| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull block fixes from Jens Axboe:
"A small collection of fixes/changes for the current series. This
contains:
- Removal of dead code from Gu Zheng.
- Revert of two bad fixes that went in earlier in this round, marking
things as __init that were not purely used from init.
- A fix for blk_mq_start_hw_queue() using the __blk_mq_run_hw_queue(),
which could place us wrongly. Make it use the non __ variant,
which handles cases where we are called from the wrong CPU set.
From me.
- A fix for drbd, which allocates discard requests without room for
the SCSI payload. From Lars Ellenberg.
- A fix for user-after-free in the blkcg code from Tejun.
- Addition of limiting gaps in SG lists, if the hardware needs it.
This is the last pre-req patch for blk-mq to enable the full NVMe
conversion. Could wait until 3.17, but it's simple enough so would
be nice to have everything we need for the NVMe port in the 3.17
release. From me"
* 'for-linus' of git://git.kernel.dk/linux-block:
drbd: fix NULL pointer deref in blk_add_request_payload
blk-mq: blk_mq_start_hw_queue() should use blk_mq_run_hw_queue()
block: add support for limiting gaps in SG lists
bio: remove unused macro bip_vec_idx()
Revert "block: add __init to elv_register"
Revert "block: add __init to blkcg_policy_register"
blkcg: fix use-after-free in __blkg_release_rcu() by making blkcg_gq refcnt an atomic_t
floppy: format block0 read error message properly
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Discards don't have any payload.
But the scsi layer still expects a bio_vec it can use internally,
see sd_setup_discard_cmnd() and blk_add_request_payload().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| | |\
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/linux-block into for-linus
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
In case reading of block 0 fails, line without trailing newline
is printed causing dmesg to look horrible.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The following check in rbd_img_obj_request_submit()
rbd_dev->parent_overlap <= obj_request->img_offset
allows the fall through to the non-layered write case even if both
parent_overlap and obj_request->img_offset belong to the same RADOS
object. This leads to data corruption, because the area to the left of
parent_overlap ends up unconditionally zero-filled instead of being
populated with parent data. Suppose we want to write 1M to offset 6M
of image bar, which is a clone of foo@snap; object_size is 4M,
parent_overlap is 5M:
rbd_data.<id>.0000000000000001
---------------------|----------------------|------------
| should be copyup'ed | should be zeroed out | write ...
---------------------|----------------------|------------
4M 5M 6M
parent_overlap obj_request->img_offset
4..5M should be copyup'ed from foo, yet it is zero-filled, just like
5..6M is.
Given that the only striping mode kernel client currently supports is
chunking (i.e. stripe_unit == object_size, stripe_count == 1), round
parent_overlap up to the next object boundary for the purposes of the
overlap check.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
|
| |\| |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull block fixes from Jens Axboe:
"A smaller collection of fixes for the block core that would be nice to
have in -rc2. This pull request contains:
- Fixes for races in the wait/wakeup logic used in blk-mq from
Alexander. No issues have been observed, but it is definitely a
bit flakey currently. Alternatively, we may drop the cyclic
wakeups going forward, but that needs more testing.
- Some cleanups from Christoph.
- Fix for an oops in null_blk if queue_mode=1 and softirq completions
are used. From me.
- A fix for a regression caused by the chunk size setting. It
inadvertently used max_hw_sectors instead of max_sectors, which is
incorrect, and causes hangs on btrfs multi-disk setups (where hw
sectors apparently isn't set). From me.
- Removal of WQ_POWER_EFFICIENT in the kblockd creation. This was a
recent addition as well, but it actually breaks blk-mq which relies
on strict scheduling. If the workqueue power_efficient mode is
turned on, this breaks blk-mq. From Matias.
