dts: update to v5.2-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

11 files changed, 389 insertions, 149 deletions

diff --git a/dts/Bindings/mtd/allwinner,sun4i-a10-nand.yaml b/dts/Bindings/mtd/allwinner,sun4i-a10-nand.yaml
new file mode 100644
index 0000000000..fbd4da3684
--- /dev/null
+++ b/dts/Bindings/mtd/allwinner,sun4i-a10-nand.yaml
@@ -0,0 +1,97 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/allwinner,sun4i-a10-nand.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A10 NAND Controller Device Tree Bindings
+
+allOf:
+  - $ref: "nand-controller.yaml"
+
+maintainers:
+  - Chen-Yu Tsai <wens@csie.org>
+  - Maxime Ripard <maxime.ripard@bootlin.com>
+
+properties:
+  "#address-cells": true
+  "#size-cells": true
+
+  compatible:
+    enum:
+      - allwinner,sun4i-a10-nand
+      - allwinner,sun8i-a23-nand-controller
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Bus Clock
+      - description: Module Clock
+
+  clock-names:
+    items:
+      - const: ahb
+      - const: mod
+
+  resets:
+    maxItems: 1
+
+  reset-names:
+    const: ahb
+
+  dmas:
+    maxItems: 1
+
+  dma-names:
+    const: rxtx
+
+  pinctrl-names: true
+
+patternProperties:
+  "^pinctrl-[0-9]+$": true
+
+  "^nand@[a-f0-9]+$":
+    properties:
+      reg:
+        maxItems: 1
+        minimum: 0
+        maximum: 7
+
+      nand-ecc-mode: true
+
+      nand-ecc-algo:
+        const: bch
+
+      nand-ecc-step-size:
+        enum: [ 512, 1024 ]
+
+      nand-ecc-strength:
+        maximum: 80
+
+      allwinner,rb:
+        description:
+          Contains the native Ready/Busy IDs.
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/uint32-array
+          - minItems: 1
+            maxItems: 2
+            items:
+              minimum: 0
+              maximum: 1
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+...
diff --git a/dts/Bindings/mtd/atmel-nand.txt b/dts/Bindings/mtd/atmel-nand.txt
index 9bb66e4766..68b51dc588 100644
--- a/dts/Bindings/mtd/atmel-nand.txt
+++ b/dts/Bindings/mtd/atmel-nand.txt
@@ -14,6 +14,7 @@ Required properties:
 	"atmel,at91sam9261-nand-controller"
 	"atmel,at91sam9g45-nand-controller"
 	"atmel,sama5d3-nand-controller"
+	"microchip,sam9x60-nand-controller"
 - ranges: empty ranges property to forward EBI ranges definitions.
 - #address-cells: should be set to 2.
 - #size-cells: should be set to 1.
diff --git a/dts/Bindings/mtd/denali-nand.txt b/dts/Bindings/mtd/denali-nand.txt
index f33da87827..b14b6751c2 100644
--- a/dts/Bindings/mtd/denali-nand.txt
+++ b/dts/Bindings/mtd/denali-nand.txt
@@ -7,34 +7,48 @@ Required properties:
       "socionext,uniphier-denali-nand-v5b"  - for Socionext UniPhier (v5b)
   - reg : should contain registers location and length for data and reg.
   - reg-names: Should contain the reg names "nand_data" and "denali_reg"
+  - #address-cells: should be 1. The cell encodes the chip select connection.
+  - #size-cells : should be 0.
   - interrupts : The interrupt number.
   - clocks: should contain phandle of the controller core clock, the bus
     interface clock, and the ECC circuit clock.
   - clock-names: should contain "nand", "nand_x", "ecc"
 
