dts: update to v4.20-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

9 files changed, 194 insertions, 3 deletions

diff --git a/dts/Bindings/mmc/arasan,sdhci.txt b/dts/Bindings/mmc/arasan,sdhci.txt
index f6ddba31cb..e2effe17f0 100644
--- a/dts/Bindings/mmc/arasan,sdhci.txt
+++ b/dts/Bindings/mmc/arasan,sdhci.txt
@@ -15,6 +15,7 @@ Required Properties:
     - "arasan,sdhci-5.1": generic Arasan SDHCI 5.1 PHY
     - "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1": rk3399 eMMC PHY
       For this device it is strongly suggested to include arasan,soc-ctl-syscon.
+    - "ti,am654-sdhci-5.1", "arasan,sdhci-5.1": TI AM654 MMC PHY
   - reg: From mmc bindings: Register location and length.
   - clocks: From clock bindings: Handles to clock inputs.
   - clock-names: From clock bindings: Tuple including "clk_xin" and "clk_ahb"
diff --git a/dts/Bindings/mmc/jz4740.txt b/dts/Bindings/mmc/jz4740.txt
index 7cd8c432d7..8a6f87f131 100644
--- a/dts/Bindings/mmc/jz4740.txt
+++ b/dts/Bindings/mmc/jz4740.txt
@@ -7,6 +7,7 @@ described in mmc.txt.
 Required properties:
 - compatible: Should be one of the following:
   - "ingenic,jz4740-mmc" for the JZ4740
+  - "ingenic,jz4725b-mmc" for the JZ4725B
   - "ingenic,jz4780-mmc" for the JZ4780
 - reg: Should contain the MMC controller registers location and length.
 - interrupts: Should contain the interrupt specifier of the MMC controller.
diff --git a/dts/Bindings/mmc/mmci.txt b/dts/Bindings/mmc/mmci.txt
index 03796cf2d3..6d3c626e01 100644
--- a/dts/Bindings/mmc/mmci.txt
+++ b/dts/Bindings/mmc/mmci.txt
@@ -15,8 +15,11 @@ Required properties:
 Optional properties:
 - arm,primecell-periphid : contains the PrimeCell Peripheral ID, it overrides
                            the ID provided by the HW
+- resets                 : phandle to internal reset line.
+			   Should be defined for sdmmc variant.
 - vqmmc-supply           : phandle to the regulator device tree node, mentioned
                            as the VCCQ/VDD_IO supply in the eMMC/SD specs.
+specific for ux500 variant:
 - st,sig-dir-dat0        : bus signal direction pin used for DAT[0].
 - st,sig-dir-dat2        : bus signal direction pin used for DAT[2].
 - st,sig-dir-dat31       : bus signal direction pin used for DAT[3] and DAT[1].
@@ -24,6 +27,14 @@ Optional properties:
 - st,sig-dir-cmd         : cmd signal direction pin used for CMD.
 - st,sig-pin-fbclk       : feedback clock signal pin used.
 
+specific for sdmmc variant:
+- st,sig-dir             : signal direction polarity used for cmd, dat0 dat123.
+- st,neg-edge            : data & command phase relation, generated on
+                           sd clock falling edge.
+- st,use-ckin            : use ckin pin from an external driver to sample
+                           the receive data (example: with voltage
+			   switch transceiver).
+
 Deprecated properties:
 - mmc-cap-mmc-highspeed  : indicates whether MMC is high speed capable.
 - mmc-cap-sd-highspeed   : indicates whether SD is high speed capable.
diff --git a/dts/Bindings/mmc/mtk-sd.txt b/dts/Bindings/mmc/mtk-sd.txt
index f33467a54a..f5bcda3980 100644
--- a/dts/Bindings/mmc/mtk-sd.txt
+++ b/dts/Bindings/mmc/mtk-sd.txt
@@ -10,6 +10,7 @@ Required properties:
 - compatible: value should be either of the following.
