summaryrefslogtreecommitdiffstats
path: root/configs/platform-v7a/barebox-rpi2.config
Commit message (Collapse)AuthorAgeFilesLines
* platform-v7a: Add barebox patchstackSascha Hauer2020-01-081-1/+1
| | | | | | | | This adds a barebox patchstack which is needed for the rasperrypi which otherwise issues several warnings during boot. While at it add DWC2 USB support as well to finally get networking support for the raspberrypi. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* barebox-rpi2: Update configSascha Hauer2020-01-081-54/+15
| | | | | | | | | | | | | | | Enable more features and clean up: - Enable DWC2 USB controller support - Enable Networking - Compile in thumb2 mode - Disable unused USB gadget support - Set malloc area size to 0x0 to let barebox autoconfigure memory size - Disable unused I2C support - Disable unused EHCI driver - Enable raspberrypi EXP GPIO driver Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* platform-v7a: barebox: version bump 2019.11.0 -> 2019.12.0DistroKit-2019.12.0Sascha Hauer2019-12-201-1/+3
| | | | | | Use the latest and greatest. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* platform-v7a: barebox: version bump 2019.10.0 -> 2019.11.0Robert Schwebel2019-11-111-2/+15
| | | | | | A new barebox version is out, use it. Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
* barebox: create the .ptxdist-defaultenv symlink in the build dirMichael Olbrich2019-11-041-1/+1
| | | | | | | This avoids problems if the same git tree is used in local_src/ for multiple barebox packages. Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
* v7a: barebox: version bump 2019.08.1 → 2019.10.0Ahmad Fatoum2019-11-041-1/+10
| | | | | | | There's a new barebox in town. Upgrade to it. Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
* v7a: barebox: version bump 2019.07.0 → 2019.08.1Roland Hieber2019-08-211-2/+65
| | | | Signed-off-by: Roland Hieber <rhi@pengutronix.de>
* v7a: barebox: version bump 2019.06.1 -> 2019.07.0Ahmad Fatoum2019-08-211-2/+4
| | | | | | | | | Particularly relevant in this release is the v5.2 device tree sync which is a prerequisite for the incoming STM32MP1 support. Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Roland Hieber <rhi@pengutronix.de> Tested-by: Roland Hieber <rhi@pengutronix.de>
* v7a: barebox-rpi2: enable BCM283X_SDHOSTRoland Hieber2019-07-091-1/+1
| | | | | | | | | | | | Since barebox v2019.06.0 [1], there is now an driver for the sdhost on the RPi 3, and the sdhost/sdhci pin-swapping workaround in the RPi 3 device tree was undone again [2]. Therefore we now need to build the sdhost driver so the RPi 3 barebox can read SD cards again. [1]: barebox commit d6d3d0aecece84afe9eb ("mci: add driver for BCM283x sdhost core") [2]: barebox commit 9036d1db4d4a9a61bcda ("ARM: rpi3: remove swapped sdhci and sdhost") Signed-off-by: Roland Hieber <rhi@pengutronix.de>
* v7a: barebox: version bump 2019.03.0 -> 2019.06.1Roland Hieber2019-07-091-4/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | Just a simple oldconfig with default values for all variants with the help of ./scripts/update-diffs-v7a.sh. Changes in config symbols: * BAREBOX_MAX_PBLX_SIZE was removed in v2019.04.0 because pblx was removed. The maximum file size is now instead determined by BAREBOX_MAX_IMAGE_SIZE. [1] * The m25p80 driver was refactored to use the spi_mem API [2] (affects am355x and mx6) * The ARMv8 clocksource can now also work with ARMv7 timers, so it is auto-enabled by kconfig since barebox v2019.05.0. [3] * GPIO_BCM283X was replaced by PINCTRL_BCM283X in v2019.04.0. [4] * CRC16 was replaced by CRC_ITU_T in v2019.04.0 [5], but since it has no prompt in the menu and it is actually not selected by anyone except on am335x-mlo, it now stays disabled in the other variants. Relevant barebox commits: [1]: 9e72ea7a006cd0931913 ("images: pbl: verify CONFIG_BAREBOX_MAX_IMAGE_SIZE is not exceeded" [2]: 80b6b874944d7982e6c7 ("mtd: devices: m25p80: use the spi_mem_xx() API") [3]: dece707522434d5c8eb3 ("clocksource: Enable architected timer support for CPU_V7") [4]: be717102c8ba2d0ea022 ("pinctrl: bcm2835: move existing code from gpio.") [5]: 74de1afbd2ed4262d410 ("crc: import crc_itu_t() from kernel") Signed-off-by: Roland Hieber <rhi@pengutronix.de>
* v7a: barebox-rpi2: slim down config diffRoland Hieber2019-06-051-41/+165
| | | | | | | | | | | | | | | | | | | | | * don't disable common features unnecessarily: enable the features BOOTM_*, BZLIB, DRIVER_SPI_GPIO, HWRNG, I2C, I2C_GPIO, IMD, LED_GPIO_OF, LZO_DECOMPRESS, MCI_MMCI, MTD, NET, NET_NFS, NET_RESOLV, NET_IFUP, NET_DHCP, NET_USB_*, OF_BAREBOX_DRIVERS, OF_NET, PINCTRL, RESET_SOURCE, STATE, USB_EHCI, USB_GADGET_SERIAL, USB_HOST, USB_STORAGE, XZ_DECOMPRESS, ZLIB, and the commands cmd, dhcp, host, i2c, imd, ip-route-get, led, trigger, memtest, ping, regulator, sha1sum, spi, state, tftp, and usb. All of those are enabled in the barebox-common config too, and make sense to have on a generic barebox. * repair compile log level < default log level by using the defaults * disable unneeded features: - CMD_LOADB: no one uses kermit these days - BAREBOXENV_TARGET: should come from a common barebox-tools package - CMD_MENU_MANAGEMENT: not used - PASSWORD: not used Signed-off-by: Roland Hieber <rhi@pengutronix.de>
* platform-v7a: barebox bump v2019.01.0 → v2019.03.0Rouven Czerwinski2019-03-071-8/+7
| | | | | | Patch free, baby! Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
* platform-v7a: barebox 2018.12.0 → 2019.01.0Rouven Czerwinski2019-01-181-1/+6
| | | | Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
* platform-v7a: barebox-rpi2: configure commandsRouven Czerwinski2018-12-171-24/+34
| | | | | | Configure barebox for rpi2 and rpi3 for the test suite commands. Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
* add RPI3 SupportRouven Czerwinski2018-12-171-3/+5
| | | | Signed-off-by: Rouven Czerwinski <rouven@czerwinskis.de>
* platform-v7a: barebox bump v2018.05.0 → v2018.12.0Rouven Czerwinski2018-12-071-1/+24
| | | | | | | | Bump barebox from v2018.05.0 to v2018.12.0. This barebox release officially supports RPI3, this will be enabled in a later commit. Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
* platform-v7a: barebox-rpi2: add layer supportMichael Olbrich2018-10-261-1/+1
| | | | | | Remove all references to PTXDIST_PLATFORMCONFIGDIR to do this. Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
* platform-v7a: barebox: version bump 2018.03.0 -> 2018.05.0Roland Hieber2018-05-161-3/+5
| | | | | | | Bump all barebox variants, followed by oldconfig. Consistently enable CONSOLE_ALLOW_COLOR, otherwise use default values. Signed-off-by: Roland Hieber <r.hieber@pengutronix.de>
* barebox: version bump 2018.01.0 -> 2018.03.0Robert Schwebel2018-03-071-1/+6
| | | | | | Update the barebox version to the latest and greatest. Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
* platform-v7a: barebox: version bump 2017.11.0 -> 2018.01.0Roland Hieber2018-01-291-1/+1
| | | | | | | | | | | Migrate the patches and make oldconfig without adding any new features. Note that barebox-rpi2 is still broken, but we'll bump it anyway for completeness. Tested-by: Robert Schwebel <r.schwebel@pengutronix.de> (for qemu-vexpress) Tested-by: Roland Hieber <r.hieber@pengutronix.de> (for qemu-vexpress) Signed-off-by: Roland Hieber <r.hieber@pengutronix.de>
* platform-v7a: barebox-rpi2: RPi 1 support is no longer relevant hereRoland Hieber2018-01-291-3/+2
| | | | | | | The Raspberry Pi 1 is not based on ARMv7-A, but on ARMv6, and is supported by platform-rpi. Signed-off-by: Roland Hieber <r.hieber@pengutronix.de>
* barebox: version bump 2017.08.0 -> 2017.10.0Robert Schwebel2017-10-111-1/+2
| | | | | Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de> Reviewed-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
* platform-v7a: barebox: version bump v2017.07.0 -> v2017.08.0Robert Schwebel2017-08-221-1/+1
| | | | | | Barebox upstream has version bumped, and so do we. Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
* platform-v7a: rpi2: create own rpi2 barebox defaultenvChris Fiege2017-07-041-1/+1
| | | | | | | Using this change the barebox-rpi2 package has its own defaultenv directory. Signed-off-by: Chris Fiege <c.fiege@pengutronix.de>
* platform-v7a: barebox: version bump 2017.06.0 -> 2017.07.0Robert Schwebel2017-07-041-0/+570
Update barebox 2017.07.0, which contains an important fix for nv and globalvars. In the previous patch stack, state was defect, as upstream has changed the oftree. This is fixed in the new patch series. Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-05-01 16:03:49 +0000