summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/pci/mediatek-pcie.txt
blob: 57ae7346227238ae73fb47d265b2aec2b24da314 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
MediaTek Gen2 PCIe controller

Required properties:
- compatible: Should contain one of the following strings:
	"mediatek,mt2701-pcie"
	"mediatek,mt2712-pcie"
	"mediatek,mt7622-pcie"
	"mediatek,mt7623-pcie"
	"mediatek,mt7629-pcie"
- device_type: Must be "pci"
- reg: Base addresses and lengths of the root ports.
- reg-names: Names of the above areas to use during resource lookup.
- #address-cells: Address representation for root ports (must be 3)
- #size-cells: Size representation for root ports (must be 2)
- clocks: Must contain an entry for each entry in clock-names.
  See ../clocks/clock-bindings.txt for details.
- clock-names:
  Mandatory entries:
   - sys_ckN :transaction layer and data link layer clock
  Required entries for MT2701/MT7623:
   - free_ck :for reference clock of PCIe subsys
  Required entries for MT2712/MT7622:
   - ahb_ckN :AHB slave interface operating clock for CSR access and RC
	      initiated MMIO access
  Required entries for MT7622:
   - axi_ckN :application layer MMIO channel operating clock
   - aux_ckN :pe2_mac_bridge and pe2_mac_core operating clock when
	      pcie_mac_ck/pcie_pipe_ck is turned off
   - obff_ckN :OBFF functional block operating clock
   - pipe_ckN :LTSSM and PHY/MAC layer operating clock
  where N starting from 0 to one less than the number of root ports.
- phys: List of PHY specifiers (used by generic PHY framework).
- phy-names : Must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
  number of PHYs as specified in *phys* property.
- power-domains: A phandle and power domain specifier pair to the power domain
  which is responsible for collapsing and restoring power to the peripheral.
- bus-range: Range of bus numbers associated with this controller.
- ranges: Ranges for the PCI memory and I/O regions.

Required properties for MT7623/MT2701:
- #interrupt-cells: Size representation for interrupts (must be 1)
- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
  Please refer to the standard PCI bus binding document for a more detailed
  explanation.
- resets: Must contain an entry for each entry in reset-names.
  See ../reset/reset.txt for details.
- reset-names: Must be "pcie-rst0", "pcie-rst1", "pcie-rstN".. based on the
  number of root ports.

Required properties for MT2712/MT7622/MT7629:
-interrupts: A list of interrupt outputs of the controller, must have one
	     entry for each PCIe port
- interrupt-names: Must include the following entries:
	- "pcie_irq": The interrupt that is asserted when an MSI/INTX is received
- linux,pci-domain: PCI domain ID. Should be unique for each host controller

In addition, the device tree node must have sub-nodes describing each
PCIe port interface, having the following mandatory properties:

Required properties:
- device_type: Must be "pci"
- reg: Only the first four bytes are used to refer to the correct bus number
  and device number.
- #address-cells: Must be 3
- #size-cells: Must be 2
- #interrupt-cells: Must be 1
- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
  Please refer to the standard PCI bus binding document for a more detailed
  explanation.
- ranges: Sub-ranges distributed from the PCIe controller node. An empty
  property is sufficient.

Examples for MT7623:

	hifsys: syscon@1a000000 {
		compatible = "mediatek,mt7623-hifsys",
			     "mediatek,mt2701-hifsys",
			     "syscon";
		reg = <0 0x1a000000 0 0x1000>;
		#clock-cells = <1>;
		#reset-cells = <1>;
	};

