dts: update to v4.16-rc1

Also includeded:

ARM: dts: am33xx: do not delete no longer existing clocks

Several clocks are removed from the am33xx dts files with v4.16-rc1.
Remove the corresponding /delete-node/ directives aswell to avoid
dtc breakage.

Also included:

ARM: dts: imx6qdl: SolidRun: Fix upstream include

Upstream dts file way renamed, so change include name accordingly.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

19 files changed, 320 insertions, 17 deletions

diff --git a/dts/Bindings/net/brcm,bcm7445-switch-v4.0.txt b/dts/Bindings/net/brcm,bcm7445-switch-v4.0.txt
index 9a734d808a..b7336b9d6a 100644
--- a/dts/Bindings/net/brcm,bcm7445-switch-v4.0.txt
+++ b/dts/Bindings/net/brcm,bcm7445-switch-v4.0.txt
@@ -2,7 +2,10 @@
 
 Required properties:
 
-- compatible: should be "brcm,bcm7445-switch-v4.0" or "brcm,bcm7278-switch-v4.0"
+- compatible: should be one of
+	"brcm,bcm7445-switch-v4.0"
+	"brcm,bcm7278-switch-v4.0"
+	"brcm,bcm7278-switch-v4.8"
 - reg: addresses and length of the register sets for the device, must be 6
   pairs of register addresses and lengths
 - interrupts: interrupts for the devices, must be two interrupts
diff --git a/dts/Bindings/net/can/can-transceiver.txt b/dts/Bindings/net/can/can-transceiver.txt
new file mode 100644
index 0000000000..0011f53ff1
--- /dev/null
+++ b/dts/Bindings/net/can/can-transceiver.txt
@@ -0,0 +1,24 @@
+Generic CAN transceiver Device Tree binding
+------------------------------
+
+CAN transceiver typically limits the max speed in standard CAN and CAN FD
+modes. Typically these limitations are static and the transceivers themselves
+provide no way to detect this limitation at runtime. For this situation,
+the "can-transceiver" node can be used.
+
+Required Properties:
+ max-bitrate:	a positive non 0 value that determines the max
+		speed that CAN/CAN-FD can run. Any other value
+		will be ignored.
+
+Examples:
+
+Based on Texas Instrument's TCAN1042HGV CAN Transceiver
+
+m_can0 {
+	....
+	can-transceiver {
+		max-bitrate = <5000000>;
+	};
+	...
+};
diff --git a/dts/Bindings/net/can/fsl-flexcan.txt b/dts/Bindings/net/can/fsl-flexcan.txt
index 56d6cc336e..bfc0c43365 100644
--- a/dts/Bindings/net/can/fsl-flexcan.txt
+++ b/dts/Bindings/net/can/fsl-flexcan.txt
@@ -18,6 +18,12 @@ Optional properties:
 
 - xceiver-supply: Regulator that powers the CAN transceiver
 
+- big-endian: This means the registers of FlexCAN controller are big endian.
+              This is optional property.i.e. if this property is not present in
+              device tree node then controller is assumed to be little endian.
+              if this property is present then controller is assumed to be big
+              endian.
+
 Example:
 
 	can@1c000 {
diff --git a/dts/Bindings/net/can/m_can.txt b/dts/Bindings/net/can/m_can.txt
index 63e90421d0..ed614383af 100644
--- a/dts/Bindings/net/can/m_can.txt
+++ b/dts/Bindings/net/can/m_can.txt
@@ -43,6 +43,11 @@ Required properties:
 			  Please refer to 2.4.1 Message RAM Configuration in
 			  Bosch M_CAN user manual for details.
 
+Optional Subnode:
+- can-transceiver	: Can-transceiver subnode describing maximum speed
+			  that can be used for CAN/CAN-FD modes. See
+			  Documentation/devicetree/bindings/net/can/can-transceiver.txt
+			  for details.
 Example:
 SoC dtsi:
 m_can1: can@20e8000 {
@@ -63,4 +68,8 @@ Board dts:
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_m_can1>;
 	status = "enabled";
+
+	can-transceiver {
+		max-bitrate = <5000000>;
+	};
 };
diff --git a/dts/Bindings/net/can/rcar_can.txt b/dts/Bindings/net/can/rcar_can.txt
index 06bb7cc334..94a7f33ac5 100644
--- a/dts/Bindings/net/can/rcar_can.txt
+++ b/dts/Bindings/net/can/rcar_can.txt
@@ -2,7 +2,9 @@ Renesas R-Car CAN controller Device Tree Bindings
 -------------------------------------------------
 