 	"mediatek,mt8135-mmc": for mmc host ip compatible with mt8135
 	"mediatek,mt8173-mmc": for mmc host ip compatible with mt8173
+	"mediatek,mt8183-mmc": for mmc host ip compatible with mt8183
 	"mediatek,mt2701-mmc": for mmc host ip compatible with mt2701
 	"mediatek,mt2712-mmc": for mmc host ip compatible with mt2712
 	"mediatek,mt7622-mmc": for MT7622 SoC
@@ -22,6 +23,7 @@ Required properties:
 	"source" - source clock (required)
 	"hclk" - HCLK which used for host (required)
 	"source_cg" - independent source clock gate (required for MT2712)
+	"bus_clk" - bus clock used for internal register access (required for MT2712 MSDC0/3)
 - pinctrl-names: should be "default", "state_uhs"
 - pinctrl-0: should contain default/high speed pin ctrl
 - pinctrl-1: should contain uhs mode pin ctrl
diff --git a/dts/Bindings/mmc/nvidia,tegra20-sdhci.txt b/dts/Bindings/mmc/nvidia,tegra20-sdhci.txt
index 9bce57862e..32b4b4e419 100644
--- a/dts/Bindings/mmc/nvidia,tegra20-sdhci.txt
+++ b/dts/Bindings/mmc/nvidia,tegra20-sdhci.txt
@@ -38,3 +38,75 @@ sdhci@c8000200 {
 	power-gpios = <&gpio 155 0>; /* gpio PT3 */
 	bus-width = <8>;
 };
+
+Optional properties for Tegra210 and Tegra186:
+- pinctrl-names, pinctrl-0, pinctrl-1 : Specify pad voltage
+  configurations. Valid pinctrl-names are "sdmmc-3v3" and "sdmmc-1v8"
+  for controllers supporting multiple voltage levels. The order of names
+  should correspond to the pin configuration states in pinctrl-0 and
+  pinctrl-1.
+- nvidia,only-1-8-v : The presence of this property indicates that the
+  controller operates at a 1.8 V fixed I/O voltage.
+- nvidia,pad-autocal-pull-up-offset-3v3,
+  nvidia,pad-autocal-pull-down-offset-3v3 : Specify drive strength
+  calibration offsets for 3.3 V signaling modes.
+- nvidia,pad-autocal-pull-up-offset-1v8,
+  nvidia,pad-autocal-pull-down-offset-1v8 : Specify drive strength
+  calibration offsets for 1.8 V signaling modes.
+- nvidia,pad-autocal-pull-up-offset-3v3-timeout,
+  nvidia,pad-autocal-pull-down-offset-3v3-timeout : Specify drive
+  strength used as a fallback in case the automatic calibration times
+  out on a 3.3 V signaling mode.
+- nvidia,pad-autocal-pull-up-offset-1v8-timeout,
+  nvidia,pad-autocal-pull-down-offset-1v8-timeout : Specify drive
+  strength used as a fallback in case the automatic calibration times
+  out on a 1.8 V signaling mode.
+- nvidia,pad-autocal-pull-up-offset-sdr104,
+  nvidia,pad-autocal-pull-down-offset-sdr104 : Specify drive strength
+  calibration offsets for SDR104 mode.
+- nvidia,pad-autocal-pull-up-offset-hs400,
+  nvidia,pad-autocal-pull-down-offset-hs400 : Specify drive strength
+  calibration offsets for HS400 mode.
+- nvidia,default-tap : Specify the default inbound sampling clock
+  trimmer value for non-tunable modes.
+- nvidia,default-trim : Specify the default outbound clock trimmer
+  value.
+- nvidia,dqs-trim : Specify DQS trim value for HS400 timing
+
+  Notes on the pad calibration pull up and pulldown offset values:
+    - The property values are drive codes which are programmed into the
+      PD_OFFSET and PU_OFFSET sections of the
+      SDHCI_TEGRA_AUTO_CAL_CONFIG register.
+    - A higher value corresponds to higher drive strength. Please refer
+      to the reference manual of the SoC for correct values.
+    - The SDR104 and HS400 timing specific values are used in
+      corresponding modes if specified.
+
+  Notes on tap and trim values:
+    - The values are used for compensating trace length differences
+      by adjusting the sampling point.
+    - The values are programmed to the Vendor Clock Control Register.
+      Please refer to the reference manual of the SoC for correct
+      values.
+    - The DQS trim values are only used on controllers which support
+      HS400 timing. Only SDMMC4 on Tegra210 and Tegra 186 supports
+      HS400.
