dts: update to v4.11-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

2 files changed, 30 insertions, 1 deletions

diff --git a/dts/Bindings/net/wireless/ieee80211.txt b/dts/Bindings/net/wireless/ieee80211.txt
new file mode 100644
index 0000000000..f6442b1397
--- /dev/null
+++ b/dts/Bindings/net/wireless/ieee80211.txt
@@ -0,0 +1,24 @@
+Common IEEE 802.11 properties
+
+This provides documentation of common properties that are valid for all wireless
+devices.
+
+Optional properties:
+ - ieee80211-freq-limit : list of supported frequency ranges in KHz. This can be
+	used for devices that in a given config support less channels than
+	normally. It may happen chipset supports a wide wireless band but it is
+	limited to some part of it due to used antennas or power amplifier.
+	An example case for this can be tri-band wireless router with two
+	identical chipsets used for two different 5 GHz subbands. Using them
+	incorrectly could not work or decrease performance noticeably.
+
+Example:
+
+pcie@0,0 {
+	reg = <0x0000 0 0 0 0>;
+	wifi@0,0 {
+		reg = <0x0000 0 0 0 0>;
+		ieee80211-freq-limit = <2402000 2482000>,
+				       <5170000 5250000>;
+	};
+};
diff --git a/dts/Bindings/net/wireless/marvell-8xxx.txt b/dts/Bindings/net/wireless/marvell-8xxx.txt
index 980b16df74..0854451ff9 100644
--- a/dts/Bindings/net/wireless/marvell-8xxx.txt
+++ b/dts/Bindings/net/wireless/marvell-8xxx.txt
@@ -1,4 +1,4 @@
-Marvell 8897/8997 (sd8897/sd8997/pcie8997) SDIO/PCIE devices
+Marvell 8787/8897/8997 (sd8787/sd8897/sd8997/pcie8997) SDIO/PCIE devices
 ------
 
 This node provides properties for controlling the Marvell SDIO/PCIE wireless device.
@@ -8,6 +8,7 @@ connects the device to the system.
 Required properties:
 
   - compatible : should be one of the following:
+	* "marvell,sd8787"
 	* "marvell,sd8897"
 	* "marvell,sd8997"
 	* "pci11ab,2b42"
@@ -34,6 +35,9 @@ Optional properties:
 		 so that the wifi chip can wakeup host platform under certain condition.
 		 during system resume, the irq will be disabled to make sure
 		 unnecessary interrupt is not received.
+  - vmmc-supply: a phandle of a regulator, supplying VCC to the card
+  - mmc-pwrseq:  phandle to the MMC power sequence node. See "mmc-pwrseq-*"
+		 for documentation of MMC power sequence bindings.
 
 Example:
 
@@ -46,6 +50,7 @@ so that firmware can wakeup host using this device side pin.
 &mmc3 {
 	status = "okay";
 	vmmc-supply = <&wlan_en_reg>;
+	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
 	cap-power-off-card;
 	keep-power-in-suspend;