-Optional properties:
-  - nand-ecc-step-size: see nand.txt for details.  If present, the value must be
-      512        for "altr,socfpga-denali-nand"
-      1024       for "socionext,uniphier-denali-nand-v5a"
-      1024       for "socionext,uniphier-denali-nand-v5b"
-  - nand-ecc-strength: see nand.txt for details.  Valid values are:
-      8, 15      for "altr,socfpga-denali-nand"
-      8, 16, 24  for "socionext,uniphier-denali-nand-v5a"
-      8, 16      for "socionext,uniphier-denali-nand-v5b"
-  - nand-ecc-maximize: see nand.txt for details
-
-The device tree may optionally contain sub-nodes describing partitions of the
+Sub-nodes:
+  Sub-nodes represent available NAND chips.
+
+  Required properties:
+    - reg: should contain the bank ID of the controller to which each chip
+      select is connected.
+
+  Optional properties:
+    - nand-ecc-step-size: see nand.txt for details.
+      If present, the value must be
+        512        for "altr,socfpga-denali-nand"
+        1024       for "socionext,uniphier-denali-nand-v5a"
+        1024       for "socionext,uniphier-denali-nand-v5b"
+    - nand-ecc-strength: see nand.txt for details. Valid values are:
+        8, 15      for "altr,socfpga-denali-nand"
+        8, 16, 24  for "socionext,uniphier-denali-nand-v5a"
+        8, 16      for "socionext,uniphier-denali-nand-v5b"
+    - nand-ecc-maximize: see nand.txt for details
+
+The chip nodes may optionally contain sub-nodes describing partitions of the
 address space. See partition.txt for more detail.
 
 Examples:
 
 nand: nand@ff900000 {
 	#address-cells = <1>;
-	#size-cells = <1>;
+	#size-cells = <0>;
 	compatible = "altr,socfpga-denali-nand";
 	reg = <0xff900000 0x20>, <0xffb80000 0x1000>;
 	reg-names = "nand_data", "denali_reg";
 	clocks = <&nand_clk>, <&nand_x_clk>, <&nand_ecc_clk>;
 	clock-names = "nand", "nand_x", "ecc";
 	interrupts = <0 144 4>;
+
+	nand@0 {
+		reg = <0>;
+	}
 };
diff --git a/dts/Bindings/mtd/ingenic,jz4780-nand.txt b/dts/Bindings/mtd/ingenic,jz4780-nand.txt
index 29ea5853ca..c022593533 100644
--- a/dts/Bindings/mtd/ingenic,jz4780-nand.txt
+++ b/dts/Bindings/mtd/ingenic,jz4780-nand.txt
@@ -1,4 +1,4 @@
-* Ingenic JZ4780 NAND/BCH
+* Ingenic JZ4780 NAND/ECC
 
 This file documents the device tree bindings for NAND flash devices on the
 JZ4780. NAND devices are connected to the NEMC controller (described in
@@ -6,15 +6,18 @@ memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must
 be children of the NEMC node.
 
 Required NAND controller device properties:
-- compatible: Should be set to "ingenic,jz4780-nand".
+- compatible: Should be one of:
+  * ingenic,jz4740-nand
+  * ingenic,jz4725b-nand
+  * ingenic,jz4780-nand
 - reg: For each bank with a NAND chip attached, should specify a bank number,
   an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank).
 
 Optional NAND controller device properties:
-- ingenic,bch-controller: To make use of the hardware BCH controller, this
-  property must contain a phandle for the BCH controller node. The required
+- ecc-engine: To make use of the hardware ECC controller, this
+  property must contain a phandle for the ECC controller node. The required
   properties for this node are described below. If this is not specified,
-  software BCH will be used instead.
+  software ECC will be used instead.
 
 Optional children nodes:
 - Individual NAND chips are children of the NAND controller node.
@@ -45,7 +48,7 @@ nemc: nemc@13410000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ingenic,bch-controller = <&bch>;
+		ecc-engine = <&bch>;
 
 		nand@1 {
 			reg = <1>;
@@ -67,14 +70,17 @@ nemc: nemc@13410000 {
 	};
 };
 
-The BCH controller is a separate SoC component used for error correction on
+The ECC controller is a separate SoC component used for error correction on
 NAND devices. The following is a description of the device properties for a
-BCH controller.
-
-Required BCH properties:
-- compatible: Should be set to "ingenic,jz4780-bch".
-- reg: Should specify the BCH controller registers location and length.
-- clocks: Clock for the BCH controller.
+ECC controller.
+
+Required ECC properties:
+- compatible: Should be one of:
+  * ingenic,jz4740-ecc
+  * ingenic,jz4725b-bch
+  * ingenic,jz4780-bch
+- reg: Should specify the ECC controller registers location and length.
+- clocks: Clock for the ECC controller.
 
