1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/memory-controllers/st,stm32-fmc2-ebi.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: STMicroelectronics Flexible Memory Controller 2 (FMC2) Bindings
description: |
The FMC2 functional block makes the interface with: synchronous and
asynchronous static devices (such as PSNOR, PSRAM or other memory-mapped
peripherals) and NAND flash memories.
Its main purposes are:
- to translate AXI transactions into the appropriate external device
protocol
- to meet the access time requirements of the external devices
All external devices share the addresses, data and control signals with the
controller. Each external device is accessed by means of a unique Chip
Select. The FMC2 performs only one access at a time to an external device.
maintainers:
- Christophe Kerello <christophe.kerello@st.com>
properties:
compatible:
const: st,stm32mp1-fmc2-ebi
reg:
maxItems: 1
clocks:
maxItems: 1
resets:
maxItems: 1
"#address-cells":
const: 2
"#size-cells":
const: 1
ranges:
description: |
Reflects the memory layout with four integer values per bank. Format:
<bank-number> 0 <address of the bank> <size>
patternProperties:
"^.*@[0-4],[a-f0-9]+$":
type: object
properties:
reg:
description: Bank number, base address and size of the device.
st,fmc2-ebi-cs-transaction-type:
description: |
Select one of the transactions type supported
0: Asynchronous mode 1 SRAM/FRAM.
1: Asynchronous mode 1 PSRAM.
2: Asynchronous mode A SRAM/FRAM.
3: Asynchronous mode A PSRAM.
4: Asynchronous mode 2 NOR.
5: Asynchronous mode B NOR.
6: Asynchronous mode C NOR.
7: Asynchronous mode D NOR.
8: Synchronous read synchronous write PSRAM.
9: Synchronous read asynchronous write PSRAM.
10: Synchronous read synchronous write NOR.
11: Synchronous read asynchronous write NOR.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 11
st,fmc2-ebi-cs-cclk-enable:
description: Continuous clock enable (first bank must be configured
in synchronous mode). The FMC_CLK is generated continuously
during asynchronous and synchronous access. By default, the
FMC_CLK is only generated during synchronous access.
$ref: /schemas/types.yaml#/definitions/flag
st,fmc2-ebi-cs-mux-enable:
description: Address/Data multiplexed on databus (valid only with
NOR and PSRAM transactions type). By default, Address/Data
are not multiplexed.
$ref: /schemas/types.yaml#/definitions/flag
st,fmc2-ebi-cs-buswidth:
description: Data bus width
$ref: /schemas/types.yaml#/definitions/uint32
enum: [ 8, 16 ]
default: 16
st,fmc2-ebi-cs-waitpol-high:
description: Wait signal polarity (NWAIT signal active high).
By default, NWAIT is active low.
$ref: /schemas/types.yaml#/definitions/flag
st,fmc2-ebi-cs-waitcfg-enable:
description: The NWAIT signal indicates wheither the data from the
device are valid or if a wait state must be inserted when accessing
the device in synchronous mode. By default, the NWAIT signal is
active one data cycle before wait state.
$ref: /schemas/types.yaml#/definitions/flag
st,fmc2-ebi-cs-wait-enable:
description: The NWAIT signal is enabled (its level is taken into
account after the programmed latency period to insert wait states
if asserted). By default, the NWAIT signal is disabled.
$ref: /schemas/types.yaml#/definitions/flag
st,fmc2-ebi-cs-asyncwait-enable:
description: The NWAIT signal is taken into account during asynchronous
transactions. By default, the NWAIT signal is not taken into account
during asynchronous transactions.
$ref: /schemas/types.yaml#/definitions/flag
st,fmc2-ebi-cs-cpsize:
description: CRAM page size. The controller splits the burst access
when the memory page is reached. By default, no burst split when
crossing page boundary.
