Major PCMCIA Cleanup to make code better readable and maintainable.

Notes:
- Board-dependend code for RPXLITE and RPXCLASSIC-based boards
  placed to the drivers/rpx_pmcia.c file to avoid duplication.
  Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
- drivers/i82365.c has been split into two parts located at
  board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
  the only boards using CONFIG_82365).
- Changes were tested for clean build and *very* *few* boards.

24 files changed, 3589 insertions, 38 deletions

diff --git a/board/atc/Makefile b/board/atc/Makefile
index 7a2014d466..7573a0c771 100644
--- a/board/atc/Makefile
+++ b/board/atc/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o
+OBJS	= $(BOARD).o flash.o ti113x.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/atc/ti113x.c b/board/atc/ti113x.c
new file mode 100644
index 0000000000..d5e935c400
--- /dev/null
+++ b/board/atc/ti113x.c
@@ -0,0 +1,637 @@
+/*
+ * (C) Copyright 2003-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ ********************************************************************
+ *
+ * Lots of code copied from:
+ *
+ * i82365.c 1.352 - Linux driver for Intel 82365 and compatible
+ * PC Card controllers, and Yenta-compatible PCI-to-CardBus controllers.
+ * (C) 1999 David A. Hinds <dahinds@users.sourceforge.net>
+ */
+
+#include <common.h>
+
+#ifdef CONFIG_I82365
+
+#include <command.h>
+#include <pci.h>
+#include <pcmcia.h>
+#include <asm/io.h>
+
+#include <pcmcia/ss.h>
+#include <pcmcia/i82365.h>
+#include <pcmcia/yenta.h>
+#include <pcmcia/ti113x.h>
+
+static struct pci_device_id supported[] = {
+	{PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_1510},
+	{0, 0}
+};
+
+#define CYCLE_TIME	120
+
+#ifdef DEBUG
+static void i82365_dump_regions (pci_dev_t dev);
+#endif
+
+typedef struct socket_info_t {
+	pci_dev_t	dev;
+	u_short		bcr;
+	u_char		pci_lat, cb_lat, sub_bus, cache;
+	u_int		cb_phys;
+
+	socket_cap_t	cap;
+	u_short		type;
+	u_int		flags;
+	ti113x_state_t	state;
+} socket_info_t;
+
+static socket_info_t socket;
+static socket_state_t state;
+static struct pccard_mem_map mem;
+static struct pccard_io_map io;
+
+/*====================================================================*/
+
+/* Some PCI shortcuts */
+
+static int pci_readb (socket_info_t * s, int r, u_char * v)
+{
+	return pci_read_config_byte (s->dev, r, v);
+}
+static int pci_writeb (socket_info_t * s, int r, u_char v)
+{
+	return pci_write_config_byte (s->dev, r, v);
+}
+static int pci_readw (socket_info_t * s, int r, u_short * v)
+{
+	return pci_read_config_word (s->dev, r, v);
+}
+static int pci_writew (socket_info_t * s, int r, u_short v)
+{
+	return pci_write_config_word (s->dev, r, v);
+}
+static int pci_readl (socket_info_t * s, int r, u_int * v)
+{
+	return pci_read_config_dword (s->dev, r, v);
+}
+static int pci_writel (socket_info_t * s, int r, u_int v)
+{
+	return pci_write_config_dword (s->dev, r, v);
+}
+
+/*====================================================================*/
+
+#define cb_readb(s, r)		readb((s)->cb_phys + (r))
+#define cb_readl(s, r)		readl((s)->cb_phys + (r))
+#define cb_writeb(s, r, v)	writeb(v, (s)->cb_phys + (r))
+#define cb_writel(s, r, v)	writel(v, (s)->cb_phys + (r))
+
+static u_char i365_get (socket_info_t * s, u_short reg)
+{
+	return cb_readb (s, 0x0800 + reg);
+}
+
+static void i365_set (socket_info_t * s, u_short reg, u_char data)
+{
+	cb_writeb (s, 0x0800 + reg, data);
+}
+
+static void i365_bset (socket_info_t * s, u_short reg, u_char mask)
+{
+	i365_set (s, reg, i365_get (s, reg) | mask);
+}
+
+static void i365_bclr (socket_info_t * s, u_short reg, u_char mask)
+{
+	i365_set (s, reg, i365_get (s, reg) & ~mask);
+}
+
+#if 0	/* not used */
+static void i365_bflip (socket_info_t * s, u_short reg, u_char mask, int b)
+{
+	u_char d = i365_get (s, reg);
+
+	i365_set (s, reg, (b) ? (d | mask) : (d & ~mask));
+}
+
+static u_short i365_get_pair (socket_info_t * s, u_short reg)
+{
+	return (i365_get (s, reg) + (i365_get (s, reg + 1) << 8));
+}
+#endif	/* not used */
+
+static void i365_set_pair (socket_info_t * s, u_short reg, u_short data)
+{
+	i365_set (s, reg, data & 0xff);
+	i365_set (s, reg + 1, data >> 8);
+}
+
+/*======================================================================
+
+    Code to save and restore global state information for TI 1130 and
+    TI 1131 controllers, and to set and report global configuration
+    options.
+
+======================================================================*/
+
+static void ti113x_get_state (socket_info_t * s)
+{
+	ti113x_state_t *p = &s->state;
+
+	pci_readl (s, TI113X_SYSTEM_CONTROL, &p->sysctl);
+	pci_readb (s, TI113X_CARD_CONTROL, &p->cardctl);
+	pci_readb (s, TI113X_DEVICE_CONTROL, &p->devctl);
+	pci_readb (s, TI1250_DIAGNOSTIC, &p->diag);
+	pci_readl (s, TI12XX_IRQMUX, &p->irqmux);
+}
+
+static void ti113x_set_state (socket_info_t * s)
+{
+	ti113x_state_t *p = &s->state;
+
+	pci_writel (s, TI113X_SYSTEM_CONTROL, p->sysctl);
+	pci_writeb (s, TI113X_CARD_CONTROL, p->cardctl);
+	pci_writeb (s, TI113X_DEVICE_CONTROL, p->devctl);
+	pci_writeb (s, TI1250_MULTIMEDIA_CTL, 0);
+	pci_writeb (s, TI1250_DIAGNOSTIC, p->diag);
+	pci_writel (s, TI12XX_IRQMUX, p->irqmux);
+	i365_set_pair (s, TI113X_IO_OFFSET (0), 0);
+	i365_set_pair (s, TI113X_IO_OFFSET (1), 0);
+}
+
+static u_int ti113x_set_opts (socket_info_t * s)
+{
+	ti113x_state_t *p = &s->state;
+	u_int mask = 0xffff;
+
+	p->cardctl &= ~TI113X_CCR_ZVENABLE;
+	p->cardctl |= TI113X_CCR_SPKROUTEN;
+
+	return mask;
+}
+
+/*======================================================================
+
+    Routines to handle common CardBus options
+
+======================================================================*/
+
+/* Default settings for PCI command configuration register */
+#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
+		  PCI_COMMAND_MASTER|PCI_COMMAND_WAIT)
+
+static void cb_get_state (socket_info_t * s)
+{
+	pci_readb (s, PCI_CACHE_LINE_SIZE, &s->cache);
+	pci_readb (s, PCI_LATENCY_TIMER, &s->pci_lat);
+	pci_readb (s, CB_LATENCY_TIMER, &s->cb_lat);
+	pci_readb (s, CB_CARDBUS_BUS, &s->cap.cardbus);
+	pci_readb (s, CB_SUBORD_BUS, &s->sub_bus);
+	pci_readw (s, CB_BRIDGE_CONTROL, &s->bcr);
+}
+
+static void cb_set_state (socket_info_t * s)
+{
+	pci_writel (s, CB_LEGACY_MODE_BASE, 0);
+	pci_writel (s, PCI_BASE_ADDRESS_0, s->cb_phys);
+	pci_writew (s, PCI_COMMAND, CMD_DFLT);
+	pci_writeb (s, PCI_CACHE_LINE_SIZE, s->cache);
+	pci_writeb (s, PCI_LATENCY_TIMER, s->pci_lat);
+	pci_writeb (s, CB_LATENCY_TIMER, s->cb_lat);
+	pci_writeb (s, CB_CARDBUS_BUS, s->cap.cardbus);
+	pci_writeb (s, CB_SUBORD_BUS, s->sub_bus);
+	pci_writew (s, CB_BRIDGE_CONTROL, s->bcr);
+}
+
+static void cb_set_opts (socket_info_t * s)
+{
+	if (s->cache == 0)
+		s->cache = 8;
+	if (s->pci_lat == 0)
+		s->pci_lat = 0xa8;
+	if (s->cb_lat == 0)
+		s->cb_lat = 0xb0;
+}
+
+/*======================================================================
+
+    Power control for Cardbus controllers: used both for 16-bit and
+    Cardbus cards.
