dts: update to v4.7-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

2 files changed, 79 insertions, 7 deletions

diff --git a/dts/Bindings/net/wireless/marvell-sd8xxx.txt b/dts/Bindings/net/wireless/marvell-sd8xxx.txt
new file mode 100644
index 0000000000..c421aba0a5
--- /dev/null
+++ b/dts/Bindings/net/wireless/marvell-sd8xxx.txt
@@ -0,0 +1,63 @@
+Marvell 8897/8997 (sd8897/sd8997) SDIO devices
+------
+
+This node provides properties for controlling the marvell sdio wireless device.
+The node is expected to be specified as a child node to the SDIO controller that
+connects the device to the system.
+
+Required properties:
+
+  - compatible : should be one of the following:
+	* "marvell,sd8897"
+	* "marvell,sd8997"
+
+Optional properties:
+
+  - marvell,caldata* : A series of properties with marvell,caldata prefix,
+		      represent calibration data downloaded to the device during
+		      initialization. This is an array of unsigned 8-bit values.
+		      the properties should follow below property name and
+		      corresponding array length:
+	"marvell,caldata-txpwrlimit-2g" (length = 566).
+	"marvell,caldata-txpwrlimit-5g-sub0" (length = 502).
+	"marvell,caldata-txpwrlimit-5g-sub1" (length = 688).
+	"marvell,caldata-txpwrlimit-5g-sub2" (length = 750).
+	"marvell,caldata-txpwrlimit-5g-sub3" (length = 502).
+  - marvell,wakeup-pin : a wakeup pin number of wifi chip which will be configured
+		      to firmware. Firmware will wakeup the host using this pin
+		      during suspend/resume.
+  - interrupt-parent: phandle of the parent interrupt controller
+  - interrupts : interrupt pin number to the cpu. driver will request an irq based on
+		 this interrupt number. during system suspend, the irq will be enabled
+		 so that the wifi chip can wakeup host platform under certain condition.
+		 during system resume, the irq will be disabled to make sure
+		 unnecessary interrupt is not received.
+
+Example:
+
+Tx power limit calibration data is configured in below example.
+The calibration data is an array of unsigned values, the length
+can vary between hw versions.
+IRQ pin 38 is used as system wakeup source interrupt. wakeup pin 3 is configured
+so that firmware can wakeup host using this device side pin.
+
+&mmc3 {
+	status = "okay";
+	vmmc-supply = <&wlan_en_reg>;
+	bus-width = <4>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	mwifiex: wifi@1 {
+		compatible = "marvell,sd8897";
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
+
+		marvell,caldata_00_txpwrlimit_2g_cfg_set = /bits/ 8 <
+	0x01 0x00 0x06 0x00 0x08 0x02 0x89 0x01>;
+		marvell,wakeup-pin = <3>;
+	};
+};
diff --git a/dts/Bindings/net/wireless/qcom,ath10k.txt b/dts/Bindings/net/wireless/qcom,ath10k.txt
index 96aae6b4f7..74d7f0af20 100644
--- a/dts/Bindings/net/wireless/qcom,ath10k.txt
+++ b/dts/Bindings/net/wireless/qcom,ath10k.txt
@@ -5,12 +5,18 @@ Required properties:
 	* "qcom,ath10k"
 	* "qcom,ipq4019-wifi"
 
-PCI based devices uses compatible string "qcom,ath10k" and takes only
-calibration data via "qcom,ath10k-calibration-data". Rest of the properties
-are not applicable for PCI based devices.
+PCI based devices uses compatible string "qcom,ath10k" and takes calibration
+data along with board specific data via "qcom,ath10k-calibration-data".
+Rest of the properties are not applicable for PCI based devices.
 
 AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi"
-and also uses most of the properties defined in this doc.
+and also uses most of the properties defined in this doc (except
+"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data"
+to carry pre calibration data.
+
+In general, entry "qcom,ath10k-pre-calibration-data" and
+"qcom,ath10k-calibration-data" conflict with each other and only one
+can be provided per device.
 
 Optional properties:
 - reg: Address and length of the register set for the device.
@@ -35,8 +41,11 @@ Optional properties:
 - qcom,msi_addr: MSI interrupt address.
 - qcom,msi_base: Base value to add before writing MSI data into
 		MSI address register.
-- qcom,ath10k-calibration-data : calibration data as an array, the
-				 length can vary between hw versions
+- qcom,ath10k-calibration-data : calibration data + board specific data
+				 as an array, the length can vary between
+				 hw versions.
+- qcom,ath10k-pre-calibration-data : pre calibration data as an array,
+				     the length can vary between hw versions.
 
 Example (to supply the calibration data alone):
 
@@ -105,5 +114,5 @@ wifi0: wifi@a000000 {
 			  "legacy";
 	qcom,msi_addr = <0x0b006040>;
 	qcom,msi_base = <0x40>;
-	qcom,ath10k-calibration-data = [ 01 02 03 ... ];
+	qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ];
 };