	pcie: pcie@1a140000 {
		compatible = "mediatek,mt7623-pcie";
		device_type = "pci";
		reg = <0 0x1a140000 0 0x1000>, /* PCIe shared registers */
		      <0 0x1a142000 0 0x1000>, /* Port0 registers */
		      <0 0x1a143000 0 0x1000>, /* Port1 registers */
		      <0 0x1a144000 0 0x1000>; /* Port2 registers */
		reg-names = "subsys", "port0", "port1", "port2";
		#address-cells = <3>;
		#size-cells = <2>;
		#interrupt-cells = <1>;
		interrupt-map-mask = <0xf800 0 0 0>;
		interrupt-map = <0x0000 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>,
				<0x0800 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>,
				<0x1000 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
		clocks = <&topckgen CLK_TOP_ETHIF_SEL>,
			 <&hifsys CLK_HIFSYS_PCIE0>,
			 <&hifsys CLK_HIFSYS_PCIE1>,
			 <&hifsys CLK_HIFSYS_PCIE2>;
		clock-names = "free_ck", "sys_ck0", "sys_ck1", "sys_ck2";
		resets = <&hifsys MT2701_HIFSYS_PCIE0_RST>,
			 <&hifsys MT2701_HIFSYS_PCIE1_RST>,
			 <&hifsys MT2701_HIFSYS_PCIE2_RST>;
		reset-names = "pcie-rst0", "pcie-rst1", "pcie-rst2";
		phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>,
		       <&pcie2_phy PHY_TYPE_PCIE>;
		phy-names = "pcie-phy0", "pcie-phy1", "pcie-phy2";
		power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>;
		bus-range = <0x00 0xff>;
		ranges = <0x81000000 0 0x1a160000 0 0x1a160000 0 0x00010000	/* I/O space */
			  0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>;	/* memory space */

		pcie@0,0 {
			reg = <0x0000 0 0 0 0>;
			#address-cells = <3>;
			#size-cells = <2>;
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0>;
			interrupt-map = <0 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>;
			ranges;
		};

		pcie@1,0 {
			reg = <0x0800 0 0 0 0>;
			#address-cells = <3>;
			#size-cells = <2>;
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0>;
			interrupt-map = <0 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
			ranges;
		};

		pcie@2,0 {
			reg = <0x1000 0 0 0 0>;
			#address-cells = <3>;
			#size-cells = <2>;
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0>;
			interrupt-map = <0 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
			ranges;
		};
	};

Examples for MT2712:

	pcie1: pcie@112ff000 {
		compatible = "mediatek,mt2712-pcie";
		device_type = "pci";
		reg = <0 0x112ff000 0 0x1000>;
		reg-names = "port1";
		linux,pci-domain = <1>;
		#address-cells = <3>;
		#size-cells = <2>;
		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-names = "pcie_irq";
		clocks = <&topckgen CLK_TOP_PE2_MAC_P1_SEL>,
			 <&pericfg CLK_PERI_PCIE1>;
		clock-names = "sys_ck1", "ahb_ck1";
		phys = <&u3port1 PHY_TYPE_PCIE>;
		phy-names = "pcie-phy1";
		bus-range = <0x00 0xff>;
		ranges = <0x82000000 0 0x11400000  0x0 0x11400000  0 0x300000>;
		status = "disabled";

		#interrupt-cells = <1>;
		interrupt-map-mask = <0 0 0 7>;
		interrupt-map = <0 0 0 1 &pcie_intc1 0>,
				<0 0 0 2 &pcie_intc1 1>,
				<0 0 0 3 &pcie_intc1 2>,
				<0 0 0 4 &pcie_intc1 3>;
		pcie_intc1: interrupt-controller {
			interrupt-controller;
			#address-cells = <0>;
			#interrupt-cells = <1>;
		};
	};

	pcie0: pcie@11700000 {
		compatible = "mediatek,mt2712-pcie";
		device_type = "pci";
		reg = <0 0x11700000 0 0x1000>;
		reg-names = "port0";
		linux,pci-domain = <0>;
		#address-cells = <3>;
		#size-cells = <2>;
		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-names = "pcie_irq";
		clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>,
			 <&pericfg CLK_PERI_PCIE0>;
		clock-names = "sys_ck0", "ahb_ck0";
		phys = <&u3port0 PHY_TYPE_PCIE>;
		phy-names = "pcie-phy0";
		bus-range = <0x00 0xff>;
		ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>;
		status = "disabled";