- null_blk module parameter description fix from Mike"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: bitmap tag: fix races in bt_get() function
blk-mq: bitmap tag: fix race on blk_mq_bitmap_tags::wake_cnt
blk-mq: bitmap tag: fix races on shared ::wake_index fields
block: blk_max_size_offset() should check ->max_sectors
null_blk: fix softirq completions for queue_mode == 1
blk-mq: merge blk_mq_drain_queue and __blk_mq_drain_queue
blk-mq: properly drain stopped queues
block: remove WQ_POWER_EFFICIENT from kblockd
null_blk: fix name and description of 'queue_mode' module parameter
block: remove elv_abort_queue and blk_abort_flushes
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Only blk-mq completions have payload attached to the request, for
request_fn mode we have stored it in req->special. This fixes an
oops with queue_mode=1 and softirq completions.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
'use_mq' is not the name of the module parameter, 'queue_mode' is.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Pull NVMe update from Matthew Wilcox:
"Mostly bugfixes again for the NVMe driver. I'd like to call out the
exported tracepoint in the block layer; I believe Keith has cleared
this with Jens.
We've had a few reports from people who're really pounding on NVMe
devices at scale, hence the timeout changes (and new module
parameters), hotplug cpu deadlock, tracepoints, and minor performance
tweaks"
[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
end up going away when mq conversion happens ]
* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
NVMe: Use Log Page constants in SCSI emulation
NVMe: Define Log Page constants
NVMe: Fix hot cpu notification dead lock
NVMe: Rename io_timeout to nvme_io_timeout
NVMe: Use last bytes of f/w rev SCSI Inquiry
NVMe: Adhere to request queue block accounting enable/disable
NVMe: Fix nvme get/put queue semantics
NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
NVMe: Make admin timeout a module parameter
NVMe: Make iod bio timeout a parameter
NVMe: Prevent possible NULL pointer dereference
NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
NVMe: Update data structures for NVMe 1.2
NVMe: Enable BUILD_BUG_ON checks
NVMe: Update namespace and controller identify structures to the 1.1a spec
NVMe: Flush with data support
NVMe: Configure support for block flush
NVMe: Add tracepoints
NVMe: Protect against badly formatted CQEs
...
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch contains several fixes for Scsi START_STOP_UNIT. The previous
code did not account for signed vs. unsigned arithmetic which resulted
in an invalid lowest power state caculation when the device only supports
1 power state.
The code for Power Condition == 2 (Idle) was not following the spec. The
spec calls for setting the device to specific power states, depending
upon Power Condition Modifier, without accounting for the number of
power states supported by the device.
The code for Power Condition == 3 (Standby) was using a hard-coded '0'
which is replaced with the macro POWER_STATE_0.
Signed-off-by: Dan McLeran <daniel.mcleran@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@linux.intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The nvme-scsi file defined its own Log Page constant. Use the
newly-defined one from the header file instead.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
There is a potential dead lock if a cpu event occurs during nvme probe
since it registered with hot cpu notification. This fixes the race by
having the module register with notification outside of probe rather
than have each device register.
The actual work is done in a scheduled work queue instead of in the
notifier since assigning IO queues has the potential to block if the
driver creates additional queues.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
It's positively immoral to have a global variable called 'io_timeout'.
Keep the module parameter called io_timeout, though.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
After skipping right-padded spaces, use the last four bytes of the
firmware revision when reporting the Inquiry Product Revision. These
are generally more indicative to what is running.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Acked-by: Vishal Verma <vishal.l.verma@linux.intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Recently, a new sysfs control "iostats" was added to selectively
enable or disable io statistics collection for request queues. This
patch hooks that control.
IO statistics collection is rather expensive on large, multi-node
machines with drives pushing millions of iops. Having the ability to
disable collection if not needed can improve throughput significantly.
As a data point, on a quad E5-4640, I see more than 50% throughput
improvement when io statistics accounting is disabled during heavily
multi-threaded small block random read benchmarks where device
performance is in the million iops+ range.
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The routines to get and lock nvme queues required the caller to "put"
or "unlock" them even if getting one returned NULL. This patch fixes that.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This define isn't used, and any code that wanted to use it should use
NVME_FEAT_TEMP_THRESH instead.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Keith Busch <keith.busch@intel.com>
[made admin_timeout static]
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This was originally set to 4 times the IO timeout, but that was when
the IO timeout was 5 seconds instead of 30. 20 seconds for total time
to failure seemed more reasonable than 2 minutes for most, but other
users have requested to make this a module parameter instead.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[renamed the module parameter to retry_time]
[made retry_time static]
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
kmalloc() used by the nvme_alloc_iod() to allocate memory for 'iod'
can fail. So check the return value.
Signed-off-by: Santosh Y <santosh.sy@samsung.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
In GetLogPage the buffer size passed to device is a 0's based value.
Signed-off-by: Indraneel M <indraneel.m@samsung.com>
Reported-by: Shiro Itou <shiro.itou@outlook.com>
Reviewed-by: Vishal Verma <vishal.l.verma@linux.intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Since _nvme_check_size() wasn't being called from anywhere, the compiler
was optimising it away ... along with all the link-time build failures
that would result if any of the structures were the wrong size. Call it
from nvme_exit() for no particular reason.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
It is possible a filesystem may send a flush flagged bio with write
data. There is no such composite NVMe command, so the driver sends flush
and write separately.
The device is allowed to execute these commands in any order, so it was
possible the driver ends the bio after the write completes, but while the
flush is still active. We don't want to let a filesystem believe flush
succeeded before it really has; this could cause data corruption on a
power loss between these events. To fix, this patch splits the flush
and write into chained bios.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This configures an nvme request_queue as flush capable if the device
has a volatile write cache present.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Adding tracepoints for bio_complete and block_split into nvme to help
with gathering IO info using blktrace and blkparse.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
If a misbehaving device posts a CQE with a command id < depth but for
one that was never allocated, the command info will have a callback
function set to NULL and we don't want to try invoking that.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Help people diagnose what is going wrong at initialisation time by
printing out which command has gone wrong and what the device returned.
Also fix the error message printed while waiting for reset.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Make the copyright dates accurate and remove the final paragraph that
includes the address of the FSF.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
| |\ \ \ \
| |_|/ /
|/| | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph updates from Sage Weil:
"This has a mix of bug fixes and cleanups.
Alex's patch fixes a rare race in RBD. Ilya's patches fix an ENOENT
check when a second rbd image is mapped and a couple memory leaks.
Zheng fixes several issues with fragmented directories and multiple
MDSs. Josh fixes a spin/sleep issue, and Josh and Guangliang's
patches fix setting and unsetting RBD images read-only.
Naturally there are several other cleanups mixed in for good measure"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (23 commits)
rbd: only set disk to read-only once
rbd: move calls that may sleep out of spin lock range
rbd: add ioctl for rbd
ceph: use truncate_pagecache() instead of truncate_inode_pages()
ceph: include time stamp in every MDS request
rbd: fix ida/idr memory leak
rbd: use reference counts for image requests
rbd: fix osd_request memory leak in __rbd_dev_header_watch_sync()
rbd: make sure we have latest osdmap on 'rbd map'
libceph: add ceph_monc_wait_osdmap()
libceph: mon_get_version request infrastructure
libceph: recognize poolop requests in debugfs
ceph: refactor readpage_nounlock() to make the logic clearer
mds: check cap ID when handling cap export message
ceph: remember subtree root dirfrag's auth MDS
ceph: introduce ceph_fill_fragtree()
ceph: handle cap import atomically
ceph: pre-allocate ceph_cap struct for ceph_add_cap()
ceph: update inode fields according to issued caps
rbd: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
...
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
rbd_open(), called every time the device is opened, calls
set_device_ro(). There's no reason to set the device read-only or
read-write every time it is opened. Just do this once during device
setup, using set_disk_ro() instead because the struct block_device
isn't available to us there.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
get_user() and set_disk_ro() may allocate memory, leading to a
potential deadlock if theye are called while a spin lock is held.
Move the acquisition and release of rbd_dev->lock from rbd_ioctl()
into rbd_ioctl_set_ro(), so it can occur between get_user() and
set_disk_ro().
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When running the following commands:
[root@ceph0 mnt]# blockdev --setro /dev/rbd1
[root@ceph0 mnt]# blockdev --getro /dev/rbd1
0
The block setro didn't take effect, it is because
the rbd doesn't support ioctl of block driver.