 Required properties:
-- compatible: "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC.
+- compatible: "renesas,can-r8a7743" if CAN controller is a part of R8A7743 SoC.
+	      "renesas,can-r8a7745" if CAN controller is a part of R8A7745 SoC.
+	      "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC.
 	      "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC.
 	      "renesas,can-r8a7790" if CAN controller is a part of R8A7790 SoC.
 	      "renesas,can-r8a7791" if CAN controller is a part of R8A7791 SoC.
@@ -12,7 +14,8 @@ Required properties:
 	      "renesas,can-r8a7795" if CAN controller is a part of R8A7795 SoC.
 	      "renesas,can-r8a7796" if CAN controller is a part of R8A7796 SoC.
 	      "renesas,rcar-gen1-can" for a generic R-Car Gen1 compatible device.
-	      "renesas,rcar-gen2-can" for a generic R-Car Gen2 compatible device.
+	      "renesas,rcar-gen2-can" for a generic R-Car Gen2 or RZ/G1
+	      compatible device.
 	      "renesas,rcar-gen3-can" for a generic R-Car Gen3 compatible device.
 	      When compatible with the generic version, nodes must list the
 	      SoC-specific version corresponding to the platform first
diff --git a/dts/Bindings/net/cortina,gemini-ethernet.txt b/dts/Bindings/net/cortina,gemini-ethernet.txt
new file mode 100644
index 0000000000..6c559981d1
--- /dev/null
+++ b/dts/Bindings/net/cortina,gemini-ethernet.txt
@@ -0,0 +1,92 @@
+Cortina Systems Gemini Ethernet Controller
+==========================================
+
+This ethernet controller is found in the Gemini SoC family:
+StorLink SL3512 and SL3516, also known as Cortina Systems
+CS3512 and CS3516.
+
+Required properties:
+- compatible: must be "cortina,gemini-ethernet"
+- reg: must contain the global registers and the V-bit and A-bit
+  memory areas, in total three register sets.
+- syscon: a phandle to the system controller
+- #address-cells: must be specified, must be <1>
+- #size-cells: must be specified, must be <1>
+- ranges: should be state like this giving a 1:1 address translation
+  for the subnodes
+
+The subnodes represents the two ethernet ports in this device.
+They are not independent of each other since they share resources
+in the parent node, and are thus children.
+
+Required subnodes:
+- port0: contains the resources for ethernet port 0
+- port1: contains the resources for ethernet port 1
+
+Required subnode properties:
+- compatible: must be "cortina,gemini-ethernet-port"
+- reg: must contain two register areas: the DMA/TOE memory and
+  the GMAC memory area of the port
+- interrupts: should contain the interrupt line of the port.
+  this is nominally a level interrupt active high.
+- resets: this must provide an SoC-integrated reset line for
+  the port.
+- clocks: this should contain a handle to the PCLK clock for
+  clocking the silicon in this port
+- clock-names: must be "PCLK"
+
+Optional subnode properties:
+- phy-mode: see ethernet.txt
+- phy-handle: see ethernet.txt
+
+Example:
+
+mdio-bus {
+	(...)
+	phy0: ethernet-phy@1 {
+		reg = <1>;
+		device_type = "ethernet-phy";
+	};
+	phy1: ethernet-phy@3 {
+		reg = <3>;
+		device_type = "ethernet-phy";
+	};
+};
+
+
+ethernet@60000000 {
+	compatible = "cortina,gemini-ethernet";
+	reg = <0x60000000 0x4000>, /* Global registers, queue */
+	      <0x60004000 0x2000>, /* V-bit */
+	      <0x60006000 0x2000>; /* A-bit */
+	syscon = <&syscon>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	gmac0: ethernet-port@0 {
+		compatible = "cortina,gemini-ethernet-port";
+		reg = <0x60008000 0x2000>, /* Port 0 DMA/TOE */
+		      <0x6000a000 0x2000>; /* Port 0 GMAC */
+		interrupt-parent = <&intcon>;
+		interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
+		resets = <&syscon GEMINI_RESET_GMAC0>;
+		clocks = <&syscon GEMINI_CLK_GATE_GMAC0>;
+		clock-names = "PCLK";
+		phy-mode = "rgmii";
+		phy-handle = <&phy0>;
+	};
+
+	gmac1: ethernet-port@1 {
+		compatible = "cortina,gemini-ethernet-port";
+		reg = <0x6000c000 0x2000>, /* Port 1 DMA/TOE */
+		      <0x6000e000 0x2000>; /* Port 1 GMAC */
+		interrupt-parent = <&intcon>;
+		interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+		resets = <&syscon GEMINI_RESET_GMAC1>;
+		clocks = <&syscon GEMINI_CLK_GATE_GMAC1>;
+		clock-names = "PCLK";
+		phy-mode = "rgmii";
+		phy-handle = <&phy1>;
+	};
+};
diff --git a/dts/Bindings/net/cpsw.txt b/dts/Bindings/net/cpsw.txt
index 7cc15c96ea..4cb4925a28 100644
--- a/dts/Bindings/net/cpsw.txt
+++ b/dts/Bindings/net/cpsw.txt
@@ -61,7 +61,7 @@ file.
 
