include ... max77620@3c { in-ldo0-1-supply = <&max77620_sd2>; in-ldo7-8-supply = <&max77620_sd2>; regulators { sd0 { regulator-name = "vdd-core"; regulator-min-microvolt = <600000>; regulator-max-microvolt = <1400000>; regulator-boot-on; regulator-always-on; maxim,active-fps-source = ; }; sd1 { regulator-name = "vddio-ddr"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-always-on; regulator-boot-on; maxim,active-fps-source = ; }; sd2 { regulator-name = "vdd-pre-reg"; regulator-min-microvolt = <1350000>; regulator-max-microvolt = <1350000>; }; sd3 { regulator-name = "vdd-1v8"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on; }; ldo0 { regulator-name = "avdd-sys"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-always-on; regulator-boot-on; }; ldo1 { regulator-name = "vdd-pex"; regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; }; ldo2 { regulator-name = "vddio-sdmmc3"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; }; ldo3 { regulator-name = "vdd-cam-hv"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; }; ldo4 { regulator-name = "vdd-rtc"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <1250000>; regulator-always-on; regulator-boot-on; }; ldo5 { regulator-name = "avdd-ts-hv"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; }; ldo6 { regulator-name = "vdd-ts"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on; }; ldo7 { regulator-name = "vdd-gen-pll-edp"; regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; regulator-always-on; regulator-boot-on; }; ldo8 { regulator-name = "vdd-hdmi-dp"; regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; }; }; };