+
+======================================================================*/
+
+static int cb_set_power (socket_info_t * s, socket_state_t * state)
+{
+	u_int reg = 0;
+
+	/* restart card voltage detection if it seems appropriate */
+	if ((state->Vcc == 0) && (state->Vpp == 0) &&
+	   !(cb_readl (s, CB_SOCKET_STATE) & CB_SS_VSENSE))
+		cb_writel (s, CB_SOCKET_FORCE, CB_SF_CVSTEST);
+	switch (state->Vcc) {
+	case 0:
+		reg = 0;
+		break;
+	case 33:
+		reg = CB_SC_VCC_3V;
+		break;
+	case 50:
+		reg = CB_SC_VCC_5V;
+		break;
+	default:
+		return -1;
+	}
+	switch (state->Vpp) {
+	case 0:
+		break;
+	case 33:
+		reg |= CB_SC_VPP_3V;
+		break;
+	case 50:
+		reg |= CB_SC_VPP_5V;
+		break;
+	case 120:
+		reg |= CB_SC_VPP_12V;
+		break;
+	default:
+		return -1;
+	}
+	if (reg != cb_readl (s, CB_SOCKET_CONTROL))
+		cb_writel (s, CB_SOCKET_CONTROL, reg);
+
+	return 0;
+}
+
+/*======================================================================
+
+    Generic routines to get and set controller options
+
+======================================================================*/
+
+static void get_bridge_state (socket_info_t * s)
+{
+	ti113x_get_state (s);
+	cb_get_state (s);
+}
+
+static void set_bridge_state (socket_info_t * s)
+{
+	cb_set_state (s);
+	i365_set (s, I365_GBLCTL, 0x00);
+	i365_set (s, I365_GENCTL, 0x00);
+	ti113x_set_state (s);
+}
+
+static void set_bridge_opts (socket_info_t * s)
+{
+	ti113x_set_opts (s);
+	cb_set_opts (s);
+}
+
+/*====================================================================*/
+#define PD67_EXT_INDEX		0x2e	/* Extension index */
+#define PD67_EXT_DATA		0x2f	/* Extension data */
+#define PD67_EXD_VS1(s)		(0x01 << ((s)<<1))
+
+#define pd67_ext_get(s, r) \
+    (i365_set(s, PD67_EXT_INDEX, r), i365_get(s, PD67_EXT_DATA))
+
+static int i365_get_status (socket_info_t * s, u_int * value)
+{
+	u_int status;
+
+	status = i365_get (s, I365_IDENT);
+	status = i365_get (s, I365_STATUS);
+	*value = ((status & I365_CS_DETECT) == I365_CS_DETECT) ? SS_DETECT : 0;
+	if (i365_get (s, I365_INTCTL) & I365_PC_IOCARD) {
+		*value |= (status & I365_CS_STSCHG) ? 0 : SS_STSCHG;
+	} else {
+		*value |= (status & I365_CS_BVD1) ? 0 : SS_BATDEAD;
+		*value |= (status & I365_CS_BVD2) ? 0 : SS_BATWARN;
+	}
+	*value |= (status & I365_CS_WRPROT) ? SS_WRPROT : 0;
+	*value |= (status & I365_CS_READY) ? SS_READY : 0;
+	*value |= (status & I365_CS_POWERON) ? SS_POWERON : 0;
+
+	status = cb_readl (s, CB_SOCKET_STATE);
+	*value |= (status & CB_SS_32BIT) ? SS_CARDBUS : 0;
+	*value |= (status & CB_SS_3VCARD) ? SS_3VCARD : 0;
+	*value |= (status & CB_SS_XVCARD) ? SS_XVCARD : 0;
+	*value |= (status & CB_SS_VSENSE) ? 0 : SS_PENDING;
+	/* For now, ignore cards with unsupported voltage keys */
+	if (*value & SS_XVCARD)
+		*value &= ~(SS_DETECT | SS_3VCARD | SS_XVCARD);
+
+	return 0;
+}	/* i365_get_status */
+
+static int i365_set_socket (socket_info_t * s, socket_state_t * state)
+{
+	u_char reg;
+
+	set_bridge_state (s);
+
+	/* IO card, RESET flag */
+	reg = 0;
+	reg |= (state->flags & SS_RESET) ? 0 : I365_PC_RESET;
+	reg |= (state->flags & SS_IOCARD) ? I365_PC_IOCARD : 0;
+	i365_set (s, I365_INTCTL, reg);
+
+	reg = I365_PWR_NORESET;
+	if (state->flags & SS_PWR_AUTO)
+		reg |= I365_PWR_AUTO;
+	if (state->flags & SS_OUTPUT_ENA)
+		reg |= I365_PWR_OUT;
+
+	cb_set_power (s, state);
+	reg |= i365_get (s, I365_POWER) & (I365_VCC_MASK | I365_VPP1_MASK);
+
+	if (reg != i365_get (s, I365_POWER))
+		i365_set (s, I365_POWER, reg);
+
+	return 0;
+}	/* i365_set_socket */
+
+/*====================================================================*/
+
+static int i365_set_mem_map (socket_info_t * s, struct pccard_mem_map *mem)
+{
+	u_short base, i;
+	u_char map;
+
+	debug ("i82365: SetMemMap(%d, %#2.2x, %d ns, %#5.5lx-%#5.5lx, %#5.5x)\n",
+		mem->map, mem->flags, mem->speed,
+		mem->sys_start, mem->sys_stop, mem->card_start);
+
+	map = mem->map;
+	if ((map > 4) ||
+	    (mem->card_start > 0x3ffffff) ||
+	    (mem->sys_start > mem->sys_stop) ||
+	    (mem->speed > 1000)) {
+		return -1;
+	}
+
+	/* Turn off the window before changing anything */
+	if (i365_get (s, I365_ADDRWIN) & I365_ENA_MEM (map))
+		i365_bclr (s, I365_ADDRWIN, I365_ENA_MEM (map));
+
+	/* Take care of high byte, for PCI controllers */
+	i365_set (s, CB_MEM_PAGE (map), mem->sys_start >> 24);
+
+	base = I365_MEM (map);
+	i = (mem->sys_start >> 12) & 0x0fff;
+	if (mem->flags & MAP_16BIT)
+		i |= I365_MEM_16BIT;
+	if (mem->flags & MAP_0WS)
+		i |= I365_MEM_0WS;
+	i365_set_pair (s, base + I365_W_START, i);
+
+	i = (mem->sys_stop >> 12) & 0x0fff;
+	switch (mem->speed / CYCLE_TIME) {
+	case 0:
+		break;
+	case 1:
+		i |= I365_MEM_WS0;
+		break;
+	case 2:
+		i |= I365_MEM_WS1;
+		break;
+	default:
+		i |= I365_MEM_WS1 | I365_MEM_WS0;
+		break;
+	}
+	i365_set_pair (s, base + I365_W_STOP, i);
+
+	i = ((mem->card_start - mem->sys_start) >> 12) & 0x3fff;
+	if (mem->flags & MAP_WRPROT)
+		i |= I365_MEM_WRPROT;
+	if (mem->flags & MAP_ATTRIB)
+		i |= I365_MEM_REG;
+	i365_set_pair (s, base + I365_W_OFF, i);
+
+	/* Turn on the window if necessary */
+	if (mem->flags & MAP_ACTIVE)
+		i365_bset (s, I365_ADDRWIN, I365_ENA_MEM (map));
+	return 0;
+}	/* i365_set_mem_map */
+
+static int i365_set_io_map (socket_info_t * s, struct pccard_io_map *io)
+{
+	u_char map, ioctl;
+
+	map = io->map;
+	/* comment out: comparison is always false due to limited range of data type */
+	if ((map > 1) || /* (io->start > 0xffff) || (io->stop > 0xffff) || */
+	    (io->stop < io->start))
+		return -1;
+	/* Turn off the window before changing anything */
+	if (i365_get (s, I365_ADDRWIN) & I365_ENA_IO (map))
+		i365_bclr (s, I365_ADDRWIN, I365_ENA_IO (map));
+	i365_set_pair (s, I365_IO (map) + I365_W_START, io->start);
+	i365_set_pair (s, I365_IO (map) + I365_W_STOP, io->stop);
+	ioctl = i365_get (s, I365_IOCTL) & ~I365_IOCTL_MASK (map);
+	if (io->speed)
+		ioctl |= I365_IOCTL_WAIT (map);
+	if (io->flags & MAP_0WS)
+		ioctl |= I365_IOCTL_0WS (map);
+	if (io->flags & MAP_16BIT)
+		ioctl |= I365_IOCTL_16BIT (map);
+	if (io->flags & MAP_AUTOSZ)
+		ioctl |= I365_IOCTL_IOCS16 (map);
+	i365_set (s, I365_IOCTL, ioctl);
+	/* Turn on the window if necessary */
+	if (io->flags & MAP_ACTIVE)
+		i365_bset (s, I365_ADDRWIN, I365_ENA_IO (map));
+	return 0;
+}	/* i365_set_io_map */
+
+/*====================================================================*/
+
+int i82365_init (void)
+{
+	u_int val;
+	int i;
+
+	if ((socket.dev = pci_find_devices (supported, 0)) < 0) {
+		/* Controller not found */
+		return 1;
+	}
+	debug ("i82365 Device Found!\n");
+
+	pci_read_config_dword (socket.dev, PCI_BASE_ADDRESS_0, &socket.cb_phys);
+	socket.cb_phys &= ~0xf;
+
+	get_bridge_state (&socket);
+	set_bridge_opts (&socket);
+
+	i = i365_get_status (&socket, &val);
+
+	if (val & SS_DETECT) {
+		if (val & SS_3VCARD) {
+			state.Vcc = state.Vpp = 33;
+			puts (" 3.3V card found: ");
+		} else if (!(val & SS_XVCARD)) {
+			state.Vcc = state.Vpp = 50;
+			puts (" 5.0V card found: ");
+		} else {
+			puts ("i82365: unsupported voltage key\n");
+			state.Vcc = state.Vpp = 0;
+		}
+	} else {
+		/* No card inserted */
+		puts ("No card\n");
+		return 1;
+	}
+
+	state.flags = SS_IOCARD | SS_OUTPUT_ENA;
+	state.csc_mask = 0;
+	state.io_irq = 0;
+
+	i365_set_socket (&socket, &state);
+
+	for (i = 500; i; i--) {
+		if ((i365_get (&socket, I365_STATUS) & I365_CS_READY))
+			break;
+		udelay (1000);
+	}
+
+	if (i == 0) {
+		/* PC Card not ready for data transfer */
+		puts ("i82365 PC Card not ready for data transfer\n");
+		return 1;
+	}
+	debug (" PC Card ready for data transfer: ");
+
+	mem.map = 0;
+	mem.flags = MAP_ATTRIB | MAP_ACTIVE;
+	mem.speed = 300;
+	mem.sys_start = CFG_PCMCIA_MEM_ADDR;
+	mem.sys_stop = CFG_PCMCIA_MEM_ADDR + CFG_PCMCIA_MEM_SIZE - 1;
+	mem.card_start = 0;
+	i365_set_mem_map (&socket, &mem);
+
+	io.map = 0;
+	io.flags = MAP_AUTOSZ | MAP_ACTIVE;
+	io.speed = 0;
+	io.start = 0x0100;
+	io.stop = 0x010F;
+	i365_set_io_map (&socket, &io);
+
+#ifdef DEBUG
+	i82365_dump_regions (socket.dev);
+#endif
+
+	return 0;
+}
+
+void i82365_exit (void)
+{
+	io.map = 0;
+	io.flags = 0;
+	io.speed = 0;
+	io.start = 0;
+	io.stop = 0x1;
+
+	i365_set_io_map (&socket, &io);
+
+	mem.map = 0;
+	mem.flags = 0;
+	mem.speed = 0;
+	mem.sys_start = 0;
+	mem.sys_stop = 0x1000;
+	mem.card_start = 0;
+
+	i365_set_mem_map (&socket, &mem);
+
+	socket.state.sysctl &= 0xFFFF00FF;
+
+	state.Vcc = state.Vpp = 0;
+
+	i365_set_socket (&socket, &state);
+}
+
+int pcmcia_on (void)
+{
+	u_int rc;
+
+	debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+	rc = i82365_init();
+	if (rc)
+		goto exit;
+
+	rc = check_ide_device(0);
+	if (rc == 0)
+		goto exit;
+
+	i82365_exit();
+
+exit:
+	return rc;
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_off (void)
+{
+	printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+	i82365_exit();
+
+	return 0;
+}
+#endif
+
+/*======================================================================
+
+    Debug stuff
+
+======================================================================*/
+
+#ifdef DEBUG
+static void i82365_dump_regions (pci_dev_t dev)
+{
+	u_int tmp[2];
+	u_int *mem = (void *) socket.cb_phys;
+	u_char *cis = (void *) CFG_PCMCIA_MEM_ADDR;
+	u_char *ide = (void *) (CFG_ATA_BASE_ADDR + CFG_ATA_REG_OFFSET);
+
+	pci_read_config_dword (dev, 0x00, tmp + 0);
+	pci_read_config_dword (dev, 0x80, tmp + 1);
+
+	printf ("PCI CONF: %08X ... %08X\n",
+		tmp[0], tmp[1]);
+	printf ("PCI MEM:  ... %08X ... %08X\n",
+		mem[0x8 / 4], mem[0x800 / 4]);
+	printf ("CIS:      ...%c%c%c%c%c%c%c%c...\n",
+		cis[0x38], cis[0x3a], cis[0x3c], cis[0x3e],