+
+Example:
+sdhci@700b0000 {
+	compatible = "nvidia,tegra210-sdhci", "nvidia,tegra124-sdhci";
+	reg = <0x0 0x700b0000 0x0 0x200>;
+	interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&tegra_car TEGRA210_CLK_SDMMC1>;
+	clock-names = "sdhci";
+	resets = <&tegra_car 14>;
+	reset-names = "sdhci";
+	pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+	pinctrl-0 = <&sdmmc1_3v3>;
+	pinctrl-1 = <&sdmmc1_1v8>;
+	nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>;
+	nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>;
+	nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>;
+	nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>;
+	status = "disabled";
+};
diff --git a/dts/Bindings/mmc/renesas,mmcif.txt b/dts/Bindings/mmc/renesas,mmcif.txt
index 5ff1e12c65..c064af5838 100644
--- a/dts/Bindings/mmc/renesas,mmcif.txt
+++ b/dts/Bindings/mmc/renesas,mmcif.txt
@@ -12,6 +12,7 @@ Required properties:
 	- "renesas,mmcif-r8a73a4" for the MMCIF found in r8a73a4 SoCs
 	- "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs
 	- "renesas,mmcif-r8a7743" for the MMCIF found in r8a7743 SoCs
+	- "renesas,mmcif-r8a7744" for the MMCIF found in r8a7744 SoCs
 	- "renesas,mmcif-r8a7745" for the MMCIF found in r8a7745 SoCs
 	- "renesas,mmcif-r8a7778" for the MMCIF found in r8a7778 SoCs
 	- "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs
@@ -23,7 +24,8 @@ Required properties:
 - interrupts: Some SoCs have only 1 shared interrupt, while others have either
   2 or 3 individual interrupts (error, int, card detect). Below is the number
   of interrupts for each SoC:
-    1: r8a73a4, r8a7743, r8a7745, r8a7778, r8a7790, r8a7791, r8a7793, r8a7794
+    1: r8a73a4, r8a7743, r8a7744, r8a7745, r8a7778, r8a7790, r8a7791, r8a7793,
+       r8a7794
     2: r8a7740, sh73a0
     3: r7s72100
 
diff --git a/dts/Bindings/mmc/sdhci-sprd.txt b/dts/Bindings/mmc/sdhci-sprd.txt
new file mode 100644
index 0000000000..45c9978aad
--- /dev/null
+++ b/dts/Bindings/mmc/sdhci-sprd.txt
@@ -0,0 +1,41 @@
+* Spreadtrum SDHCI controller (sdhci-sprd)
+
+The Secure Digital (SD) Host controller on Spreadtrum SoCs provides an interface
+for MMC, SD and SDIO types of cards.
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the sdhci-sprd driver.
+
+Required properties:
+- compatible: Should contain "sprd,sdhci-r11".
+- reg: physical base address of the controller and length.
+- interrupts: Interrupts used by the SDHCI controller.
+- clocks: Should contain phandle for the clock feeding the SDHCI controller
+- clock-names: Should contain the following:
+	"sdio" - SDIO source clock (required)
+	"enable" - gate clock which used for enabling/disabling the device (required)
+
+Optional properties:
+- assigned-clocks: the same with "sdio" clock
+- assigned-clock-parents: the default parent of "sdio" clock
+
+Examples:
+
+sdio0: sdio@20600000 {
+	compatible  = "sprd,sdhci-r11";
+	reg = <0 0x20600000 0 0x1000>;
+	interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+
+	clock-names = "sdio", "enable";
+	clocks = <&ap_clk CLK_EMMC_2X>,
+		 <&apahb_gate CLK_EMMC_EB>;
+	assigned-clocks = <&ap_clk CLK_EMMC_2X>;
+	assigned-clock-parents = <&rpll CLK_RPLL_390M>;
+
+	bus-width = <8>;
+	non-removable;
+	no-sdio;
+	no-sd;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
diff --git a/dts/Bindings/mmc/tmio_mmc.txt b/dts/Bindings/mmc/tmio_mmc.txt
index c434200d19..27f2eab298 100644
--- a/dts/Bindings/mmc/tmio_mmc.txt
+++ b/dts/Bindings/mmc/tmio_mmc.txt
@@ -16,7 +16,11 @@ Required properties:
 		"renesas,sdhi-r8a73a4" - SDHI IP on R8A73A4 SoC
 		"renesas,sdhi-r8a7740" - SDHI IP on R8A7740 SoC