$ref: /schemas/types.yaml#/definitions/uint32
enum: [ 0, 128, 256, 512, 1024 ]
default: 0
st,fmc2-ebi-cs-byte-lane-setup-ns:
description: This property configures the byte lane setup timing
defined in nanoseconds from NBLx low to Chip Select NEx low.
st,fmc2-ebi-cs-address-setup-ns:
description: This property defines the duration of the address setup
phase in nanoseconds used for asynchronous read/write transactions.
st,fmc2-ebi-cs-address-hold-ns:
description: This property defines the duration of the address hold
phase in nanoseconds used for asynchronous multiplexed read/write
transactions.
st,fmc2-ebi-cs-data-setup-ns:
description: This property defines the duration of the data setup phase
in nanoseconds used for asynchronous read/write transactions.
st,fmc2-ebi-cs-bus-turnaround-ns:
description: This property defines the delay in nanoseconds between the
end of current read/write transaction and the next transaction.
st,fmc2-ebi-cs-data-hold-ns:
description: This property defines the duration of the data hold phase
in nanoseconds used for asynchronous read/write transactions.
st,fmc2-ebi-cs-clk-period-ns:
description: This property defines the FMC_CLK output signal period in
nanoseconds.
st,fmc2-ebi-cs-data-latency-ns:
description: This property defines the data latency before reading or
writing the first data in nanoseconds.
st,fmc2_ebi-cs-write-address-setup-ns:
description: This property defines the duration of the address setup
phase in nanoseconds used for asynchronous write transactions.
st,fmc2-ebi-cs-write-address-hold-ns:
description: This property defines the duration of the address hold
phase in nanoseconds used for asynchronous multiplexed write
transactions.
st,fmc2-ebi-cs-write-data-setup-ns:
description: This property defines the duration of the data setup
phase in nanoseconds used for asynchronous write transactions.
st,fmc2-ebi-cs-write-bus-turnaround-ns:
description: This property defines the delay between the end of current
write transaction and the next transaction in nanoseconds.
st,fmc2-ebi-cs-write-data-hold-ns:
description: This property defines the duration of the data hold phase
in nanoseconds used for asynchronous write transactions.
st,fmc2-ebi-cs-max-low-pulse-ns:
description: This property defines the maximum chip select low pulse
duration in nanoseconds for synchronous transactions. When this timing
reaches 0, the controller splits the current access, toggles NE to
allow device refresh and restarts a new access.
required:
- reg
required:
- "#address-cells"
- "#size-cells"
- compatible
- reg
- clocks
- ranges
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/stm32mp1-clks.h>
#include <dt-bindings/reset/stm32mp1-resets.h>
memory-controller@58002000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "st,stm32mp1-fmc2-ebi";
reg = <0x58002000 0x1000>;
clocks = <&rcc FMC_K>;
resets = <&rcc FMC_R>;
ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
<1 0 0x64000000 0x04000000>, /* EBI CS 2 */
<2 0 0x68000000 0x04000000>, /* EBI CS 3 */
<3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
<4 0 0x80000000 0x10000000>; /* NAND */
psram@0,0 {
compatible = "mtd-ram";
reg = <0 0x00000000 0x100000>;
bank-width = <2>;
st,fmc2-ebi-cs-transaction-type = <1>;
st,fmc2-ebi-cs-address-setup-ns = <60>;
st,fmc2-ebi-cs-data-setup-ns = <30>;
st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
};
nand-controller@4,0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32mp1-fmc2-nfc";
reg = <4 0x00000000 0x1000>,
<4 0x08010000 0x1000>,
<4 0x08020000 0x1000>,
<4 0x01000000 0x1000>,
<4 0x09010000 0x1000>,
<4 0x09020000 0x1000>;
interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>,
<&mdma1 20 0x2 0x12000a08 0x0 0x0>,
<&mdma1 21 0x2 0x12000a0a 0x0 0x0>;
dma-names = "tx", "rx", "ecc";
nand@0 {
reg = <0>;
nand-on-flash-bbt;
#address-cells = <1>;
#size-cells = <1>;
};
};
};
...
|