+		cis[0x40], cis[0x42], cis[0x44], cis[0x48]);
+	printf ("CIS CONF: %02X %02X %02X ...\n",
+		cis[0x200], cis[0x202], cis[0x204]);
+	printf ("IDE:      %02X %02X %02X %02X %02X %02X %02X %02X\n",
+		ide[0], ide[1], ide[2], ide[3],
+		ide[4], ide[5], ide[6], ide[7]);
+}
+#endif	/* DEBUG */
+
+#endif /* CONFIG_I82365 */
diff --git a/board/c2mon/Makefile b/board/c2mon/Makefile
index 7a2014d466..7b2b545820 100644
--- a/board/c2mon/Makefile
+++ b/board/c2mon/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o
+OBJS	= $(BOARD).o flash.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/c2mon/pcmcia.c b/board/c2mon/pcmcia.c
new file mode 100644
index 0000000000..5e50c4d9bc
--- /dev/null
+++ b/board/c2mon/pcmcia.c
@@ -0,0 +1,284 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "C2MON"
+
+static void cfg_ports (void)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	ushort sreg;
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	* Configure Port C for TPS2211 PC-Card Power-Interface Switch
+	*
+	* Switch off all voltages, assert shutdown
+	*/
+	sreg = immap->im_ioport.iop_pcdat;
+	sreg |=  (TPS2211_VPPD0 | TPS2211_VPPD1);	/* VAVPP => Hi-Z */
+	sreg &= ~(TPS2211_VCCD0 | TPS2211_VCCD1);	/* 3V and 5V off */
+	immap->im_ioport.iop_pcdat = sreg;
+
+	immap->im_ioport.iop_pcpar &= ~(TPS2211_OUTPUTS);
+	immap->im_ioport.iop_pcdir |=   TPS2211_OUTPUTS;
+
+	debug ("Set Port C: PAR:     %04x DIR:     %04x DAT:     %04x\n",
+	       immap->im_ioport.iop_pcpar,
+	       immap->im_ioport.iop_pcdir,
+	       immap->im_ioport.iop_pcdat);
+
+	/*
+	* Configure Port B for TPS2211 PC-Card Power-Interface Switch
+	*
+	* Over-Current Input only
+	*/
+	cp->cp_pbpar &= ~(TPS2211_INPUTS);
+	cp->cp_pbdir &= ~(TPS2211_INPUTS);
+
+	debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
+	       cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, pipr, mask;
+	ushort sreg;
+	int i;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
+	cfg_ports ();
+
+	/*
+	* Configure SIUMCR to enable PCMCIA port B
+	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	*/
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
+	*/
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	pipr = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       pipr,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+
+	sreg = immap->im_ioport.iop_pcdat;
+	if ((pipr & mask) == mask) {
+		sreg |=  (TPS2211_VPPD0 | TPS2211_VPPD1 |	/* VAVPP => Hi-Z */
+				TPS2211_VCCD1);			/* 5V on	*/
+		sreg &= ~(TPS2211_VCCD0);			/* 3V off	*/
+		puts (" 5.0V card found: ");
+	} else {
+		sreg |=  (TPS2211_VPPD0 | TPS2211_VPPD1 |	/* VAVPP => Hi-Z */
+				TPS2211_VCCD0);			/* 3V on	*/
+		sreg &= ~(TPS2211_VCCD1);			/* 5V off	*/
+		puts (" 3.3V card found: ");
+	}
+
+	debug ("\nPC DAT: %04x -> 3.3V %s 5.0V %s\n",
+	       sreg,
+	       ( (sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) ? "on" : "off",
+	       (!(sreg & TPS2211_VCCD0) &&  (sreg & TPS2211_VCCD1)) ? "on" : "off"
+	      );
+
+	immap->im_ioport.iop_pcdat = sreg;
+
+	/*  Wait 500 ms; use this to check for over-current */
+	for (i=0; i<5000; ++i) {
+		if ((cp->cp_pbdat & TPS2211_OC) == 0) {
+			printf ("   *** Overcurrent - Safety shutdown ***\n");
+			immap->im_ioport.iop_pcdat &= ~(TPS2211_VCCD0|TPS2211_VCCD1);
+			return (1);
+		}
+		udelay (100);
+	}
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	/* ALl voltages off / Hi-Z */
+	immap->im_ioport.iop_pcdat |= (TPS2211_VPPD0 | TPS2211_VPPD1 |
+			TPS2211_VCCD0 | TPS2211_VCCD1 );
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+	ushort sreg;
+
+	debug ("voltage_set: "
+			PCMCIA_BOARD_MSG
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Configure Port C pins for
+	* 5 Volts Enable and 3 Volts enable,
+	* Turn all power pins to Hi-Z
+	*/
+	debug ("PCMCIA power OFF\n");
+	cfg_ports ();	/* Enables switch, but all in Hi-Z */
+
+	sreg  = immap->im_ioport.iop_pcdat;
+	sreg |= TPS2211_VPPD0 | TPS2211_VPPD1;		/* VAVPP always Hi-Z */
+
+	switch(vcc) {
+		case  0: 			break;	/* Switch off		*/
+		case 33: sreg |=  TPS2211_VCCD0;	/* Switch on 3.3V	*/
+		sreg &= ~TPS2211_VCCD1;
+		break;
+		case 50: sreg &= ~TPS2211_VCCD0;	/* Switch on 5.0V	*/
+		sreg |=  TPS2211_VCCD1;
+		break;
+		default: 			goto done;
+	}
+
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+	       pcmp->pcmc_pipr,
+	       (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+	immap->im_ioport.iop_pcdat = sreg;
+
+#ifdef DEBUG
+{
+	char *s;
+
+	if ((sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) {
+		s = "at 3.3V";
+	} else if (!(sreg & TPS2211_VCCD0) &&  (sreg & TPS2211_VCCD1)) {
+		s = "at 5.0V";
+	} else {
+		s = "down";
+	}
+	printf ("PCMCIA powered %s\n", s);
+}
+#endif
+
+done:
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */
diff --git a/board/cpc45/pd67290.c b/board/cpc45/pd67290.c
index c84fbae918..6ca3e7bd7a 100644
--- a/board/cpc45/pd67290.c
+++ b/board/cpc45/pd67290.c
@@ -1,4 +1,6 @@
-/* pd67290.c - system configuration module for SPD67290
+/*
+ * (C) Copyright 2003-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -18,51 +20,799 @@
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  *
- * (C) 2004 DENX Software Engineering, Heiko Schocher <hs@denx.de>
+ ********************************************************************
+ *
+ * Lots of code copied from:
+ *
+ * i82365.c 1.352 - Linux driver for Intel 82365 and compatible
+ * PC Card controllers, and Yenta-compatible PCI-to-CardBus controllers.
+ * (C) 1999 David A. Hinds <dahinds@users.sourceforge.net>
  */
 
 #include <common.h>
-#include <malloc.h>
-#include <net.h>
-#include <asm/io.h>
+
+#ifdef CONFIG_I82365
+
+#include <command.h>
 #include <pci.h>
+#include <pcmcia.h>
+#include <asm/io.h>
 
-/* imports */
-#include <mpc824x.h>
+#include <pcmcia/ss.h>
+#include <pcmcia/i82365.h>
+#include <pcmcia/yenta.h>
+#include <pcmcia/cirrus.h>
 
 static struct pci_device_id supported[] = {
 	{PCI_VENDOR_ID_CIRRUS, PCI_DEVICE_ID_CIRRUS_6729},
-	{}
+	{0, 0}
+};
+
+#define CYCLE_TIME	120
+
+#ifdef DEBUG
+static void i82365_dump_regions (pci_dev_t dev);
+#endif
+
+typedef struct socket_info_t {
+	pci_dev_t	dev;
+	u_short		bcr;
+	u_char		pci_lat, cb_lat, sub_bus, cache;
+	u_int		cb_phys;
+
+	socket_cap_t	cap;
+	u_short		type;
+	u_int		flags;
+	cirrus_state_t	c_state;
+} socket_info_t;
+
+/* These definitions must match the pcic table! */
+typedef enum pcic_id {
+	IS_PD6710, IS_PD672X, IS_VT83C469
+} pcic_id;
+
+typedef struct pcic_t {
+	char *name;
+} pcic_t;
+
+static pcic_t pcic[] = {
+	{" Cirrus PD6710: "},
+	{" Cirrus PD672x: "},
+	{" VIA VT83C469: "},
 };
 
-/***************************************************************************
-*
-* SPD67290Init -
-*
-* RETURNS: -1 on error, 0 if OK
-*/
+static socket_info_t socket;
+static socket_state_t state;
+static struct pccard_mem_map mem;
+static struct pccard_io_map io;
 
-int SPD67290Init (void)
+/*====================================================================*/
+
+/* Some PCI shortcuts */
+
+static int pci_readb (socket_info_t * s, int r, u_char * v)
+{
+	return pci_read_config_byte (s->dev, r, v);
+}
+static int pci_writeb (socket_info_t * s, int r, u_char v)
+{
+	return pci_write_config_byte (s->dev, r, v);
+}
+static int pci_readw (socket_info_t * s, int r, u_short * v)
+{
+	return pci_read_config_word (s->dev, r, v);
+}
+static int pci_writew (socket_info_t * s, int r, u_short v)
 {
-	pci_dev_t devno;
-	int idx = 0;		/* general index */
-	ulong membaseCsr;	/* base address of device memory space */
+	return pci_write_config_word (s->dev, r, v);
+}
 
-	/* find PD67290 device */
-	if ((devno = pci_find_devices (supported, idx++)) < 0) {
-		printf ("No PD67290 device found !!\n");
+/*====================================================================*/
+
+#define cb_readb(s)		readb((s)->cb_phys + 1)
+#define cb_writeb(s, v)		writeb(v, (s)->cb_phys)
+#define cb_writeb2(s, v)	writeb(v, (s)->cb_phys + 1)
+#define cb_readl(s, r)		readl((s)->cb_phys + (r))
+#define cb_writel(s, r, v)	writel(v, (s)->cb_phys + (r))
+
+
+static u_char i365_get (socket_info_t * s, u_short reg)
+{
+	u_char val;
+#ifdef CONFIG_PCMCIA_SLOT_A
+	int slot = 0;
+#else
+	int slot = 1;
+#endif
+
+	val = I365_REG (slot, reg);
+
+	cb_writeb (s, val);
+	val = cb_readb (s);
+
+	debug ("i365_get slot:%x reg: %x val: %x\n", slot, reg, val);
+	return val;
+}
+
+static void i365_set (socket_info_t * s, u_short reg, u_char data)
+{
+#ifdef CONFIG_PCMCIA_SLOT_A
+	int slot = 0;
+#else
+	int slot = 1;
+#endif
+	u_char val;
+
+	val = I365_REG (slot, reg);
+
+	cb_writeb (s, val);
+	cb_writeb2 (s, data);
+
+	debug ("i365_set slot:%x reg: %x data:%x\n", slot, reg, data);
+}
+
+static void i365_bset (socket_info_t * s, u_short reg, u_char mask)
+{
+	i365_set (s, reg, i365_get (s, reg) | mask);
+}
+
+static void i365_bclr (socket_info_t * s, u_short reg, u_char mask)
+{
+	i365_set (s, reg, i365_get (s, reg) & ~mask);
+}
+
+#if 0	/* not used */
+static void i365_bflip (socket_info_t * s, u_short reg, u_char mask, int b)
+{
+	u_char d = i365_get (s, reg);
+
+	i365_set (s, reg, (b) ? (d | mask) : (d & ~mask));
+}
+
+static u_short i365_get_pair (socket_info_t * s, u_short reg)
+{
+	return (i365_get (s, reg) + (i365_get (s, reg + 1) << 8));
+}
+#endif	/* not used */
+
+static void i365_set_pair (socket_info_t * s, u_short reg, u_short data)
+{
+	i365_set (s, reg, data & 0xff);
+	i365_set (s, reg + 1, data >> 8);
+}
+
+/*======================================================================
+
+    Code to save and restore global state information for Cirrus
+    PD67xx controllers, and to set and report global configuration
+    options.