 		"renesas,sdhi-r8a7743" - SDHI IP on R8A7743 SoC
+		"renesas,sdhi-r8a7744" - SDHI IP on R8A7744 SoC
 		"renesas,sdhi-r8a7745" - SDHI IP on R8A7745 SoC
+		"renesas,sdhi-r8a774a1" - SDHI IP on R8A774A1 SoC
+		"renesas,sdhi-r8a77470" - SDHI IP on R8A77470 SoC
+		"renesas,sdhi-mmc-r8a77470" - SDHI/MMC IP on R8A77470 SoC
 		"renesas,sdhi-r8a7778" - SDHI IP on R8A7778 SoC
 		"renesas,sdhi-r8a7779" - SDHI IP on R8A7779 SoC
 		"renesas,sdhi-r8a7790" - SDHI IP on R8A7790 SoC
@@ -27,14 +31,16 @@ Required properties:
 		"renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC
 		"renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC
 		"renesas,sdhi-r8a77965" - SDHI IP on R8A77965 SoC
+		"renesas,sdhi-r8a77970" - SDHI IP on R8A77970 SoC
 		"renesas,sdhi-r8a77980" - SDHI IP on R8A77980 SoC
 		"renesas,sdhi-r8a77990" - SDHI IP on R8A77990 SoC
 		"renesas,sdhi-r8a77995" - SDHI IP on R8A77995 SoC
 		"renesas,sdhi-shmobile" - a generic sh-mobile SDHI controller
 		"renesas,rcar-gen1-sdhi" - a generic R-Car Gen1 SDHI controller
-		"renesas,rcar-gen2-sdhi" - a generic R-Car Gen2 or RZ/G1
+		"renesas,rcar-gen2-sdhi" - a generic R-Car Gen2 and RZ/G1 SDHI
+					   (not SDHI/MMC) controller
+		"renesas,rcar-gen3-sdhi" - a generic R-Car Gen3 or RZ/G2
 					   SDHI controller
-		"renesas,rcar-gen3-sdhi" - a generic R-Car Gen3 SDHI controller
 
 
 		When compatible with the generic version, nodes must list
diff --git a/dts/Bindings/mmc/uniphier-sd.txt b/dts/Bindings/mmc/uniphier-sd.txt
new file mode 100644
index 0000000000..e1d6587557
--- /dev/null
+++ b/dts/Bindings/mmc/uniphier-sd.txt
@@ -0,0 +1,55 @@
+UniPhier SD/eMMC controller
+
+Required properties:
+- compatible: should be one of the following:
+    "socionext,uniphier-sd-v2.91"  - IP version 2.91
+    "socionext,uniphier-sd-v3.1"   - IP version 3.1
+    "socionext,uniphier-sd-v3.1.1" - IP version 3.1.1
+- reg: offset and length of the register set for the device.
+- interrupts: a single interrupt specifier.
+- clocks: a single clock specifier of the controller clock.
+- reset-names: should contain the following:
+    "host"   - mandatory for all versions
+    "bridge" - should exist only for "socionext,uniphier-sd-v2.91"
+    "hw"     - should exist if eMMC hw reset line is available
+- resets: a list of reset specifiers, corresponding to the reset-names
+
+Optional properties:
+- pinctrl-names: if present, should contain the following:
+    "default" - should exist for all instances
+    "uhs"     - should exist for SD instance with UHS support
+- pinctrl-0: pin control state for the default mode
+- pinctrl-1: pin control state for the UHS mode
+- dma-names: should be "rx-tx" if present.
+  This property can exist only for "socionext,uniphier-sd-v2.91".
+- dmas: a single DMA channel specifier
+  This property can exist only for "socionext,uniphier-sd-v2.91".
+- bus-width: see mmc.txt
+- cap-sd-highspeed: see mmc.txt
+- cap-mmc-highspeed: see mmc.txt
+- sd-uhs-sdr12: see mmc.txt
+- sd-uhs-sdr25: see mmc.txt
+- sd-uhs-sdr50: see mmc.txt
+- cap-mmc-hw-reset: should exist if reset-names contains "hw". see mmc.txt
+- non-removable: see mmc.txt
+
+Example:
+
+	sd: sdhc@5a400000 {
+		compatible = "socionext,uniphier-sd-v2.91";
+		reg = <0x5a400000 0x200>;
+		interrupts = <0 76 4>;
+		pinctrl-names = "default", "uhs";
+		pinctrl-0 = <&pinctrl_sd>;
+		pinctrl-1 = <&pinctrl_sd_uhs>;
+		clocks = <&mio_clk 0>;
+		reset-names = "host", "bridge";
+		resets = <&mio_rst 0>, <&mio_rst 3>;
+		dma-names = "rx-tx";
+		dmas = <&dmac 4>;
+		bus-width = <4>;
+		cap-sd-highspeed;
+		sd-uhs-sdr12;
+		sd-uhs-sdr25;
+		sd-uhs-sdr50;
+	};