 Example:
 
diff --git a/dts/Bindings/mtd/mtd-physmap.txt b/dts/Bindings/mtd/mtd-physmap.txt
index 7df0dcaccb..c69f4f065d 100644
--- a/dts/Bindings/mtd/mtd-physmap.txt
+++ b/dts/Bindings/mtd/mtd-physmap.txt
@@ -96,3 +96,19 @@ An example using SRAM:
 		bank-width = <2>;
 	};
 
+An example using gpio-addrs
+
+	flash@20000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "cfi-flash", "jedec-flash";
+		reg = <0x20000000 0x02000000>;
+		ranges = <0 0x00000000 0x02000000
+		          1 0x02000000 0x02000000>;
+		bank-width = <2>;
+		addr-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		partition@0 {
+			label = "test-part1";
+			reg = <0 0x04000000>;
+		};
+	};
diff --git a/dts/Bindings/mtd/nand-controller.yaml b/dts/Bindings/mtd/nand-controller.yaml
new file mode 100644
index 0000000000..199ba5ac2a
--- /dev/null
+++ b/dts/Bindings/mtd/nand-controller.yaml
@@ -0,0 +1,143 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/nand-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NAND Chip and NAND Controller Generic Binding
+
+maintainers:
+  - Miquel Raynal <miquel.raynal@bootlin.com>
+  - Richard Weinberger <richard@nod.at>
+
+description: |
+  The NAND controller should be represented with its own DT node, and
+  all NAND chips attached to this controller should be defined as
+  children nodes of the NAND controller. This representation should be
+  enforced even for simple controllers supporting only one chip.
+
+  The ECC strength and ECC step size properties define the user
+  desires in terms of correction capability of a controller. Together,
+  they request the ECC engine to correct {strength} bit errors per
+  {size} bytes.
+
+  The interpretation of these parameters is implementation-defined, so
+  not all implementations must support all possible
+  combinations. However, implementations are encouraged to further
+  specify the value(s) they support.
+
+properties:
+  $nodename:
+    pattern: "^nand-controller(@.*)?"
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  ranges: true
+
+patternProperties:
+  "^nand@[a-f0-9]$":
+    properties:
+      reg:
+        description:
+          Contains the native Ready/Busy IDs.
+
+      nand-ecc-mode:
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/string
+          - enum: [ none, soft, hw, hw_syndrome, hw_oob_first, on-die ]
+        description:
+          Desired ECC engine, either hardware (most of the time
+          embedded in the NAND controller) or software correction
+          (Linux will handle the calculations). soft_bch is deprecated
+          and should be replaced by soft and nand-ecc-algo.
+
+      nand-ecc-algo:
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/string
+          - enum: [ hamming, bch, rs ]
+        description:
+          Desired ECC algorithm.
+
+      nand-bus-width:
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/uint32
+          - enum: [ 8, 16 ]
+          - default: 8
+        description:
+          Bus width to the NAND chip
+
+      nand-on-flash-bbt:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          With this property, the OS will search the device for a Bad
+          Block Table (BBT). If not found, it will create one, reserve
+          a few blocks at the end of the device to store it and update
+          it as the device ages. Otherwise, the out-of-band area of a
+          few pages of all the blocks will be scanned at boot time to
+          find Bad Block Markers (BBM). These markers will help to
+          build a volatile BBT in RAM.
+
+      nand-ecc-strength:
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/uint32
+          - minimum: 1
+        description:
+          Maximum number of bits that can be corrected per ECC step.
+
+      nand-ecc-step-size:
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/uint32
+          - minimum: 1
+        description:
+          Number of data bytes covered by a single ECC step.
+
+      nand-ecc-maximize:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Whether or not the ECC strength should be maximized. The
+          maximum ECC strength is both controller and chip
+          dependent. The ECC engine has to select the ECC config
+          providing the best strength and taking the OOB area size
+          constraint into account. This is particularly useful when