+
+======================================================================*/
+
+#define flip(v,b,f) (v = ((f)<0) ? v : ((f) ? ((v)|(b)) : ((v)&(~b))))
+
+static void cirrus_get_state (socket_info_t * s)
+{
+	int i;
+	cirrus_state_t *p = &s->c_state;
+
+	p->misc1 = i365_get (s, PD67_MISC_CTL_1);
+	p->misc1 &= (PD67_MC1_MEDIA_ENA | PD67_MC1_INPACK_ENA);
+	p->misc2 = i365_get (s, PD67_MISC_CTL_2);
+	for (i = 0; i < 6; i++)
+		p->timer[i] = i365_get (s, PD67_TIME_SETUP (0) + i);
+
+}
+
+static void cirrus_set_state (socket_info_t * s)
+{
+	int i;
+	u_char misc;
+	cirrus_state_t *p = &s->c_state;
+
+	misc = i365_get (s, PD67_MISC_CTL_2);
+	i365_set (s, PD67_MISC_CTL_2, p->misc2);
+	if (misc & PD67_MC2_SUSPEND)
+		udelay (50000);
+	misc = i365_get (s, PD67_MISC_CTL_1);
+	misc &= ~(PD67_MC1_MEDIA_ENA | PD67_MC1_INPACK_ENA);
+	i365_set (s, PD67_MISC_CTL_1, misc | p->misc1);
+	for (i = 0; i < 6; i++)
+		i365_set (s, PD67_TIME_SETUP (0) + i, p->timer[i]);
+}
+
+static u_int cirrus_set_opts (socket_info_t * s)
+{
+	cirrus_state_t *p = &s->c_state;
+	u_int mask = 0xffff;
+#if DEBUG
+	char buf[200];
+
+	memset (buf, 0, 200);
+#endif
+
+	if (has_ring == -1)
+		has_ring = 1;
+	flip (p->misc2, PD67_MC2_IRQ15_RI, has_ring);
+	flip (p->misc2, PD67_MC2_DYNAMIC_MODE, dynamic_mode);
+#if DEBUG
+	if (p->misc2 & PD67_MC2_IRQ15_RI)
+		strcat (buf, " [ring]");
+	if (p->misc2 & PD67_MC2_DYNAMIC_MODE)
+		strcat (buf, " [dyn mode]");
+	if (p->misc1 & PD67_MC1_INPACK_ENA)
+		strcat (buf, " [inpack]");
+#endif
+
+	if (p->misc2 & PD67_MC2_IRQ15_RI)
+		mask &= ~0x8000;
+	if (has_led > 0) {
+#if DEBUG
+		strcat (buf, " [led]");
+#endif
+		mask &= ~0x1000;
+	}
+	if (has_dma > 0) {
+#if DEBUG
+		strcat (buf, " [dma]");
+#endif
+		mask &= ~0x0600;
+		flip (p->misc2, PD67_MC2_FREQ_BYPASS, freq_bypass);
+#if DEBUG
+		if (p->misc2 & PD67_MC2_FREQ_BYPASS)
+			strcat (buf, " [freq bypass]");
+#endif
+	}
+
+	if (setup_time >= 0)
+		p->timer[0] = p->timer[3] = setup_time;
+	if (cmd_time > 0) {
+		p->timer[1] = cmd_time;
+		p->timer[4] = cmd_time * 2 + 4;
+	}
+	if (p->timer[1] == 0) {
+		p->timer[1] = 6;
+		p->timer[4] = 16;
+		if (p->timer[0] == 0)
+			p->timer[0] = p->timer[3] = 1;
+	}
+	if (recov_time >= 0)
+		p->timer[2] = p->timer[5] = recov_time;
+
+	debug ("i82365 Opt: %s [%d/%d/%d] [%d/%d/%d]\n",
+		buf,
+		p->timer[0], p->timer[1], p->timer[2],
+		p->timer[3], p->timer[4], p->timer[5]);
+
+	return mask;
+}
+
+/*======================================================================
+
+    Routines to handle common CardBus options
+
+======================================================================*/
+
+/* Default settings for PCI command configuration register */
+#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
+		  PCI_COMMAND_MASTER|PCI_COMMAND_WAIT)
+
+static void cb_get_state (socket_info_t * s)
+{
+	pci_readb (s, PCI_CACHE_LINE_SIZE, &s->cache);
+	pci_readb (s, PCI_LATENCY_TIMER, &s->pci_lat);
+	pci_readb (s, CB_LATENCY_TIMER, &s->cb_lat);
+	pci_readb (s, CB_CARDBUS_BUS, &s->cap.cardbus);
+	pci_readb (s, CB_SUBORD_BUS, &s->sub_bus);
+	pci_readw (s, CB_BRIDGE_CONTROL, &s->bcr);
+}
+
+static void cb_set_state (socket_info_t * s)
+{
+	pci_writew (s, PCI_COMMAND, CMD_DFLT);
+	pci_writeb (s, PCI_CACHE_LINE_SIZE, s->cache);
+	pci_writeb (s, PCI_LATENCY_TIMER, s->pci_lat);
+	pci_writeb (s, CB_LATENCY_TIMER, s->cb_lat);
+	pci_writeb (s, CB_CARDBUS_BUS, s->cap.cardbus);
+	pci_writeb (s, CB_SUBORD_BUS, s->sub_bus);
+	pci_writew (s, CB_BRIDGE_CONTROL, s->bcr);
+}
+
+static void cb_set_opts (socket_info_t * s)
+{
+}
+
+/*======================================================================
+
+    Power control for Cardbus controllers: used both for 16-bit and
+    Cardbus cards.
+
+======================================================================*/
+
+static int cb_set_power (socket_info_t * s, socket_state_t * state)
+{
+	u_int reg = 0;
+
+	reg = I365_PWR_NORESET;
+	if (state->flags & SS_PWR_AUTO)
+		reg |= I365_PWR_AUTO;
+	if (state->flags & SS_OUTPUT_ENA)
+		reg |= I365_PWR_OUT;
+	if (state->Vpp != 0) {
+		if (state->Vpp == 120) {
+			reg |= I365_VPP1_12V;
+			puts (" 12V card found: ");
+		} else if (state->Vpp == state->Vcc) {
+			reg |= I365_VPP1_5V;
+		} else {
+			puts (" power not found: ");
+			return -1;
+		}
+	}
+	if (state->Vcc != 0) {
+		reg |= I365_VCC_5V;
+		if (state->Vcc == 33) {
+			puts (" 3.3V card found: ");
+			i365_bset (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
+		} else if (state->Vcc == 50) {
+			puts (" 5V card found: ");
+			i365_bclr (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
+		} else {
+			puts (" power not found: ");
+			return -1;
+		}
+	}
+
+	if (reg != i365_get (s, I365_POWER)) {
+		reg = (I365_PWR_OUT | I365_PWR_NORESET | I365_VCC_5V | I365_VPP1_5V);
+		i365_set (s, I365_POWER, reg);
+	}
+
+	return 0;
+}
+
+/*======================================================================
+
+    Generic routines to get and set controller options
+
+======================================================================*/
+
+static void get_bridge_state (socket_info_t * s)
+{
+	cirrus_get_state (s);
+	cb_get_state (s);
+}
+
+static void set_bridge_state (socket_info_t * s)
+{
+	cb_set_state (s);
+	i365_set (s, I365_GBLCTL, 0x00);
+	i365_set (s, I365_GENCTL, 0x00);
+	cirrus_set_state (s);
+}
+
+static void set_bridge_opts (socket_info_t * s)
+{
+	cirrus_set_opts (s);
+	cb_set_opts (s);
+}
+
+/*====================================================================*/
+#define PD67_EXT_INDEX		0x2e	/* Extension index */
+#define PD67_EXT_DATA		0x2f	/* Extension data */
+#define PD67_EXD_VS1(s)		(0x01 << ((s)<<1))
+
+#define pd67_ext_get(s, r) \
+    (i365_set(s, PD67_EXT_INDEX, r), i365_get(s, PD67_EXT_DATA))
+
+static int i365_get_status (socket_info_t * s, u_int * value)
+{
+	u_int status;
+	u_char val;
+	u_char power, vcc, vpp;
+	u_int powerstate;
+
+	status = i365_get (s, I365_IDENT);
+	status = i365_get (s, I365_STATUS);
+	*value = ((status & I365_CS_DETECT) == I365_CS_DETECT) ? SS_DETECT : 0;
+	if (i365_get (s, I365_INTCTL) & I365_PC_IOCARD) {
+		*value |= (status & I365_CS_STSCHG) ? 0 : SS_STSCHG;
+	} else {
+		*value |= (status & I365_CS_BVD1) ? 0 : SS_BATDEAD;
+		*value |= (status & I365_CS_BVD2) ? 0 : SS_BATWARN;
+	}
+	*value |= (status & I365_CS_WRPROT) ? SS_WRPROT : 0;
+	*value |= (status & I365_CS_READY) ? SS_READY : 0;
+	*value |= (status & I365_CS_POWERON) ? SS_POWERON : 0;
+
+	/* Check for Cirrus CL-PD67xx chips */
+	i365_set (s, PD67_CHIP_INFO, 0);
+	val = i365_get (s, PD67_CHIP_INFO);
+	s->type = -1;
+	if ((val & PD67_INFO_CHIP_ID) == PD67_INFO_CHIP_ID) {
+		val = i365_get (s, PD67_CHIP_INFO);
+		if ((val & PD67_INFO_CHIP_ID) == 0) {
+			s->type = (val & PD67_INFO_SLOTS) ? IS_PD672X : IS_PD6710;
+			i365_set (s, PD67_EXT_INDEX, 0xe5);
+			if (i365_get (s, PD67_EXT_INDEX) != 0xe5)
+				s->type = IS_VT83C469;
+		}
+	} else {
+		printf ("no Cirrus Chip found\n");
+		*value = 0;
 		return -1;
 	}
-	/* - 0xfe000000 see MPC 8245 Users Manual Adress Map B */
-	membaseCsr = PCMCIA_IO_BASE - 0xfe000000;
+
+	power = i365_get (s, I365_POWER);
+	state.flags |= (power & I365_PWR_AUTO) ? SS_PWR_AUTO : 0;
+	state.flags |= (power & I365_PWR_OUT) ? SS_OUTPUT_ENA : 0;
+	vcc = power & I365_VCC_MASK;
+	vpp = power & I365_VPP1_MASK;
+	state.Vcc = state.Vpp = 0;
+	if((vcc== 0) || (vpp == 0)) {
+		/*
+		 * On the Cirrus we get the info which card voltage
+		 * we have in EXTERN DATA and write it to MISC_CTL1
+		 */
+		powerstate = pd67_ext_get(s, PD67_EXTERN_DATA);
+		if (powerstate & PD67_EXD_VS1(0)) {
+			/* 5V Card */
+			i365_bclr (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
+		} else {
+			/* 3.3V Card */
+			i365_bset (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
+		}
+		i365_set (s, I365_POWER, (I365_PWR_OUT | I365_PWR_NORESET | I365_VCC_5V | I365_VPP1_5V));
+		power = i365_get (s, I365_POWER);
+	}
+	if (power & I365_VCC_5V) {
+		state.Vcc = (i365_get(s, PD67_MISC_CTL_1) & PD67_MC1_VCC_3V) ? 33 : 50;
+	}
+
+	if (power == I365_VPP1_12V)
+		state.Vpp = 120;
+
+	/* IO card, RESET flags, IO interrupt */
+	power = i365_get (s, I365_INTCTL);
+	state.flags |= (power & I365_PC_RESET) ? 0 : SS_RESET;
+	if (power & I365_PC_IOCARD)
+		state.flags |= SS_IOCARD;
+	state.io_irq = power & I365_IRQ_MASK;
+
+	/* Card status change mask */
+	power = i365_get (s, I365_CSCINT);
+	state.csc_mask = (power & I365_CSC_DETECT) ? SS_DETECT : 0;
+	if (state.flags & SS_IOCARD)