		#interrupt-cells = <1>;
		interrupt-map-mask = <0 0 0 7>;
		interrupt-map = <0 0 0 1 &pcie_intc0 0>,
				<0 0 0 2 &pcie_intc0 1>,
				<0 0 0 3 &pcie_intc0 2>,
				<0 0 0 4 &pcie_intc0 3>;
		pcie_intc0: interrupt-controller {
			interrupt-controller;
			#address-cells = <0>;
			#interrupt-cells = <1>;
		};
	};

Examples for MT7622:

	pcie0: pcie@1a143000 {
		compatible = "mediatek,mt7622-pcie";
		device_type = "pci";
		reg = <0 0x1a143000 0 0x1000>;
		reg-names = "port0";
		linux,pci-domain = <0>;
		#address-cells = <3>;
		#size-cells = <2>;
		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>;
		interrupt-names = "pcie_irq";
		clocks = <&pciesys CLK_PCIE_P0_MAC_EN>,
			 <&pciesys CLK_PCIE_P0_AHB_EN>,
			 <&pciesys CLK_PCIE_P0_AUX_EN>,
			 <&pciesys CLK_PCIE_P0_AXI_EN>,
			 <&pciesys CLK_PCIE_P0_OBFF_EN>,
			 <&pciesys CLK_PCIE_P0_PIPE_EN>;
		clock-names = "sys_ck0", "ahb_ck0", "aux_ck0",
			      "axi_ck0", "obff_ck0", "pipe_ck0";

		power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
		bus-range = <0x00 0xff>;
		ranges = <0x82000000 0 0x20000000  0x0 0x20000000  0 0x8000000>;
		status = "disabled";

		#interrupt-cells = <1>;
		interrupt-map-mask = <0 0 0 7>;
		interrupt-map = <0 0 0 1 &pcie_intc0 0>,
				<0 0 0 2 &pcie_intc0 1>,
				<0 0 0 3 &pcie_intc0 2>,
				<0 0 0 4 &pcie_intc0 3>;
		pcie_intc0: interrupt-controller {
			interrupt-controller;
			#address-cells = <0>;
			#interrupt-cells = <1>;
		};
	};

	pcie1: pcie@1a145000 {
		compatible = "mediatek,mt7622-pcie";
		device_type = "pci";
		reg = <0 0x1a145000 0 0x1000>;
		reg-names = "port1";
		linux,pci-domain = <1>;
		#address-cells = <3>;
		#size-cells = <2>;
		interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
		interrupt-names = "pcie_irq";
		clocks = <&pciesys CLK_PCIE_P1_MAC_EN>,
			 /* designer has connect RC1 with p0_ahb clock */
			 <&pciesys CLK_PCIE_P0_AHB_EN>,
			 <&pciesys CLK_PCIE_P1_AUX_EN>,
			 <&pciesys CLK_PCIE_P1_AXI_EN>,
			 <&pciesys CLK_PCIE_P1_OBFF_EN>,
			 <&pciesys CLK_PCIE_P1_PIPE_EN>;
		clock-names = "sys_ck1", "ahb_ck1", "aux_ck1",
			      "axi_ck1", "obff_ck1", "pipe_ck1";

		power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
		bus-range = <0x00 0xff>;
		ranges = <0x82000000 0 0x28000000  0x0 0x28000000  0 0x8000000>;
		status = "disabled";

		#interrupt-cells = <1>;
		interrupt-map-mask = <0 0 0 7>;
		interrupt-map = <0 0 0 1 &pcie_intc1 0>,
				<0 0 0 2 &pcie_intc1 1>,
				<0 0 0 3 &pcie_intc1 2>,
				<0 0 0 4 &pcie_intc1 3>;
		pcie_intc1: interrupt-controller {
			interrupt-controller;
			#address-cells = <0>;
			#interrupt-cells = <1>;
		};
	};