1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/pinctrl/mediatek,mt6779-pinctrl.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: MediaTek MT6779 Pin Controller
maintainers:
- Andy Teng <andy.teng@mediatek.com>
- Sean Wang <sean.wang@kernel.org>
description:
The MediaTek pin controller on MT6779 is used to control pin functions, pull
up/down resistance and drive strength options.
properties:
compatible:
enum:
- mediatek,mt6779-pinctrl
- mediatek,mt6797-pinctrl
reg:
description: Physical addresses for GPIO base(s) and EINT registers.
reg-names: true
gpio-controller: true
"#gpio-cells":
const: 2
description:
Number of cells in GPIO specifier. Since the generic GPIO binding is used,
the amount of cells must be specified as 2. See the below mentioned gpio
binding representation for description of particular cells.
gpio-ranges:
minItems: 1
maxItems: 5
description:
GPIO valid number range.
interrupt-controller: true
interrupts:
maxItems: 1
description:
Specifies the summary IRQ.
"#interrupt-cells":
const: 2
required:
- compatible
- reg
- reg-names
- gpio-controller
- "#gpio-cells"
allOf:
- $ref: pinctrl.yaml#
- if:
properties:
compatible:
contains:
const: mediatek,mt6779-pinctrl
then:
properties:
reg:
minItems: 9
maxItems: 9
reg-names:
items:
- const: gpio
- const: iocfg_rm
- const: iocfg_br
- const: iocfg_lm
- const: iocfg_lb
- const: iocfg_rt
- const: iocfg_lt
- const: iocfg_tl
- const: eint
- if:
properties:
compatible:
contains:
const: mediatek,mt6797-pinctrl
then:
properties:
reg:
minItems: 5
maxItems: 5
reg-names:
items:
- const: gpio
- const: iocfgl
- const: iocfgb
- const: iocfgr
- const: iocfgt
- if:
properties:
reg-names:
contains:
const: eint
then:
required:
- interrupts
- interrupt-controller
- "#interrupt-cells"
patternProperties:
'-[0-9]*$':
type: object
additionalProperties: false
patternProperties:
'-pins*$':
type: object
description:
A pinctrl node should contain at least one subnodes representing the
pinctrl groups available on the machine. Each subnode will list the
pins it needs, and how they should be configured, with regard to muxer
configuration, pullups, drive strength, input enable/disable and input
schmitt.
$ref: /schemas/pinctrl/pincfg-node.yaml
properties:
pinmux:
description:
Integer array, represents gpio pin number and mux setting.
Supported pin number and mux varies for different SoCs, and are
defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly.
bias-disable: true
bias-pull-up: true
bias-pull-down: true
input-enable: true
input-disable: true
output-low: true
output-high: true
input-schmitt-enable: true
input-schmitt-disable: true
drive-strength:
enum: [2, 4, 8, 12, 16]
slew-rate:
enum: [0, 1]
mediatek,pull-up-adv:
description: |
Pull up settings for 2 pull resistors, R0 and R1. User can
configure those special pins. Valid arguments are described as
below:
0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1, 2, 3]
mediatek,pull-down-adv:
description: |
Pull down settings for 2 pull resistors, R0 and R1. User can
configure those special pins. Valid arguments are described as
below:
0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1, 2, 3]
required:
- pinmux
additionalProperties: false
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/mt6779-pinfunc.h>
soc {
#address-cells = <2>;
#size-cells = <2>;
pio: pinctrl@10005000 {
compatible = "mediatek,mt6779-pinctrl";
reg = <0 0x10005000 0 0x1000>,
<0 0x11c20000 0 0x1000>,
<0 0x11d10000 0 0x1000>,
<0 0x11e20000 0 0x1000>,
<0 0x11e70000 0 0x1000>,
<0 0x11ea0000 0 0x1000>,
<0 0x11f20000 0 0x1000>,
<0 0x11f30000 0 0x1000>,
<0 0x1000b000 0 0x1000>;
reg-names = "gpio", "iocfg_rm",
"iocfg_br", "iocfg_lm",
"iocfg_lb", "iocfg_rt",
"iocfg_lt", "iocfg_tl",
"eint";
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&pio 0 0 210>;
interrupt-controller;
#interrupt-cells = <2>;
interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>;
mmc0_pins_default: mmc0-0 {
cmd-dat-pins {
pinmux = <PINMUX_GPIO168__FUNC_MSDC0_DAT0>,
<PINMUX_GPIO172__FUNC_MSDC0_DAT1>,
<PINMUX_GPIO169__FUNC_MSDC0_DAT2>,
<PINMUX_GPIO177__FUNC_MSDC0_DAT3>,
<PINMUX_GPIO170__FUNC_MSDC0_DAT4>,
<PINMUX_GPIO173__FUNC_MSDC0_DAT5>,
<PINMUX_GPIO171__FUNC_MSDC0_DAT6>,
<PINMUX_GPIO174__FUNC_MSDC0_DAT7>,
<PINMUX_GPIO167__FUNC_MSDC0_CMD>;
input-enable;
mediatek,pull-up-adv = <1>;
};
clk-pins {
pinmux = <PINMUX_GPIO176__FUNC_MSDC0_CLK>;
mediatek,pull-down-adv = <2>;
};
rst-pins {
pinmux = <PINMUX_GPIO178__FUNC_MSDC0_RSTB>;
mediatek,pull-up-adv = <0>;
};
};
};
mmc0 {
pinctrl-0 = <&mmc0_pins_default>;
pinctrl-names = "default";
};
};
|