+		state.csc_mask |= (power & I365_CSC_STSCHG) ? SS_STSCHG : 0;
+	else {
+		state.csc_mask |= (power & I365_CSC_BVD1) ? SS_BATDEAD : 0;
+		state.csc_mask |= (power & I365_CSC_BVD2) ? SS_BATWARN : 0;
+		state.csc_mask |= (power & I365_CSC_READY) ? SS_READY : 0;
+	}
+	debug ("i82365: GetStatus(0) = flags %#3.3x, Vcc %d, Vpp %d, "
+		"io_irq %d, csc_mask %#2.2x\n", state.flags,
+		state.Vcc, state.Vpp, state.io_irq, state.csc_mask);
+
+	return 0;
+}	/* i365_get_status */
+
+static int i365_set_socket (socket_info_t * s, socket_state_t * state)
+{
+	u_char reg;
+
+	set_bridge_state (s);
+
+	/* IO card, RESET flag */
+	reg = 0;
+	reg |= (state->flags & SS_RESET) ? 0 : I365_PC_RESET;
+	reg |= (state->flags & SS_IOCARD) ? I365_PC_IOCARD : 0;
+	i365_set (s, I365_INTCTL, reg);
+
+	cb_set_power (s, state);
+
+#if 0
+	/* Card status change interrupt mask */
+	reg = s->cs_irq << 4;
+	if (state->csc_mask & SS_DETECT)
+		reg |= I365_CSC_DETECT;
+	if (state->flags & SS_IOCARD) {
+		if (state->csc_mask & SS_STSCHG)
+			reg |= I365_CSC_STSCHG;
+	} else {
+		if (state->csc_mask & SS_BATDEAD)
+			reg |= I365_CSC_BVD1;
+		if (state->csc_mask & SS_BATWARN)
+			reg |= I365_CSC_BVD2;
+		if (state->csc_mask & SS_READY)
+			reg |= I365_CSC_READY;
+	}
+	i365_set (s, I365_CSCINT, reg);
+	i365_get (s, I365_CSC);
+#endif	/* 0 */
+
+	return 0;
+}	/* i365_set_socket */
+
+/*====================================================================*/
+
+static int i365_set_mem_map (socket_info_t * s, struct pccard_mem_map *mem)
+{
+	u_short base, i;
+	u_char map;
+
+	debug ("i82365: SetMemMap(%d, %#2.2x, %d ns, %#5.5lx-%#5.5lx, %#5.5x)\n",
+		mem->map, mem->flags, mem->speed,
+		mem->sys_start, mem->sys_stop, mem->card_start);
+
+	map = mem->map;
+	if ((map > 4) ||
+	    (mem->card_start > 0x3ffffff) ||
+	    (mem->sys_start > mem->sys_stop) ||
+	    (mem->speed > 1000)) {
+		return -1;
+	}
+
+	/* Turn off the window before changing anything */
+	if (i365_get (s, I365_ADDRWIN) & I365_ENA_MEM (map))
+		i365_bclr (s, I365_ADDRWIN, I365_ENA_MEM (map));
+
+	/* Take care of high byte, for PCI controllers */
+	i365_set (s, CB_MEM_PAGE (map), mem->sys_start >> 24);
+
+	base = I365_MEM (map);
+	i = (mem->sys_start >> 12) & 0x0fff;
+	if (mem->flags & MAP_16BIT)
+		i |= I365_MEM_16BIT;
+	if (mem->flags & MAP_0WS)
+		i |= I365_MEM_0WS;
+	i365_set_pair (s, base + I365_W_START, i);
+
+	i = (mem->sys_stop >> 12) & 0x0fff;
+	switch (mem->speed / CYCLE_TIME) {
+	case 0:
+		break;
+	case 1:
+		i |= I365_MEM_WS0;
+		break;
+	case 2:
+		i |= I365_MEM_WS1;
+		break;
+	default:
+		i |= I365_MEM_WS1 | I365_MEM_WS0;
+		break;
+	}
+	i365_set_pair (s, base + I365_W_STOP, i);
+
+	i = 0;
+	if (mem->flags & MAP_WRPROT)
+		i |= I365_MEM_WRPROT;
+	if (mem->flags & MAP_ATTRIB)
+		i |= I365_MEM_REG;
+	i365_set_pair (s, base + I365_W_OFF, i);
+
+	/* set System Memory map Upper Adress */
+	i365_set(s, PD67_EXT_INDEX, PD67_MEM_PAGE(map));
+	i365_set(s, PD67_EXT_DATA, ((mem->sys_start >> 24) & 0xff));
+
+	/* Turn on the window if necessary */
+	if (mem->flags & MAP_ACTIVE)
+		i365_bset (s, I365_ADDRWIN, I365_ENA_MEM (map));
+	return 0;
+}	/* i365_set_mem_map */
+
+static int i365_set_io_map (socket_info_t * s, struct pccard_io_map *io)
+{
+	u_char map, ioctl;
+
+	map = io->map;
+	/* comment out: comparison is always false due to limited range of data type */
+	if ((map > 1) || /* (io->start > 0xffff) || (io->stop > 0xffff) || */
+	    (io->stop < io->start))
+		return -1;
+	/* Turn off the window before changing anything */
+	if (i365_get (s, I365_ADDRWIN) & I365_ENA_IO (map))
+		i365_bclr (s, I365_ADDRWIN, I365_ENA_IO (map));
+	i365_set_pair (s, I365_IO (map) + I365_W_START, io->start);
+	i365_set_pair (s, I365_IO (map) + I365_W_STOP, io->stop);
+	ioctl = i365_get (s, I365_IOCTL) & ~I365_IOCTL_MASK (map);
+	if (io->speed)
+		ioctl |= I365_IOCTL_WAIT (map);
+	if (io->flags & MAP_0WS)
+		ioctl |= I365_IOCTL_0WS (map);
+	if (io->flags & MAP_16BIT)
+		ioctl |= I365_IOCTL_16BIT (map);
+	if (io->flags & MAP_AUTOSZ)
+		ioctl |= I365_IOCTL_IOCS16 (map);
+	i365_set (s, I365_IOCTL, ioctl);
+	/* Turn on the window if necessary */
+	if (io->flags & MAP_ACTIVE)
+		i365_bset (s, I365_ADDRWIN, I365_ENA_IO (map));
+	return 0;
+}	/* i365_set_io_map */
+
+/*====================================================================*/
+
+/*
+ * PCI_ADDR = (HOST_ADDR - 0xfe000000)
+ * see MPC 8245 Users Manual Adress Map B
+ */
+#define	HOST_TO_PCI(addr)	((addr) - 0xfe000000)
+#define	PCI_TO_HOST(addr)	((addr) + 0xfe000000)
+
+int i82365_init (void)
+{
+	u_int val;
+	int i;
+
+	if ((socket.dev = pci_find_devices (supported, 0)) < 0) {
+		/* Controller not found */
+		printf ("No PD67290 device found !!\n");
+		return 1;
+	}
+	debug ("i82365 Device Found!\n");
+
+	socket.cb_phys = PCMCIA_IO_BASE;
 
 	/* set base address */
-	pci_write_config_dword (devno, PCI_BASE_ADDRESS_0, membaseCsr);
+	pci_write_config_dword (socket.dev, PCI_BASE_ADDRESS_0,
+		HOST_TO_PCI(socket.cb_phys));
 
 	/* enable mapped memory and IO addresses */
-	pci_write_config_dword (devno,
+	pci_write_config_dword (socket.dev,
 				PCI_COMMAND,
 				PCI_COMMAND_MEMORY |
 				PCI_COMMAND_IO | PCI_COMMAND_WAIT);
+
+	get_bridge_state (&socket);
+	set_bridge_opts (&socket);
+
+	i = i365_get_status (&socket, &val);
+
+	if (i > -1) {
+		puts (pcic[socket.type].name);
+	} else {
+		printf ("i82365: Controller not found.\n");
+		return 1;
+	}
+	if((val & SS_DETECT) != SS_DETECT){
+		puts ("No card\n");
+		return 1;
+	}
+
+	state.flags |= SS_OUTPUT_ENA;
+
+	i365_set_socket (&socket, &state);
+
+	for (i = 500; i; i--) {
+		if ((i365_get (&socket, I365_STATUS) & I365_CS_READY))
+			break;
+		udelay (1000);
+	}
+
+	if (i == 0) {
+		/* PC Card not ready for data transfer */
+		puts ("i82365 PC Card not ready for data transfer\n");
+		return 1;
+	}
+	debug (" PC Card ready for data transfer: ");
+
+	mem.map = 0;
+	mem.flags = MAP_ATTRIB | MAP_ACTIVE;
+	mem.speed = 300;
+	mem.sys_start = CFG_PCMCIA_MEM_ADDR;
+	mem.sys_stop = CFG_PCMCIA_MEM_ADDR + CFG_PCMCIA_MEM_SIZE - 1;
+	mem.card_start = 0;
+	i365_set_mem_map (&socket, &mem);
+
+	mem.map = 1;
+	mem.flags = MAP_ACTIVE;
+	mem.speed = 300;
+	mem.sys_start = CFG_PCMCIA_MEM_ADDR + CFG_PCMCIA_MEM_SIZE;
+	mem.sys_stop = CFG_PCMCIA_MEM_ADDR + (2 * CFG_PCMCIA_MEM_SIZE) - 1;
+	mem.card_start = 0;
+	i365_set_mem_map (&socket, &mem);
+
+#ifdef DEBUG
+	i82365_dump_regions (socket.dev);
+#endif
+
 	return 0;
 }
+
+void i82365_exit (void)
+{
+	io.map = 0;
+	io.flags = 0;
+	io.speed = 0;
+	io.start = 0;
+	io.stop = 0x1;
+
+	i365_set_io_map (&socket, &io);
+
+	mem.map = 0;
+	mem.flags = 0;
+	mem.speed = 0;
+	mem.sys_start = 0;
+	mem.sys_stop = 0x1000;
+	mem.card_start = 0;
+
+	i365_set_mem_map (&socket, &mem);
+
+	mem.map = 1;
+	mem.flags = 0;
+	mem.speed = 0;
+	mem.sys_start = 0;
+	mem.sys_stop = 0x1000;
+	mem.card_start = 0;
+
+	i365_set_mem_map (&socket, &mem);
+
+	state.Vcc = state.Vpp = 0;
+
+	i365_set_socket (&socket, &state);
+}
+
+int pcmcia_on (void)
+{
+	u_int rc;
+
+	debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+	rc = i82365_init();
+	if (rc)
+		goto exit;
+
+	rc = check_ide_device(0);
+	if (rc == 0)
+		goto exit;
+
+	i82365_exit();
+
+exit:
+	return rc;
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_off (void)
+{
+	printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+	i82365_exit();
+
+	return 0;
+}
+#endif
+
+/*======================================================================
+
+    Debug stuff
+
+======================================================================*/
+
+#ifdef DEBUG
+static void i82365_dump_regions (pci_dev_t dev)
+{
+	u_int tmp[2];
+	u_int *mem = (void *) socket.cb_phys;
+	u_char *cis = (void *) CFG_PCMCIA_MEM_ADDR;
+	u_char *ide = (void *) (CFG_ATA_BASE_ADDR + CFG_ATA_REG_OFFSET);
+
+	pci_read_config_dword (dev, 0x00, tmp + 0);
+	pci_read_config_dword (dev, 0x80, tmp + 1);
+
+	printf ("PCI CONF: %08X ... %08X\n",
+		tmp[0], tmp[1]);
+	printf ("PCI MEM:  ... %08X ... %08X\n",
+		mem[0x8 / 4], mem[0x800 / 4]);
+	printf ("CIS:      ...%c%c%c%c%c%c%c%c...\n",
+		cis[0x38], cis[0x3a], cis[0x3c], cis[0x3e],
+		cis[0x40], cis[0x42], cis[0x44], cis[0x48]);
+	printf ("CIS CONF: %02X %02X %02X ...\n",
+		cis[0x200], cis[0x202], cis[0x204]);
+	printf ("IDE:      %02X %02X %02X %02X %02X %02X %02X %02X\n",
+		ide[0], ide[1], ide[2], ide[3],
+		ide[4], ide[5], ide[6], ide[7]);
+}
+#endif	/* DEBUG */
+
+#endif /* CONFIG_I82365 */
diff --git a/board/fads/Makefile b/board/fads/Makefile