+          only the in-band area is used by the upper layers, and you
+          want to make your NAND as reliable as possible.
+
+      nand-is-boot-medium:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Whether or not the NAND chip is a boot medium. Drivers might
+          use this information to select ECC algorithms supported by
+          the boot ROM or similar restrictions.
+
+      nand-rb:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        description:
+          Contains the native Ready/Busy IDs.
+
+    required:
+      - reg
+
+required:
+  - "#address-cells"
+  - "#size-cells"
+
+examples:
+  - |
+    nand-controller {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      /* controller specific properties */
+
+      nand@0 {
+        reg = <0>;
+        nand-ecc-mode = "soft";
+        nand-ecc-algo = "bch";
+
+        /* controller specific properties */
+      };
+    };
diff --git a/dts/Bindings/mtd/nand.txt b/dts/Bindings/mtd/nand.txt
deleted file mode 100644
index e949c778e9..0000000000
--- a/dts/Bindings/mtd/nand.txt
+++ /dev/null
@@ -1,75 +0,0 @@
-* NAND chip and NAND controller generic binding
-
-NAND controller/NAND chip representation:
-
-The NAND controller should be represented with its own DT node, and all
-NAND chips attached to this controller should be defined as children nodes
-of the NAND controller. This representation should be enforced even for
-simple controllers supporting only one chip.
-
-Mandatory NAND controller properties:
-- #address-cells: depends on your controller. Should at least be 1 to
-		  encode the CS line id.
-- #size-cells: depends on your controller. Put zero unless you need a
-	       mapping between CS lines and dedicated memory regions
-
-Optional NAND controller properties
-- ranges: only needed if you need to define a mapping between CS lines and
-	  memory regions
-
-Optional NAND chip properties:
-
-- nand-ecc-mode : String, operation mode of the NAND ecc mode.
-		  Supported values are: "none", "soft", "hw", "hw_syndrome",
-		  "hw_oob_first", "on-die".
-		  Deprecated values:
-		  "soft_bch": use "soft" and nand-ecc-algo instead
-- nand-ecc-algo: string, algorithm of NAND ECC.
-		 Valid values are: "hamming", "bch", "rs".
-- nand-bus-width : 8 or 16 bus width if not present 8
-- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
-
-- nand-ecc-strength: integer representing the number of bits to correct
-		     per ECC step.
-
-- nand-ecc-step-size: integer representing the number of data bytes
-		      that are covered by a single ECC step.
-
-- nand-ecc-maximize: boolean used to specify that you want to maximize ECC
-		     strength. The maximum ECC strength is both controller and
-		     chip dependent. The controller side has to select the ECC
-		     config providing the best strength and taking the OOB area
-		     size constraint into account.
-		     This is particularly useful when only the in-band area is
-		     used by the upper layers, and you want to make your NAND
-		     as reliable as possible.
-- nand-is-boot-medium: Whether the NAND chip is a boot medium. Drivers might use
-		       this information to select ECC algorithms supported by
-		       the boot ROM or similar restrictions.
-
-- nand-rb: shall contain the native Ready/Busy ids.
-
-The ECC strength and ECC step size properties define the correction capability
-of a controller. Together, they say a controller can correct "{strength} bit
-errors per {size} bytes".
-
-The interpretation of these parameters is implementation-defined, so not all
-implementations must support all possible combinations. However, implementations
-are encouraged to further specify the value(s) they support.
-
-Example:
-
-	nand-controller {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		/* controller specific properties */
-
-		nand@0 {
-			reg = <0>;
-			nand-ecc-mode = "soft";
-			nand-ecc-algo = "bch";
-
-			/* controller specific properties */
-		};
-	};
diff --git a/dts/Bindings/mtd/partitions/arm,arm-firmware-suite.txt b/dts/Bindings/mtd/partitions/arm,arm-firmware-suite.txt
new file mode 100644
index 0000000000..d5c5616f6d
--- /dev/null
+++ b/dts/Bindings/mtd/partitions/arm,arm-firmware-suite.txt
@@ -0,0 +1,17 @@
+ARM AFS - ARM Firmware Suite Partitions
+=======================================
+
+The ARM Firmware Suite is a flash partitioning system found on the
