blob: 6a162f81f6801ec211ca6eb02cd20d76fea64519 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
|
menuconfig NAND
bool "NAND support"
help
This enables support for accessing all type of NAND flash
devices. For further information see
<http://www.linux-mtd.infradead.org/doc/nand.html>.
if NAND
config MTD_NAND_ECC_SW_BCH
select BCH
bool
prompt "Support software BCH ecc"
config NAND_ALLOW_ERASE_BAD
bool
depends on MTD_WRITE
prompt "Add device parameter to allow erasing bad blocks"
help
This adds a 'erasebad' device parameter to nand devices. When set
to '1' it will be allowed to erase bad blocks. This is a potientially
dangerous operation, so if unsure say no to this option.
config NAND_IMX
bool
prompt "i.MX NAND driver"
depends on ARCH_IMX
config NAND_MXS
bool
select NAND_BBT
select STMP_DEVICE
prompt "i.MX23/28/6 NAND driver"
depends on MXS_APBH_DMA
config NAND_OMAP_GPMC
tristate "NAND Flash Support for GPMC based OMAP platforms"
depends on OMAP_GPMC
help
Support for NAND flash using GPMC. GPMC is a common memory
interface found on Texas Instrument's OMAP platforms
config MTD_NAND_OMAP_ELM
bool "Support for ELM (Error Location Module) on OMAP platforms"
depends on NAND_OMAP_GPMC || COMPILE_TEST
help
This config enables the ELM hardware engine, which can be used to
locate and correct errors when using BCH ECC scheme. This offloads
the cpu from doing ECC error searching and correction. However some
legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine
so this is optional for them.
config NAND_ORION
bool
prompt "Marvell Orion NAND driver"
depends on ARM && (ARCH_KIRKWOOD || COMPILE_TEST)
help
Support for the Orion NAND controller, present in Kirkwood SoCs.
config NAND_MRVL_NFC
bool
prompt "Marvell PXA3xx NAND driver"
depends on ARCH_ARMADA_370 || ARCH_ARMADA_XP || ARCH_PXA3XX || COMPILE_TEST
help
Support for the PXA3xx NAND controller, present in Armada 370/XP and
PXA3xx SoCs.
config NAND_ATMEL
bool
prompt "Atmel (AT91SAM9xxx) NAND driver"
depends on ARCH_AT91
config NAND_ATMEL_PMECC
bool
prompt "PMECC support"
depends on NAND_ATMEL || COMPILE_TEST
help
Support for PMECC present on the SoC sam9x5 and sam9n12
config NAND_S3C24XX
bool
prompt "Samsung S3C24XX NAND driver"
depends on ARCH_S3C24xx
help
Add support for processor's NAND device controller.
config MTD_NAND_ECC_SW_HAMMING_SMC
bool "NAND ECC Smart Media byte order"
default n
help
Software ECC according to the Smart Media Specification.
The original Linux implementation had byte 0 and 1 swapped.
config MTD_NAND_NOMADIK
tristate "ST Nomadik 8815 NAND support"
depends on ARCH_NOMADIK
help
Driver for the NAND flash controller on the Nomadik, with ECC.
config MTD_NAND_DENALI
tristate "Support Denali NAND controller"
depends on HAS_DMA
help
Enable support for the Denali NAND controller. This should be
combined with either the PCI or platform drivers to provide device
registration.
config MTD_NAND_DENALI_DT
tristate "Support Denali NAND controller as a DT device"
depends on HAVE_CLK && MTD_NAND_DENALI
help
Enable the driver for NAND flash on platforms using a Denali NAND
controller as a DT device.
if MTD_NAND_DENALI
config MTD_NAND_DENALI_TIMING_MODE
int "Overrides default ONFI timing mode."
default -1
range -1 5
help
-1 indicates use default timings
endif
endif
|