index baa6c2e40b..7fc88ee824 100644
--- a/board/fads/Makefile
+++ b/board/fads/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o lamp.o
+OBJS	= $(BOARD).o flash.o lamp.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/fads/pcmcia.c b/board/fads/pcmcia.c
new file mode 100644
index 0000000000..978c16b941
--- /dev/null
+++ b/board/fads/pcmcia.c
@@ -0,0 +1,84 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#ifdef	CONFIG_ADS
+#define	PCMCIA_BOARD_MSG "ADS"
+#else
+#define	PCMCIA_BOARD_MSG "FADS"
+#endif
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	u_long reg = 0;
+
+	switch(vpp) {
+		case 0: reg = 0; break;
+		case 50: reg = 1; break;
+		case 120: reg = 2; break;
+		default: return 1;
+	}
+
+	switch(vcc) {
+		case 0: reg = 0; break;
+#ifdef CONFIG_ADS
+	case 50: reg = BCSR1_PCCVCCON; break;
+#endif
+#ifdef CONFIG_FADS
+	case 33: reg = BCSR1_PCCVCC0 | BCSR1_PCCVCC1; break;
+	case 50: reg = BCSR1_PCCVCC1; break;
+#endif
+	default: return 1;
+	}
+
+	/* first, turn off all power */
+
+#ifdef CONFIG_ADS
+	*((uint *)BCSR1) |= BCSR1_PCCVCCON;
+#endif
+#ifdef CONFIG_FADS
+	*((uint *)BCSR1) &= ~(BCSR1_PCCVCC0 | BCSR1_PCCVCC1);
+#endif
+	*((uint *)BCSR1) &= ~BCSR1_PCCVPP_MASK;
+
+	/* enable new powersettings */
+
+#ifdef CONFIG_ADS
+	*((uint *)BCSR1) &= ~reg;
+#endif
+#ifdef CONFIG_FADS
+	*((uint *)BCSR1) |= reg;
+#endif
+
+ 	*((uint *)BCSR1) |= reg << 20;
+
+	return 0;
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+	*((uint *)BCSR1) &= ~BCSR1_PCCEN;
+	return 0;
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	*((uint *)BCSR1) &= ~BCSR1_PCCEN;
+	return 0;
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+#endif	/* CONFIG_PCMCIA */
diff --git a/board/gth/Makefile b/board/gth/Makefile
index e14c12e4aa..48f74cd94d 100644
--- a/board/gth/Makefile
+++ b/board/gth/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o ee_access.o
+OBJS	= $(BOARD).o flash.o ee_access.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/gth/pcmcia.c b/board/gth/pcmcia.c
new file mode 100644
index 0000000000..fce5492635
--- /dev/null
+++ b/board/gth/pcmcia.c
@@ -0,0 +1,93 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "GTH COMPACT FLASH"
+
+int pcmcia_voltage_set (int slot, int vcc, int vpp)
+{	/* Do nothing */
+	return 0;
+}
+
+int pcmcia_hardware_enable (int slot)
+{
+	volatile immap_t *immap;
+	volatile cpm8xx_t *cp;
+	volatile pcmconf8xx_t *pcmp;
+	volatile sysconf8xx_t *sysp;
+	uint reg, mask;
+
+	debug ("hardware_enable: GTH Slot %c\n", 'A' + slot);
+
+	immap = (immap_t *) CFG_IMMR;
+	sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
+	pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
+	cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;	/* active low  */
+	PCMCIA_PGCRX (_slot_) = reg;
+	udelay (500);
+
+	/*
+	* Make sure there is a card in the slot,
+	* then configure the interface.
+	*/
+	udelay (10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__, __FUNCTION__,
+	       &(pcmp->pcmc_pipr), pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & 0x98000000) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	mask = PCMCIA_VS1 (slot) | PCMCIA_VS2 (slot);
+	reg = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       reg,
+	       (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
+	       (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX (_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX (_slot_) = reg;
+
+	udelay (250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return 0;
+}
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	return 0;	/* No hardware to disable */
+}
+#endif
+
+#endif	/* CONFIG_PCMCIA */
diff --git a/board/icu862/Makefile b/board/icu862/Makefile
index 7a2014d466..7b2b545820 100644
--- a/board/icu862/Makefile
+++ b/board/icu862/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o
+OBJS	= $(BOARD).o flash.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/icu862/pcmcia.c b/board/icu862/pcmcia.c
new file mode 100644
index 0000000000..20f653ba2b
--- /dev/null
+++ b/board/icu862/pcmcia.c
@@ -0,0 +1,268 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "ICU862"
+
+static void cfg_port_B (void)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	uint reg;
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	* Configure Port B for TPS2205 PC-Card Power-Interface Switch
+	*
+	* Switch off all voltages, assert shutdown
+	*/
+	reg  = cp->cp_pbdat;
+	reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */
+			TPS2205_VCC3    | TPS2205_VCC5    |	/* VAVCC => Hi-Z */
+			TPS2205_SHDN);				/* enable switch */
+	cp->cp_pbdat = reg;
+
+	cp->cp_pbpar &= ~(TPS2205_INPUTS | TPS2205_OUTPUTS);
+
+	reg = cp->cp_pbdir & ~(TPS2205_INPUTS);
+	cp->cp_pbdir = reg | TPS2205_OUTPUTS;
+
+	debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
+	       cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, pipr, mask;
+	int i;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/* Configure Port B for TPS2205 PC-Card Power-Interface Switch */
+	cfg_port_B ();
+
+	/*
+	* Configure SIUMCR to enable PCMCIA port B
+	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	*/
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
+	*/
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	pipr = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       pipr,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+
+	reg  = cp->cp_pbdat;
+	if ((pipr & mask) == mask) {
+		reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */
+				TPS2205_VCC3);				/* 3V off	*/
+		reg &= ~(TPS2205_VCC5);				/* 5V on	*/
+		puts (" 5.0V card found: ");
+	} else {
+		reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */
+				TPS2205_VCC5);				/* 5V off	*/
+		reg &= ~(TPS2205_VCC3);				/* 3V on	*/
+		puts (" 3.3V card found: ");
+	}
+
+	debug ("\nPB DAT: %08x -> 3.3V %s 5.0V %s VPP_PGM %s VPP_VCC %s\n",
+	       reg,
+	       (reg & TPS2205_VCC3)    ? "off" : "on",
+	       (reg & TPS2205_VCC5)    ? "off" : "on",
+	       (reg & TPS2205_VPP_PGM) ? "off" : "on",
+	       (reg & TPS2205_VPP_VCC) ? "off" : "on" );
+
+	cp->cp_pbdat = reg;
+
+	/*  Wait 500 ms; use this to check for over-current */
+	for (i=0; i<5000; ++i) {
+		if ((cp->cp_pbdat & TPS2205_OC) == 0) {
+			printf ("   *** Overcurrent - Safety shutdown ***\n");
+			cp->cp_pbdat &= ~(TPS2205_SHDN);
+			return (1);
+		}
+		udelay (100);
+	}
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+	/* Shut down */
+	cp->cp_pbdat &= ~(TPS2205_SHDN);
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("voltage_set: "
+			PCMCIA_BOARD_MSG
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Configure Port C pins for
+	* 5 Volts Enable and 3 Volts enable,
+	* Turn all power pins to Hi-Z
+	*/
+	debug ("PCMCIA power OFF\n");
+	cfg_port_B ();	/* Enables switch, but all in Hi-Z */
+
+	reg  = cp->cp_pbdat;
+
+	switch(vcc) {
+		case  0: 			break;	/* Switch off		*/
+		case 33: reg &= ~TPS2205_VCC3;	break;	/* Switch on 3.3V	*/
+		case 50: reg &= ~TPS2205_VCC5;	break;	/* Switch on 5.0V	*/
+		default: 			goto done;
+	}
+
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+	       pcmp->pcmc_pipr,
+	       (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+	cp->cp_pbdat = reg;
+
+#ifdef DEBUG
+{
+	char *s;
+
+	if ((reg & TPS2205_VCC3) == 0) {
+		s = "at 3.3V";
+	} else if ((reg & TPS2205_VCC5) == 0) {
+		s = "at 5.0V";
+	} else {
+		s = "down";
+	}
+	printf ("PCMCIA powered %s\n", s);
+}
+#endif
+
+done:
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */
diff --git a/board/kup/common/pcmcia.c b/board/kup/common/pcmcia.c
new file mode 100644
index 0000000000..1f61a0ecd1
--- /dev/null
+++ b/board/kup/common/pcmcia.c
@@ -0,0 +1,225 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "KUP"
+
+#define KUP4K_PCMCIA_B_3V3 (0x00020000)
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, mask;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	* Configure SIUMCR to enable PCMCIA port B
+	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	*/
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(slot);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+	udelay(2500);
+
+	/*
+	* Configure Port B pins for
+	* 3 Volts enable
+	*/
+	if (slot) { /* Slot A is built-in */
+		cp->cp_pbdir |=  KUP4K_PCMCIA_B_3V3;
+		cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
+		/* remove all power */
+		cp->cp_pbdat |=  KUP4K_PCMCIA_B_3V3; /* active low */
+	}
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On.
