summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/pinctrl/qcom,ipq8064-pinctrl.txt
blob: 6e88e91feb1130796dacf610ceb0a6969c5b0b95 (plain) (blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Qualcomm IPQ8064 TLMM block

Required properties:
- compatible: "qcom,ipq8064-pinctrl"
- reg: Should be the base address and length of the TLMM block.
- interrupts: Should be the parent IRQ of the TLMM block.
- interrupt-controller: Marks the device node as an interrupt controller.
- #interrupt-cells: Should be two.
- gpio-controller: Marks the device node as a GPIO controller.
- #gpio-cells : Should be two.
                The first cell is the gpio pin number and the
                second cell is used for optional parameters.

Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
a general description of GPIO and interrupt bindings.

Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the meaning of the
phrase "pin configuration node".

Qualcomm's pin configuration nodes act as a container for an arbitrary number of
subnodes. Each of these subnodes represents some desired configuration for a
pin, a group, or a list of pins or groups. This configuration can include the
mux function to select on those pin(s)/group(s), and various pin configuration
parameters, such as pull-up, drive strength, etc.

The name of each subnode is not important; all subnodes should be enumerated
and processed purely based on their content.

Each subnode only affects those parameters that are explicitly listed. In
other words, a subnode that lists a mux function but no pin configuration
parameters implies no information about any pin configuration parameters.
Similarly, a pin subnode that describes a pullup parameter implies no
information about e.g. the mux function.


The following generic properties as defined in pinctrl-bindings.txt are valid
to specify in a pin configuration subnode:

 pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength,
 output-low, output-high.

Non-empty subnodes must specify the 'pins' property.

Valid values for qcom,pins are:
  gpio0-gpio68
   Supports mux, bias, and drive-strength

  sdc3_clk, sdc3_cmd, sdc3_data
   Supports bias and drive-strength


Valid values for function are:
  mdio, mi2s, pdm, ssbi, spmi, audio_pcm, gpio, gsbi1, gsbi2, gsbi4, gsbi5,
  gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi7, nss_spi, sdc1,
  spdif, nand, tsif1, tsif2, usb_fs_n, usb_fs, usb2_hsic, rgmii2, sata,
  pcie1_rst, pcie1_prsnt, pcie1_pwren_n, pcie1_pwren, pcie1_pwrflt,
  pcie1_clk_req, pcie2_rst, pcie2_prsnt, pcie2_pwren_n, pcie2_pwren,
  pcie2_pwrflt, pcie2_clk_req, pcie3_rst, pcie3_prsnt, pcie3_pwren_n,
  pcie3_pwren, pcie3_pwrflt, pcie3_clk_req, ps_hold

Example:

	pinmux: pinctrl@800000 {
		compatible = "qcom,ipq8064-pinctrl";
		reg = <0x800000 0x4000>;

		gpio-controller;
		#gpio-cells = <2>;
		interrupt-controller;
		#interrupt-cells = <2>;
		interrupts = <0 32 0x4>;

		pinctrl-names = "default";
		pinctrl-0 = <&gsbi5_uart_default>;

		gsbi5_uart_default: gsbi5_uart_default {
			mux {
				pins = "gpio18", "gpio19";
				function = "gsbi5";
			};

			tx {
				pins = "gpio18";
				drive-strength = <4>;
				bias-disable;
			};

			rx {
				pins = "gpio19";
				drive-strength = <2>;
				bias-pull-up;
			};
		};
	};