This resolves:
http://tracker.ceph.com/issues/6265
Signed-off-by: Guangliang Zhao <guangliang@unitedstack.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
ida_destroy() needs to be called on module exit to release ida caches.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Each image request contains a reference count, but to date it has
not actually been used. (I think this was just an oversight.) A
recent report involving rbd failing an assertion shed light on why
and where we need to use these reference counts.
Every OSD request associated with an object request uses
rbd_osd_req_callback() as its callback function. That function will
call a helper function (dependent on the type of OSD request) that
will set the object request's "done" flag if the object request if
appropriate. If that "done" flag is set, the object request is
passed to rbd_obj_request_complete().
In rbd_obj_request_complete(), requests are processed in sequential
order. So if an object request completes before one of its
predecessors in the image request, the completion is deferred.
Otherwise, if it's a completing object's "turn" to be completed, it
is passed to rbd_img_obj_end_request(), which records the result of
the operation, accumulates transferred bytes, and so on. Next, the
successor to this request is checked and if it is marked "done",
(deferred) completion processing is performed on that request, and
so on. If the last object request in an image request is completed,
rbd_img_request_complete() is called, which (typically) destroys
the image request.
There is a race here, however. The instant an object request is
marked "done" it can be provided (by a thread handling completion of
one of its predecessor operations) to rbd_img_obj_end_request(),
which (for the last request) can then lead to the image request
getting torn down. And this can happen *before* that object has
itself entered rbd_img_obj_end_request(). As a result, once it
*does* enter that function, the image request (and even the object
request itself) may have been freed and become invalid.
All that's necessary to avoid this is to properly count references
to the image requests. We tear down an image request's object
requests all at once--only when the entire image request has
completed. So there's no need for an image request to count
references for its object requests. However, we don't want an
image request to go away until the last of its object requests
has passed through rbd_img_obj_callback(). In other words,
we don't want rbd_img_request_complete() to necessarily
result in the image request being destroyed, because it may
get called before we've finished processing on all of its
object requests.
So the fix is to add a reference to an image request for
each of its object requests. The reference can be viewed
as representing an object request that has not yet finished
its call to rbd_img_obj_callback(). That is emphasized by
getting the reference right after assigning that as the image
object's callback function. The corresponding release of that
reference is done at the end of rbd_img_obj_callback(), which
every image object request passes through exactly once.
Cc: stable@vger.kernel.org
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Ilya Dryomov <ilya.dryomov@inktank.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
osd_request, along with r_request and r_reply messages attached to it
are leaked in __rbd_dev_header_watch_sync() if the requested image
doesn't exist. This is because lingering requests are special and get
an extra ref in the reply path. Fix it by unregistering linger request
on the error path and split __rbd_dev_header_watch_sync() into two
functions to make it maintainable.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Given an existing idle mapping (img1), mapping an image (img2) in
a newly created pool (pool2) fails:
$ ceph osd pool create pool1 8 8
$ rbd create --size 1000 pool1/img1
$ sudo rbd map pool1/img1
$ ceph osd pool create pool2 8 8
$ rbd create --size 1000 pool2/img2
$ sudo rbd map pool2/img2
rbd: sysfs write failed
rbd: map failed: (2) No such file or directory
This is because client instances are shared by default and we don't
request an osdmap update when bumping a ref on an existing client. The
fix is to use the mon_get_version request to see if the osdmap we have
is the latest, and block until the requested update is received if it's
not.
Fixes: http://tracker.ceph.com/issues/8184
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch fixes coccinelle error regarding usage of IS_ERR and
PTR_ERR instead of PTR_ERR_OR_ZERO.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Reviewed-by: Yan, Zheng <zheng.z.yan@intel.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Pull block layer fixes from Jens Axboe:
"Final small batch of fixes to be included before -rc1. Some general
cleanups in here as well, but some of the blk-mq fixes we need for the
NVMe conversion and/or scsi-mq. The pull request contains:
- Support for not merging across a specified "chunk size", if set by
the driver. Some NVMe devices perform poorly for IO that crosses
such a chunk, so we need to support it generically as part of
request merging avoid having to do complicated split logic. From
me.
- Bump max tag depth to 10Ki tags. Some scsi devices have a huge
shared tag space. Before we failed with EINVAL if a too large tag
depth was specified, now we truncate it and pass back the actual
value. From me.
- Various blk-mq rq init fixes from me and others.
- A fix for enter on a dying queue for blk-mq from Keith. This is
needed to prevent oopsing on hot device removal.
- Fixup for blk-mq timer addition from Ming Lei.
- Small round of performance fixes for mtip32xx from Sam Bradshaw.
- Minor stack leak fix from Rickard Strandqvist.
- Two __init annotations from Fabian Frederick"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: add __init to blkcg_policy_register
block: add __init to elv_register
block: ensure that bio_add_page() always accepts a page for an empty bio
blk-mq: add timer in blk_mq_start_request
blk-mq: always initialize request->start_time
block: blk-exec.c: Cleaning up local variable address returnd
mtip32xx: minor performance enhancements
blk-mq: ->timeout should be cleared in blk_mq_rq_ctx_init()
blk-mq: don't allow queue entering for a dying queue
blk-mq: bump max tag depth to 10K tags
block: add blk_rq_set_block_pc()
block: add notion of a chunk size for request merging
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This patch adds the following:
1) Compiler hinting in the fast path.
2) A prefetch of port->flags to eliminate moderate cpu stalling later
in mtip_hw_submit_io().
3) Eliminate a redundant rq_data_dir().
4) Reorder members of driver_data to eliminate false cacheline sharing
between irq_workers_active and unal_qdepth.
With some workload and topology configurations, I'm seeing ~1.5%
throughput improvement in small block random read benchmarks as well
as improved latency std. dev.
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Add include of <linux/prefetch.h>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
With the optimizations around not clearing the full request at alloc
time, we are leaving some of the needed init for REQ_TYPE_BLOCK_PC
up to the user allocating the request.
Add a blk_rq_set_block_pc() that sets the command type to
REQ_TYPE_BLOCK_PC, and properly initializes the members associated
with this type of request. Update callers to use this function instead
of manipulating rq->cmd_type directly.
Includes fixes from Christoph Hellwig <hch@lst.de> for my half-assed
attempt.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |/ / / /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Len field is already set to zero, but not the from field which is sent
as 0xfffffffffffffe00. This makes no sense, and may cause confuse
server implementations doing sanity checks (qemu-nbd is an example.)
Signed-off-by: Hani Benhabiles <hani@linux.com>
Cc: Paul Clements <paul.clements@us.sios.com>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Merge misc updates from Andrew Morton:
- a few fixes for 3.16. Cc'ed to stable so they'll get there somehow.
- various misc fixes and cleanups
- most of the ocfs2 queue. Review is slow...
- most of MM. The MM queue is pretty huge this time, but not much in
the way of feature work.
- some tweaks under kernel/
- printk maintenance work
- updates to lib/
- checkpatch updates
- tweaks to init/
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (276 commits)
fs/autofs4/dev-ioctl.c: add __init to autofs_dev_ioctl_init
fs/ncpfs/getopt.c: replace simple_strtoul by kstrtoul
init/main.c: remove an ifdef
kthreads: kill CLONE_KERNEL, change kernel_thread(kernel_init) to avoid CLONE_SIGHAND
init/main.c: add initcall_blacklist kernel parameter
init/main.c: don't use pr_debug()
fs/binfmt_flat.c: make old_reloc() static
fs/binfmt_elf.c: fix bool assignements
fs/efs: convert printk(KERN_DEBUG to pr_debug
fs/efs: add pr_fmt / use __func__
fs/efs: convert printk to pr_foo()
scripts/checkpatch.pl: device_initcall is not the only __initcall substitute
checkpatch: check stable email address
checkpatch: warn on unnecessary void function return statements
checkpatch: prefer kstrto<foo> to sscanf(buf, "%<lhuidx>", &bar);
checkpatch: add warning for kmalloc/kzalloc with multiply
checkpatch: warn on #defines ending in semicolon
checkpatch: make --strict a default for files in drivers/net and net/
checkpatch: always warn on missing blank line after variable declaration block
checkpatch: fix wildcard DT compatible string checking
...
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
We want to skip the physical block(PAGE_SIZE) which is partially covered
by the discard bio, so we check the remaining size and subtract it if
there is a need to goto the next physical block.
The current offset usage in zram_bio_discard is incorrect, it will cause
its upper filesystem breakdown. Consider the following scenario:
On some architecture or config, PAGE_SIZE is 64K for example, filesystem
is set up on zram disk without PAGE_SIZE aligned, a discard bio leads to a
offset = 4K and size=72K, normally, it should not really discard any
physical block as it partially cover two physical blocks. However, with
the current offset usage, it will discard the second physical block and
free its memory, which will cause filesystem breakdown.
This patch corrects the offset usage in zram_bio_discard.
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
brd is effectively a thinly provisioned device. Thinly provisioned
devices return -ENOSPC when they can't write a new block. -ENOMEM is an
implementation detail that callers shouldn't know.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Acked-by: Dave Chinner <david@fromorbit.com>
Cc: Dheeraj Reddy <dheeraj.reddy@intel.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dheeraj Reddy <dheeraj.reddy@intel.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |/ / / /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We currently pass in the hardware queue, and get the tags from there.
But from scsi-mq, with a shared tag space, it's a lot more convenient
to pass in the blk_mq_tags instead as the hardware queue isn't always
directly available. So instead of having to re-map to a given
hardware queue from rq->mq_ctx, just pass in the tags structure.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into next
Pull scheduler updates from Ingo Molnar:
"The main scheduling related changes in this cycle were:
- various sched/numa updates, for better performance
- tree wide cleanup of open coded nice levels
- nohz fix related to rq->nr_running use
- cpuidle changes and continued consolidation to improve the
kernel/sched/idle.c high level idle scheduling logic. As part of
this effort I pulled cpuidle driver changes from Rafael as well.
- standardized idle polling amongst architectures
- continued work on preparing better power/energy aware scheduling
- sched/rt updates
- misc fixlets and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (49 commits)
sched/numa: Decay ->wakee_flips instead of zeroing
sched/numa: Update migrate_improves/degrades_locality()
sched/numa: Allow task switch if load imbalance improves
sched/rt: Fix 'struct sched_dl_entity' and dl_task_time() comments, to match the current upstream code
sched: Consolidate open coded implementations of nice level frobbing into nice_to_rlimit() and rlimit_to_nice()
sched: Initialize rq->age_stamp on processor start
sched, nohz: Change rq->nr_running to always use wrappers
sched: Fix the rq->next_balance logic in rebalance_domains() and idle_balance()
sched: Use clamp() and clamp_val() to make sys_nice() more readable
sched: Do not zero sg->cpumask and sg->sgp->power in build_sched_groups()
sched/numa: Fix initialization of sched_domain_topology for NUMA
sched: Call select_idle_sibling() when not affine_sd
sched: Simplify return logic in sched_read_attr()
sched: Simplify return logic in sched_copy_attr()
sched: Fix exec_start/task_hot on migrated tasks
arm64: Remove TIF_POLLING_NRFLAG
metag: Remove TIF_POLLING_NRFLAG
sched/idle: Make cpuidle_idle_call() void
sched/idle: Reflow cpuidle_idle_call()
sched/idle: Delay clearing the polling bit
...
|
| | |\| | |
| | | | |
| | | | |
| | | | | |
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | |\ \ \ \
| | | |/ /
| | |/| |
| | | | | |
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Replace various -20/+19 hardcoded nice values with MIN_NICE/MAX_NICE.
Signed-off-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/ff13819fd09b7a5dba5ab5ae797f2e7019bdfa17.1394532288.git.yangds.fnst@cn.fujitsu.com
Cc: devel@driverdev.osuosl.org
Cc: devicetree@vger.kernel.org
Cc: fcoe-devel@open-fcoe.org
Cc: linux390@de.ibm.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-mm@kvack.org
Cc: linux-s390@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: nbd-general@lists.sourceforge.net
Cc: ocfs2-devel@oss.oracle.com
Cc: openipmi-developer@lists.sourceforge.net
Cc: qla2xxx-upstream@qlogic.com
Cc: linux-arch@vger.kernel.org
[ Consolidated the patches, twiddled the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