+	*/
+	printf("%s  Slot %c:", slot ? "" : "\n", 'A' + slot);
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	reg  = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       reg,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+	if ((reg & mask) == mask) {
+		puts (" 5.0V card found: NOT SUPPORTED !!!\n");
+	} else {
+		if(slot)
+			cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
+		puts (" 3.3V card found: ");
+	}
+#if 0
+	/*  VCC switch error flag, PCMCIA slot INPACK_ pin */
+	cp->cp_pbdir &= ~(0x0020 | 0x0010);
+	cp->cp_pbpar &= ~(0x0020 | 0x0010);
+	udelay(500000);
+#endif
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(slot);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/* remove all power */
+	if (slot)
+		cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3;
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("voltage_set: "	\
+			PCMCIA_BOARD_MSG	\
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	if (!slot) /* Slot A is not configurable */
+		return 0;
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(slot);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+	udelay(500);
+
+	debug ("PCMCIA power OFF\n");
+	/*
+	* Configure Port B pins for
+	* 3 Volts enable
+	*/
+	cp->cp_pbdir |=  KUP4K_PCMCIA_B_3V3;
+	cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
+	/* remove all power */
+	cp->cp_pbdat |=  KUP4K_PCMCIA_B_3V3; /* active low */
+
+	switch(vcc) {
+		case  0: 		break;
+		case 33:
+			cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
+			debug ("PCMCIA powered at 3.3V\n");
+			break;
+		case 50:
+			debug ("PCMCIA: 5Volt vcc not supported\n");
+			break;
+		default:
+			puts("PCMCIA: vcc not supported");
+			break;
+	}
+	udelay(10000);
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+	       pcmp->pcmc_pipr,
+	       (pcmp->pcmc_pipr & (0x80000000 >> (slot << 4)))
+			       ? "only 5 V --> NOT SUPPORTED"
+	: "can do 3.3V");
+
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(slot);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */
diff --git a/board/kup/kup4k/Makefile b/board/kup/kup4k/Makefile
index 62d289b436..4a3954c389 100644
--- a/board/kup/kup4k/Makefile
+++ b/board/kup/kup4k/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o
+OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o ../common/pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/kup/kup4x/Makefile b/board/kup/kup4x/Makefile
index 62d289b436..4a3954c389 100644
--- a/board/kup/kup4x/Makefile
+++ b/board/kup/kup4x/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o
+OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o ../common/pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/lwmon/Makefile b/board/lwmon/Makefile
index 7a2014d466..7b2b545820 100644
--- a/board/lwmon/Makefile
+++ b/board/lwmon/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o
+OBJS	= $(BOARD).o flash.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/lwmon/pcmcia.c b/board/lwmon/pcmcia.c
new file mode 100644
index 0000000000..2349286bb2
--- /dev/null
+++ b/board/lwmon/pcmcia.c
@@ -0,0 +1,240 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+#include <i2c.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "LWMON"
+
+/* #define's for MAX1604 Power Switch */
+#define MAX1604_OP_SUS		0x80
+#define MAX1604_VCCBON		0x40
+#define MAX1604_VCC_35		0x20
+#define MAX1604_VCCBHIZ		0x10
+#define MAX1604_VPPBON		0x08
+#define MAX1604_VPPBPBPGM	0x04
+#define MAX1604_VPPBHIZ		0x02
+/* reserved			0x01	*/
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, mask;
+	uchar val;
+
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	/* Switch on PCMCIA port in PIC register 0x60 */
+	reg = pic_read  (0x60);
+	debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
+	reg &= ~0x10;
+	/* reg |= 0x08; Vpp not needed */
+	pic_write (0x60, reg);
+#ifdef DEBUG
+	reg = pic_read  (0x60);
+	printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
+#endif
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	 * Configure SIUMCR to enable PCMCIA port B
+	 * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	 */
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	 * Disable interrupts, DMA, and PCMCIA buffers
+	 * (isolate the interface) and assert RESET signal
+	 */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	 * Make sure there is a card in the slot, then configure the interface.
+	 */
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+		__LINE__,__FUNCTION__,
+		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	 * Power On.
+	 */
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	reg  = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+		reg,
+		(reg&PCMCIA_VS1(slot))?"n":"ff",
+		(reg&PCMCIA_VS2(slot))?"n":"ff");
+	if ((reg & mask) == mask) {
+		val = 0;		/* VCCB3/5 = 0 ==> use Vx = 5.0 V */
+		puts (" 5.0V card found: ");
+	} else {
+		val = MAX1604_VCC_35;	/* VCCB3/5 = 1 ==> use Vy = 3.3 V */
+		puts (" 3.3V card found: ");
+	}
+
+	/*  switch VCC on */
+	val |= MAX1604_OP_SUS | MAX1604_VCCBON;
+	i2c_init  (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+	i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+
+	udelay(500000);
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+	uchar val;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+	/* remove all power, put output in high impedance state */
+	val  = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
+	i2c_init  (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+	i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	/* Switch off PCMCIA port in PIC register 0x60 */
+	reg = pic_read  (0x60);
+	debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
+	reg |=  0x10;
+	reg &= ~0x08;
+	pic_write (0x60, reg);
+#ifdef DEBUG
+	reg = pic_read  (0x60);
+	printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
+#endif
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+	uchar val;
+
+	debug ("voltage_set: "
+		PCMCIA_BOARD_MSG
+		" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+		'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	/*
+	 * Disable PCMCIA buffers (isolate the interface)
+	 * and assert RESET signal
+	 */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	 * Turn off all power (switch to high impedance)
+	 */
+	debug ("PCMCIA power OFF\n");
+	val  = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
+	i2c_init  (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+	i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+
+	val = 0;
+	switch(vcc) {
+	case  0: 			break;
+	case 33: val = MAX1604_VCC_35;	break;
+	case 50: 			break;
+	default: 			goto done;
+	}
+
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+		pcmp->pcmc_pipr,
+		(pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+	i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+	if (val) {
+		debug ("PCMCIA powered at %sV\n",
+			(val & MAX1604_VCC_35) ? "3.3" : "5.0");
+	} else {
+		debug ("PCMCIA powered down\n");
+	}
+
+done:
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+		slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */
diff --git a/board/mbx8xx/Makefile b/board/mbx8xx/Makefile
index 3e8376cc0d..e4d10994ed 100644
--- a/board/mbx8xx/Makefile
+++ b/board/mbx8xx/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o vpd.o
+OBJS	= $(BOARD).o flash.o vpd.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/mbx8xx/pcmcia.c b/board/mbx8xx/pcmcia.c
new file mode 100644
index 0000000000..132a68806d
--- /dev/null
+++ b/board/mbx8xx/pcmcia.c
@@ -0,0 +1,166 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#include "csr.h"
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+/* A lot of this has been taken from the RPX code in this file it works from me.
+   I have added the voltage selection for the MBX board. */
+
+/* MBX voltage bit in control register #2 */
+#define CR2_VPP12       ((uchar)0x10)
+#define CR2_VPPVDD      ((uchar)0x20)
+#define CR2_VDD5        ((uchar)0x40)
+#define CR2_VDD3        ((uchar)0x80)
+
+#define PCMCIA_BOARD_MSG "MBX860"
+
+int pcmcia_voltage_set (int slot, int vcc, int vpp)
+{
+	uchar reg = 0;
+
+	debug ("voltage_set: PCMCIA_BOARD_MSG Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	       'A' + slot, vcc / 10, vcc % 10, vpp / 10, vcc % 10);
+
+	switch (vcc) {
+		case 0:
+			break;
+		case 33:
+			reg |= CR2_VDD3;
+			break;
+		case 50:
+			reg |= CR2_VDD5;
+			break;
+		default:
+			return 1;
+	}
+
+	switch (vpp) {
+		case 0:
+			break;
+		case 33:
+		case 50:
+			if (vcc == vpp) {
+				reg |= CR2_VPPVDD;
+			} else {
+				return 1;
+			}
+			break;
+		case 120:
+			reg |= CR2_VPP12;
+			break;
+		default:
+			return 1;
+	}
+
+	/* first, turn off all power */
+	MBX_CSR2 &= ~(CR2_VDDSEL | CR2_VPPSEL);
+
+	/* enable new powersettings */
+	MBX_CSR2 |= reg;
+	debug ("MBX_CSR2 read = 0x%02x\n", MBX_CSR2);
+
+	return (0);
+}
+
+int pcmcia_hardware_enable (int slot)
+{
+	volatile immap_t *immap;
+	volatile cpm8xx_t *cp;
+	volatile pcmconf8xx_t *pcmp;
+	volatile sysconf8xx_t *sysp;
+	uint reg, mask;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n",
+	       'A' + slot);
+
+	udelay (10000);
+
+	immap = (immap_t *) CFG_IMMR;
+	sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
+	pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
+	cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;	/* active low  */
+	PCMCIA_PGCRX (_slot_) = reg;
+	udelay (500);
+
+	/* remove all power */
+	pcmcia_voltage_set (slot, 0, 0);
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+#ifndef CONFIG_HMI10
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+#else
+	if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
+#endif	/* CONFIG_HMI10 */
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On.
