summaryrefslogtreecommitdiffstats
path: root/dts/src/arm/intel-ixp4xx-reference-design.dtsi
blob: c1d9c49982b33a2330806f04ee27c0e28327408b (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
// SPDX-License-Identifier: ISC
/*
 * Device Tree include file for Intel reference designs for the
 * XScale Network Processors in the IXP 4xx series. Common device
 * set-up for IXDP425, IXCDP1100, KIXRP435 and IXDP465.
 */

/ {
	memory@0 {
		/*
		 * The board supports up to 256 MB of memory. Here we put in
		 * 64 MB and this may be modified by the boot loader.
		 */
		device_type = "memory";
		reg = <0x00000000 0x4000000>;
	};

	chosen {
		bootargs = "console=ttyS0,115200n8";
		stdout-path = "uart0:115200n8";
	};

	aliases {
		serial0 = &uart0;
	};

	i2c {
		compatible = "i2c-gpio";
		sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
		#address-cells = <1>;
		#size-cells = <0>;

		eeprom@50 {
			/*
			 * Philips PCF8582C-2T/03 512byte I2C EEPROM
			 * should behave like an Atmel 24c04.
			 */
			compatible = "atmel,24c04";
			reg = <0x50>;
			pagesize = <16>;
			size = <512>;
			read-only;
		};
	};

	soc {
		bus@c4000000 {
			/* Flash memory defined per-variant */
			nand-controller@3,0 {
				/* Some designs have a NAND on CS3 enable it here if present */
				status = "disabled";

				/*
				 * gen_nand needs to be extended and documented to get
				 * command byte = 1 and address byte = 2 from the device
				 * tree.
				 */
				compatible = "gen_nand";

				/* Expansion bus set-up */
				intel,ixp4xx-eb-t1 = <0>;
				intel,ixp4xx-eb-t2 = <0>;
				intel,ixp4xx-eb-t3 = <1>; // 1 cycle extra strobe phase
				intel,ixp4xx-eb-t4 = <0>;
				intel,ixp4xx-eb-t5 = <0>;
				intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type
				intel,ixp4xx-eb-byte-access-on-halfword = <0>;
				intel,ixp4xx-eb-mux-address-and-data = <0>;
				intel,ixp4xx-eb-ahb-split-transfers = <0>;
				intel,ixp4xx-eb-write-enable = <1>;
				intel,ixp4xx-eb-byte-access = <1>;

				/* 512 bytes memory window */
				reg = <3 0x00000000 0x200>;
				nand-on-flash-bbt;
				nand-ecc-mode = "soft_bch";
				nand-ecc-step-size = <512>;
				nand-ecc-strength = <4>;
				nce-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; /* NCE */

				label = "ixp400 NAND";

				partitions {
					compatible = "fixed-partitions";
					#address-cells = <1>;
					#size-cells = <1>;

					fs@0 {
						label = "ixp400 NAND FS 0";
						reg = <0x0 0x800000>;
					};
					fs@800000 {
						label = "ixp400 NAND FS 1";
						reg = <0x800000 0x0>;
					};
				};
			};
		};

		pci@c0000000 {
			status = "ok";

			/*
			 * Taken from IXDP425 PCI boardfile.
			 * PCI slots on the BIXMB425BD base card.
			 * We have up to 4 slots (IDSEL) with 4 swizzled IRQs.
			 */
			interrupt-map =
			/* IDSEL 1 */
			<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
			<0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */
			<0x0800 0 0 3 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */
			<0x0800 0 0 4 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
			/* IDSEL 2 */
			<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
			<0x1000 0 0 2 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
			<0x1000 0 0 3 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */
			<0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */
			/* IDSEL 3 */
			<0x1800 0 0 1 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */
			<0x1800 0 0 2 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */
			<0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */
			<0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */
			/* IDSEL 4 */
			<0x2000 0 0 1 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 4 is irq 8 */
			<0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 4 is irq 11 */
			<0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 4 is irq 10 */
			<0x2000 0 0 4 &gpio0 9  IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 4 is irq 9 */
		};
	};
};