+ARM reference designs: Integrator AP, Integrator CP, Versatile AB,
+Versatile PB, the RealView family, Versatile Express and Juno.
+
+Required properties:
+- compatible : (required) must be "arm,arm-firmware-suite"
+
+Example:
+
+flash@0 {
+	partitions {
+		compatible = "arm,arm-firmware-suite";
+	};
+};
diff --git a/dts/Bindings/mtd/partitions/brcm,bcm963xx-cfe-nor-partitions.txt b/dts/Bindings/mtd/partitions/brcm,bcm963xx-cfe-nor-partitions.txt
new file mode 100644
index 0000000000..9f630e95f1
--- /dev/null
+++ b/dts/Bindings/mtd/partitions/brcm,bcm963xx-cfe-nor-partitions.txt
@@ -0,0 +1,24 @@
+Broadcom BCM963XX CFE Loader NOR Flash Partitions
+=================================================
+
+Most Broadcom BCM63XX SoC based devices follow the Broadcom reference layout for
+NOR. The first erase block used for the CFE bootloader, the last for an
+NVRAM partition, and the remainder in-between for one to two firmware partitions
+at fixed offsets. A valid firmware partition is identified by the ImageTag
+header found at beginning of the second erase block, containing the rootfs and
+kernel offsets and sizes within the firmware partition.
+
+Required properties:
+- compatible : must be "brcm,bcm963xx-cfe-nor-partitions"
+
+Example:
+
+flash@1fc00000 {
+	compatible = "cfi-flash";
+	reg = <0x1fc00000 0x400000>;
+	bank-width = <2>;
+
+	partitions {
+		compatible = "brcm,bcm963xx-cfe-nor-partitions";
+	};
+};
diff --git a/dts/Bindings/mtd/partitions/brcm,bcm963xx-imagetag.txt b/dts/Bindings/mtd/partitions/brcm,bcm963xx-imagetag.txt
new file mode 100644
index 0000000000..f8b7418ed8
--- /dev/null
+++ b/dts/Bindings/mtd/partitions/brcm,bcm963xx-imagetag.txt
@@ -0,0 +1,45 @@
+Broadcom BCM963XX ImageTag Partition Container
+==============================================
+
+Some Broadcom BCM63XX SoC based devices contain additional, non discoverable
+partitions or non standard bootloader partition sizes. For these a mixed layout
+needs to be used with an explicit firmware partition.
+
+The BCM963XX ImageTag is a simple firmware header describing the offsets and
+sizes of the rootfs and kernel parts contained in the firmware.
+
+Required properties:
+- compatible : must be "brcm,bcm963xx-imagetag"
+
+Example:
+
+flash@1e000000 {
+	compatible = "cfi-flash";
+	reg = <0x1e000000 0x2000000>;
+	bank-width = <2>;
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		cfe@0 {
+			reg = <0x0 0x10000>;
+			read-only;
+		};
+
+		firmware@10000 {
+			reg = <0x10000 0x7d0000>;
+			compatible = "brcm,bcm963xx-imagetag";
+		};
+
+		caldata@7e0000 {
+			reg = <0x7e0000 0x10000>;
+			read-only;
+		};
+
+		nvram@7f0000 {
+			reg = <0x7f0000 0x10000>;
+		};
+	};
+};
diff --git a/dts/Bindings/mtd/sunxi-nand.txt b/dts/Bindings/mtd/sunxi-nand.txt
deleted file mode 100644
index dcd5a5d80d..0000000000
--- a/dts/Bindings/mtd/sunxi-nand.txt
+++ /dev/null
@@ -1,48 +0,0 @@
-Allwinner NAND Flash Controller (NFC)
-
-Required properties:
-- compatible : "allwinner,sun4i-a10-nand".
-- reg : shall contain registers location and length for data and reg.
-- interrupts : shall define the nand controller interrupt.
-- #address-cells: shall be set to 1. Encode the nand CS.
-- #size-cells : shall be set to 0.
-- clocks : shall reference nand controller clocks.
-- clock-names : nand controller internal clock names. Shall contain :
-    * "ahb" : AHB gating clock
-    * "mod" : nand controller clock
-
-Optional properties:
-- dmas : shall reference DMA channel associated to the NAND controller.
-- dma-names : shall be "rxtx".
-
-Optional children nodes:
-Children nodes represent the available nand chips.
-
-Optional properties:
-- reset : phandle + reset specifier pair
-- reset-names : must contain "ahb"
-- allwinner,rb : shall contain the native Ready/Busy ids.
-- nand-ecc-mode : one of the supported ECC modes ("hw", "soft", "soft_bch" or
-		  "none")
-
-see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings.
-
-
-Examples:
-nfc: nand@1c03000 {
-	compatible = "allwinner,sun4i-a10-nand";
-	reg = <0x01c03000 0x1000>;
-	interrupts = <0 37 1>;
-	clocks = <&ahb_gates 13>, <&nand_clk>;
-	clock-names = "ahb", "mod";
-	#address-cells = <1>;
-	#size-cells = <0>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&nand_pins_a &nand_cs0_pins_a &nand_rb0_pins_a>;
-
-	nand@0 {
-		reg = <0>;
-		allwinner,rb = <0>;
-		nand-ecc-mode = "soft_bch";
-	};
-};