+	*/
+	mask = PCMCIA_VS1 (_slot_) | PCMCIA_VS2 (_slot_);
+	reg = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg,
+	       (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
+	       (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
+
+	if ((reg & mask) == mask) {
+		pcmcia_voltage_set (_slot_, 50, 0);
+		printf (" 5.0V card found: ");
+	} else {
+		pcmcia_voltage_set (_slot_, 33, 0);
+		printf (" 3.3V card found: ");
+	}
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg = PCMCIA_PGCRX (_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;	/* active low  */
+	PCMCIA_PGCRX (_slot_) = reg;
+
+	udelay (250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+	}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable (int slot)
+{
+	return 0;	/* No hardware to disable */
+}
+#endif /* CFG_CMD_PCMCIA */
+
+#endif	/* CONFIG_PCMCIA */
diff --git a/board/netta/Makefile b/board/netta/Makefile
index 68e24027a4..ee200c2d2d 100644
--- a/board/netta/Makefile
+++ b/board/netta/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o dsp.o codec.o
+OBJS	= $(BOARD).o flash.o dsp.o codec.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/netta/pcmcia.c b/board/netta/pcmcia.c
new file mode 100644
index 0000000000..a3709f7f77
--- /dev/null
+++ b/board/netta/pcmcia.c
@@ -0,0 +1,370 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+/* some sane bit macros */
+#define _BD(_b)				(1U << (31-(_b)))
+#define _BDR(_l, _h)			(((((1U << (31-(_l))) - 1) << 1) | 1) & ~((1U << (31-(_h))) - 1))
+
+#define _BW(_b)				(1U << (15-(_b)))
+#define _BWR(_l, _h)			(((((1U << (15-(_l))) - 1) << 1) | 1) & ~((1U << (15-(_h))) - 1))
+
+#define _BB(_b)				(1U << (7-(_b)))
+#define _BBR(_l, _h)			(((((1U << (7-(_l))) - 1) << 1) | 1) & ~((1U << (7-(_h))) - 1))
+
+#define _B(_b)				_BD(_b)
+#define _BR(_l, _h)			_BDR(_l, _h)
+
+#define PCMCIA_BOARD_MSG "NETTA"
+
+static const unsigned short vppd_masks[2] = { _BW(14), _BW(15) };
+
+static void cfg_vppd(int no)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask;
+
+	if ((unsigned int)no >= sizeof(vppd_masks)/sizeof(vppd_masks[0]))
+		return;
+
+	mask = vppd_masks[no];
+
+	immap->im_ioport.iop_papar &= ~mask;
+	immap->im_ioport.iop_paodr &= ~mask;
+	immap->im_ioport.iop_padir |=  mask;
+}
+
+static void set_vppd(int no, int what)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask;
+
+	if ((unsigned int)no >= sizeof(vppd_masks)/sizeof(vppd_masks[0]))
+		return;
+
+	mask = vppd_masks[no];
+
+	if (what)
+		immap->im_ioport.iop_padat |= mask;
+	else
+		immap->im_ioport.iop_padat &= ~mask;
+}
+
+static const unsigned short vccd_masks[2] = { _BW(10), _BW(6) };
+
+static void cfg_vccd(int no)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask;
+
+	if ((unsigned int)no >= sizeof(vccd_masks)/sizeof(vccd_masks[0]))
+		return;
+
+	mask = vccd_masks[no];
+
+	immap->im_ioport.iop_papar &= ~mask;
+	immap->im_ioport.iop_paodr &= ~mask;
+	immap->im_ioport.iop_padir |=  mask;
+}
+
+static void set_vccd(int no, int what)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask;
+
+	if ((unsigned int)no >= sizeof(vccd_masks)/sizeof(vccd_masks[0]))
+		return;
+
+	mask = vccd_masks[no];
+
+	if (what)
+		immap->im_ioport.iop_padat |= mask;
+	else
+		immap->im_ioport.iop_padat &= ~mask;
+}
+
+static const unsigned short oc_mask = _BW(8);
+
+static void cfg_oc(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask = oc_mask;
+
+	immap->im_ioport.iop_pcdir &= ~mask;
+	immap->im_ioport.iop_pcso  &= ~mask;
+	immap->im_ioport.iop_pcint &= ~mask;
+	immap->im_ioport.iop_pcpar &= ~mask;
+}
+
+static int get_oc(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask = oc_mask;
+	int what;
+
+	what = !!(immap->im_ioport.iop_pcdat & mask);;
+	return what;
+}
+
+static const unsigned short shdn_mask = _BW(12);
+
+static void cfg_shdn(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask;
+
+	mask = shdn_mask;
+
+	immap->im_ioport.iop_papar &= ~mask;
+	immap->im_ioport.iop_paodr &= ~mask;
+	immap->im_ioport.iop_padir |=  mask;
+}
+
+static void set_shdn(int what)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask;
+
+	mask = shdn_mask;
+
+	if (what)
+		immap->im_ioport.iop_padat |= mask;
+	else
+		immap->im_ioport.iop_padat &= ~mask;
+}
+
+static void cfg_ports (void)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+
+	cfg_vppd(0); cfg_vppd(1);	/* VPPD0,VPPD1 VAVPP => Hi-Z */
+	cfg_vccd(0); cfg_vccd(1);	/* 3V and 5V off */
+	cfg_shdn();
+	cfg_oc();
+
+	/*
+	* Configure Port A for TPS2211 PC-Card Power-Interface Switch
+	*
+	* Switch off all voltages, assert shutdown
+	*/
+	set_vppd(0, 1); set_vppd(1, 1);
+	set_vccd(0, 0); set_vccd(1, 0);
+	set_shdn(1);
+
+	udelay(100000);
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, pipr, mask;
+	int i;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
+	cfg_ports ();
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(500);
+
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
+	*/
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	pipr = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       pipr,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+
+	if ((pipr & mask) == mask) {
+		set_vppd(0, 1); set_vppd(1, 1); 		/* VAVPP => Hi-Z */
+		set_vccd(0, 0); set_vccd(1, 1); 		/* 5V on, 3V off */
+		puts (" 5.0V card found: ");
+	} else {
+		set_vppd(0, 1); set_vppd(1, 1); 		/* VAVPP => Hi-Z */
+		set_vccd(0, 1); set_vccd(1, 0); 		/* 5V off, 3V on */
+		puts (" 3.3V card found: ");
+	}
+
+	/*  Wait 500 ms; use this to check for over-current */
+	for (i=0; i<5000; ++i) {
+		if (!get_oc()) {
+			printf ("   *** Overcurrent - Safety shutdown ***\n");
+			set_vccd(0, 0); set_vccd(1, 0); 		/* VAVPP => Hi-Z */
+			return (1);
+		}
+		udelay (100);
+	}
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	/* All voltages off / Hi-Z */
+	set_vppd(0, 1); set_vppd(1, 1);
+	set_vccd(0, 1); set_vccd(1, 1);
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+	ushort sreg;
+
+	debug ("voltage_set: "
+			PCMCIA_BOARD_MSG
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Configure Port C pins for
+	* 5 Volts Enable and 3 Volts enable,
+	* Turn all power pins to Hi-Z
+	*/
+	debug ("PCMCIA power OFF\n");
+	cfg_ports ();	/* Enables switch, but all in Hi-Z */
+
+	sreg  = immap->im_ioport.iop_pcdat;
+	set_vppd(0, 1); set_vppd(1, 1);
+
+	switch(vcc) {
+		case  0:
+			break;	/* Switch off		*/
+
+		case 33:
+			set_vccd(0, 1); set_vccd(1, 0);
+			break;
+
+		case 50:
+			set_vccd(0, 0); set_vccd(1, 1);
+			break;
+
+		default:
+			goto done;
+	}
+
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+	       pcmp->pcmc_pipr,
+	       (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+done:
+			debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */
diff --git a/board/r360mpi/Makefile b/board/r360mpi/Makefile
index 13ce9fc9d2..1a7e7a693a 100644
--- a/board/r360mpi/Makefile
+++ b/board/r360mpi/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o
+OBJS	= $(BOARD).o flash.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/r360mpi/pcmcia.c b/board/r360mpi/pcmcia.c
new file mode 100644
index 0000000000..7d34ac80ae
--- /dev/null
+++ b/board/r360mpi/pcmcia.c
@@ -0,0 +1,236 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "R360MPI"
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, mask;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	* Configure SIUMCR to enable PCMCIA port B
+	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	*/
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Configure Ports A, B & C pins for
+	* 5 Volts Enable and 3 Volts enable
+	*/
+	immap->im_ioport.iop_pcpar &= ~(0x0400);
+	immap->im_ioport.iop_pcso  &= ~(0x0400);/*
+	immap->im_ioport.iop_pcdir |= 0x0400;*/
+
+	immap->im_ioport.iop_papar &= ~(0x0200);/*
+	immap->im_ioport.iop_padir |= 0x0200;*/
+#if 0
+	immap->im_ioport.iop_pbpar &= ~(0xC000);
+	immap->im_ioport.iop_pbdir &= ~(0xC000);
+#endif
+	/* remove all power */
+
+	immap->im_ioport.iop_pcdat |= 0x0400;
+	immap->im_ioport.iop_padat |= 0x0200;
+
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On.
+	*/
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	reg  = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       reg,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+	if ((reg & mask) == mask) {
+		immap->im_ioport.iop_pcdat &= ~(0x4000);
+		puts (" 5.0V card found: ");
+	} else {
+		immap->im_ioport.iop_padat &= ~(0x0002);
+		puts (" 3.3V card found: ");
+	}
+	immap->im_ioport.iop_pcdir |= 0x0400;
+	immap->im_ioport.iop_padir |= 0x0200;
+#if 0
+	/*  VCC switch error flag, PCMCIA slot INPACK_ pin */
+	cp->cp_pbdir &= ~(0x0020 | 0x0010);
+	cp->cp_pbpar &= ~(0x0020 | 0x0010);
+	udelay(500000);
+#endif
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+	/* remove all power */
+	immap->im_ioport.iop_pcdat |= 0x0400;
+	immap->im_ioport.iop_padat |= 0x0200;
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("voltage_set: "
+			PCMCIA_BOARD_MSG
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Configure Ports A & C pins for
+	* 5 Volts Enable and 3 Volts enable,
+	* Turn off all power
+	*/
+	debug ("PCMCIA power OFF\n");
+	immap->im_ioport.iop_pcpar &= ~(0x0400);
+	immap->im_ioport.iop_pcso  &= ~(0x0400);/*
+	immap->im_ioport.iop_pcdir |= 0x0400;*/
+
+	immap->im_ioport.iop_papar &= ~(0x0200);/*
+	immap->im_ioport.iop_padir |= 0x0200;*/
+
+	immap->im_ioport.iop_pcdat |= 0x0400;
+	immap->im_ioport.iop_padat |= 0x0200;
+
+	reg = 0;
+	switch(vcc) {
+		case  0: 		break;
+		case 33: reg |= 0x0200;	break;
+		case 50: reg |= 0x0400;	break;
+		default: 		goto done;
+	}
+
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+	       pcmp->pcmc_pipr,
+	       (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+	if (reg & 0x0200)
+		immap->im_ioport.iop_pcdat &= !reg;
+	if (reg & 0x0400)
+		immap->im_ioport.iop_padat &= !reg;
+	immap->im_ioport.iop_pcdir |= 0x0200;
+	immap->im_ioport.iop_padir |= 0x0400;
+	if (reg) {
+		debug ("PCMCIA powered at %sV\n",
+		       (reg&0x0400) ? "5.0" : "3.3");
+	} else {
+		debug ("PCMCIA powered down\n");
+	}
+
+done:
+			debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CCONFIG_PCMCIA */
diff --git a/board/uc100/Makefile b/board/uc100/Makefile
index eb81625fef..2d2cc23209 100644
--- a/board/uc100/Makefile
+++ b/board/uc100/Makefile
@@ -25,8 +25,8 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-#OBJS	= $(BOARD).o flash.o
-OBJS	= $(BOARD).o
+#OBJS	= $(BOARD).o flash.o pcmcia.o
+OBJS	= $(BOARD).o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/uc100/pcmcia.c b/board/uc100/pcmcia.c
new file mode 100644
index 0000000000..6e4b6d6c66
--- /dev/null
+++ b/board/uc100/pcmcia.c
@@ -0,0 +1,198 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "UC100"
+
+/*
+ * Remark: don't turn off OE "__MY_PCMCIA_GCRX_CXOE" on UC100 board.
+ *         This leads to board-hangup! (sr, 8 Dez. 2004)
+ */
+static void cfg_ports (void)
+{
+	volatile immap_t	*immap;
+
+	immap = (immap_t *)CFG_IMMR;
+
+	/*
+	* Configure Port A for MAX1602 PC-Card Power-Interface Switch
+	*/
+	immap->im_ioport.iop_padat &= ~0x8000;	/* set port x output to low */
+	immap->im_ioport.iop_padir |= 0x8000;	/* enable port x as output */
+
+	debug ("Set Port A: PAR: %08x DIR: %08x DAT: %08x\n",
+	       immap->im_ioport.iop_papar, immap->im_ioport.iop_padir,
+	       immap->im_ioport.iop_padat);
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, mask;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
+	cfg_ports ();
+
+	/*
+	* Configure SIUMCR to enable PCMCIA port B
+	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	*/
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On.
+	*/
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	reg  = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       reg,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+	if ((reg & mask) == mask) {
+		puts (" 5.0V card found: ");
+	} else {
+		puts (" 3.3V card found: ");
+	}
+
+	/*  switch VCC on */
+	immap->im_ioport.iop_padat |= 0x8000; /* power enable 3.3V */
+
+	udelay(10000);
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+	/* switch VCC off */
+	immap->im_ioport.iop_padat &= ~0x8000; /* power disable 3.3V */
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("voltage_set: "
+			PCMCIA_BOARD_MSG
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Configure Port C pins for
+	* 5 Volts Enable and 3 Volts enable,
+	* Turn all power pins to Hi-Z
+	*/
+	debug ("PCMCIA power OFF\n");
+	cfg_ports ();	/* Enables switch, but all in Hi-Z */
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */