diff options
Diffstat (limited to 'Documentation/devicetree/bindings/regulator')
4 files changed, 105 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt index c7610718adfff..f9be1acf891c1 100644 --- a/Documentation/devicetree/bindings/regulator/pfuze100.txt +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -12,6 +12,11 @@ Optional properties: disabled. This binding is a workaround to keep backward compatibility with old dtb's which rely on the fact that the switched regulators are always on and don't mark them explicit as "regulator-always-on". +- fsl,pmic-stby-poweroff: if present, configure the PMIC to shutdown all + power rails when PMIC_STBY_REQ line is asserted during the power off sequence. + Use this option if the SoC should be powered off by external power + management IC (PMIC) on PMIC_STBY_REQ signal. + As opposite to PMIC_STBY_REQ boards can implement PMIC_ON_REQ signal. Required child node: - regulators: This is the list of child nodes that specify the regulator diff --git a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt index 58a1d97972f5a..45025b5b67f6b 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt @@ -26,6 +26,7 @@ Regulator nodes are identified by their compatible: "qcom,rpm-pm8998-regulators" "qcom,rpm-pma8084-regulators" "qcom,rpm-pmi8998-regulators" + "qcom,rpm-pms405-regulators" - vdd_s1-supply: - vdd_s2-supply: @@ -188,6 +189,24 @@ Regulator nodes are identified by their compatible: Definition: reference to regulator supplying the input pin, as described in the data sheet +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_l1_l2-supply: +- vdd_l3_l8-supply: +- vdd_l4-supply: +- vdd_l5_l6-supply: +- vdd_l7-supply: +- vdd_l3_l8-supply: +- vdd_l9-supply: +- vdd_l10_l11_l12_l13-supply: + Usage: optional (pms405 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each of the pmics below. @@ -222,6 +241,10 @@ pma8084: pmi8998: bob +pms405: + s1, s2, s3, s4, s5, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, + l13 + The content of each sub-node is defined by the standard binding for regulators - see regulator.txt. diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt index 76ead07072b13..4b98ca26e61a2 100644 --- a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt @@ -1,7 +1,9 @@ -ROHM BD71837 Power Management Integrated Circuit (PMIC) regulator bindings +ROHM BD71837 and BD71847 Power Management Integrated Circuit regulator bindings Required properties: - - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7" + - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7" for + BD71837. For BD71847 names should be "buck1", ..., "buck6" + and "ldo1", ..., "ldo6" List of regulators provided by this controller. BD71837 regulators node should be sub node of the BD71837 MFD node. See BD71837 MFD bindings at @@ -16,10 +18,14 @@ disabled by driver at startup. LDO5 and LDO6 are supplied by those and if they are disabled at startup the voltage monitoring for LDO5/LDO6 will cause PMIC to reset. -The valid names for regulator nodes are: +The valid names for BD71837 regulator nodes are: BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, BUCK7, BUCK8 LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7 +The valid names for BD71847 regulator nodes are: +BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6 +LDO1, LDO2, LDO3, LDO4, LDO5, LDO6 + Optional properties: - Any optional property defined in bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt new file mode 100644 index 0000000000000..a3f4762405655 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt @@ -0,0 +1,68 @@ +STMicroelectronics STPMIC1 Voltage regulators + +Regulator Nodes are optional depending on needs. + +Available Regulators in STPMIC1 device are: + - buck1 for Buck BUCK1 + - buck2 for Buck BUCK2 + - buck3 for Buck BUCK3 + - buck4 for Buck BUCK4 + - ldo1 for LDO LDO1 + - ldo2 for LDO LDO2 + - ldo3 for LDO LDO3 + - ldo4 for LDO LDO4 + - ldo5 for LDO LDO5 + - ldo6 for LDO LDO6 + - vref_ddr for LDO Vref DDR + - boost for Buck BOOST + - pwr_sw1 for VBUS_OTG switch + - pwr_sw2 for SW_OUT switch + +Switches are fixed voltage regulators with only enable/disable capability. + +Optional properties: +- st,mask-reset: mask reset for this regulator: the regulator configuration + is maintained during pmic reset. +- regulator-pull-down: enable high pull down + if not specified light pull down is used +- regulator-over-current-protection: + if set, all regulators are switched off in case of over-current detection + on this regulator, + if not set, the driver only sends an over-current event. +- interrupt-parent: phandle to the parent interrupt controller +- interrupts: index of current limit detection interrupt +- <regulator>-supply: phandle to the parent supply/regulator node + each regulator supply can be described except vref_ddr. + +Example: +regulators { + compatible = "st,stpmic1-regulators"; + + ldo6-supply = <&v3v3>; + + vdd_core: buck1 { + regulator-name = "vdd_core"; + interrupts = <IT_CURLIM_BUCK1 0>; + interrupt-parent = <&pmic>; + st,mask-reset; + regulator-pull-down; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1200000>; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + interrupts = <IT_CURLIM_BUCK4 0>; + interrupt-parent = <&mypmic>; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + v1v8: ldo6 { + regulator-name = "v1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-over-current-protection; + }; +}; |