 Examples:
 
-	mac: ethernet@4A100000 {
+	mac: ethernet@4a100000 {
 		compatible = "ti,cpsw";
 		reg = <0x4A100000 0x1000>;
 		interrupts = <55 0x4>;
@@ -91,7 +91,7 @@ Examples:
 	};
 
 (or)
-	mac: ethernet@4A100000 {
+	mac: ethernet@4a100000 {
 		compatible = "ti,cpsw";
 		ti,hwmods = "cpgmac0";
 		cpdma_channels = <8>;
diff --git a/dts/Bindings/net/davinci-mdio.txt b/dts/Bindings/net/davinci-mdio.txt
index 621156ca4f..e6527de80f 100644
--- a/dts/Bindings/net/davinci-mdio.txt
+++ b/dts/Bindings/net/davinci-mdio.txt
@@ -21,7 +21,7 @@ file.
 
 Examples:
 
-	mdio: davinci_mdio@4A101000 {
+	mdio: davinci_mdio@4a101000 {
 		compatible = "ti,davinci_mdio";
 		reg = <0x4A101000 0x1000>;
 		bus_freq = <1000000>;
@@ -29,7 +29,7 @@ Examples:
 
 (or)
 
-	mdio: davinci_mdio@4A101000 {
+	mdio: davinci_mdio@4a101000 {
 		compatible = "ti,davinci_mdio";
 		ti,hwmods = "davinci_mdio";
 		bus_freq = <1000000>;
diff --git a/dts/Bindings/net/fsl-fec.txt b/dts/Bindings/net/fsl-fec.txt
index f0dc944091..2d41fb96ce 100644
--- a/dts/Bindings/net/fsl-fec.txt
+++ b/dts/Bindings/net/fsl-fec.txt
@@ -59,7 +59,7 @@ ethernet@83fec000 {
 	reg = <0x83fec000 0x4000>;
 	interrupts = <87>;
 	phy-mode = "mii";
-	phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */
+	phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */
 	local-mac-address = [00 04 9F 01 1B B9];
 	phy-supply = <&reg_fec_supply>;
 };
@@ -71,7 +71,7 @@ ethernet@83fec000 {
 	reg = <0x83fec000 0x4000>;
 	interrupts = <87>;
 	phy-mode = "mii";
-	phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */
+	phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */
 	local-mac-address = [00 04 9F 01 1B B9];
 	phy-supply = <&reg_fec_supply>;
 	phy-handle = <&ethphy>;
diff --git a/dts/Bindings/net/fsl-tsec-phy.txt b/dts/Bindings/net/fsl-tsec-phy.txt
index db74f0dc29..594982c6b9 100644
--- a/dts/Bindings/net/fsl-tsec-phy.txt
+++ b/dts/Bindings/net/fsl-tsec-phy.txt
@@ -136,7 +136,7 @@ Clock Properties:
 
 Example:
 
-	ptp_clock@24E00 {
+	ptp_clock@24e00 {
 		compatible = "fsl,etsec-ptp";
 		reg = <0x24E00 0xB0>;
 		interrupts = <12 0x8 13 0x8>;
diff --git a/dts/Bindings/net/ieee802154/adf7242.txt b/dts/Bindings/net/ieee802154/adf7242.txt
index dea5124cdc..d24172cc6d 100644
--- a/dts/Bindings/net/ieee802154/adf7242.txt
+++ b/dts/Bindings/net/ieee802154/adf7242.txt
@@ -1,7 +1,7 @@
 * ADF7242 IEEE 802.15.4 *
 
 Required properties:
-  - compatible:		should be "adi,adf7242"
+  - compatible:		should be "adi,adf7242", "adi,adf7241"
   - spi-max-frequency:	maximal bus speed (12.5 MHz)
   - reg:		the chipselect index
   - interrupts:		the interrupt generated by the device via pin IRQ1.
diff --git a/dts/Bindings/net/mediatek-net.txt b/dts/Bindings/net/mediatek-net.txt
index 214eaa9a66..53c13ee384 100644
--- a/dts/Bindings/net/mediatek-net.txt
+++ b/dts/Bindings/net/mediatek-net.txt
@@ -28,7 +28,7 @@ Required properties:
 - mediatek,sgmiisys: phandle to the syscon node that handles the SGMII setup
 	which is required for those SoCs equipped with SGMII such as MT7622 SoC.
 - mediatek,pctl: phandle to the syscon node that handles the ports slew rate
-	and driver current
+	and driver current: only for MT2701 and MT7623 SoC
 
 Optional properties:
 - interrupt-parent: Should be the phandle for the interrupt controller
diff --git a/dts/Bindings/net/phy.txt b/dts/Bindings/net/phy.txt
index 77d0b2a61f..d2169a56f5 100644
--- a/dts/Bindings/net/phy.txt
+++ b/dts/Bindings/net/phy.txt
@@ -53,6 +53,14 @@ Optional Properties:
   to ensure the integrated PHY is used. The absence of this property indicates
   the muxers should be configured so that the external PHY is used.
 
+- reset-gpios: The GPIO phandle and specifier for the PHY reset signal.
+
+- reset-assert-us: Delay after the reset was asserted in microseconds.
+  If this property is missing the delay will be skipped.
+
+- reset-deassert-us: Delay after the reset was deasserted in microseconds.
+  If this property is missing the delay will be skipped.
+
 Example:
 
 ethernet-phy@0 {
@@ -60,4 +68,8 @@ ethernet-phy@0 {
 	interrupt-parent = <&PIC>;
 	interrupts = <35 IRQ_TYPE_EDGE_RISING>;
 	reg = <0>;
+
+	reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	reset-assert-us = <1000>;
+	reset-deassert-us = <2000>;
 };
diff --git a/dts/Bindings/net/sff,sfp.txt b/dts/Bindings/net/sff,sfp.txt
index 60e970ce10..f1c441bedf 100644
--- a/dts/Bindings/net/sff,sfp.txt
+++ b/dts/Bindings/net/sff,sfp.txt
@@ -3,7 +3,9 @@ Transceiver
 
 Required properties:
 
-- compatible : must be "sff,sfp"
+- compatible : must be one of
+  "sff,sfp" for SFP modules
+  "sff,sff" for soldered down SFF modules
 
 Optional Properties:
 
@@ -11,7 +13,8 @@ Optional Properties:
   interface
 
 - mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS)
-  module presence input gpio signal, active (module absent) high
+  module presence input gpio signal, active (module absent) high. Must
+  not be present for SFF modules
 
 - los-gpios : GPIO phandle and a specifier of the Receiver Loss of Signal
   Indication input gpio signal, active (signal lost) high
@@ -24,10 +27,11 @@ Optional Properties:
 
 - rate-select0-gpios : GPIO phandle and a specifier of the Rx Signaling Rate
   Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx rate
+  Must not be present for SFF modules
 
 - rate-select1-gpios : GPIO phandle and a specifier of the Tx Signaling Rate
   Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high:
-  high Tx rate
+  high Tx rate. Must not be present for SFF modules
 
 Example #1: Direct serdes to SFP connection
 
diff --git a/dts/Bindings/net/socionext,uniphier-ave4.txt b/dts/Bindings/net/socionext,uniphier-ave4.txt
new file mode 100644
index 0000000000..270ea4efff
--- /dev/null
+++ b/dts/Bindings/net/socionext,uniphier-ave4.txt
@@ -0,0 +1,48 @@
+* Socionext AVE ethernet controller
+
+This describes the devicetree bindings for AVE ethernet controller
+implemented on Socionext UniPhier SoCs.
+
+Required properties:
+ - compatible: Should be
+	- "socionext,uniphier-pro4-ave4" : for Pro4 SoC
+	- "socionext,uniphier-pxs2-ave4" : for PXs2 SoC
+	- "socionext,uniphier-ld11-ave4" : for LD11 SoC
+	- "socionext,uniphier-ld20-ave4" : for LD20 SoC
+ - reg: Address where registers are mapped and size of region.
+ - interrupts: Should contain the MAC interrupt.
+ - phy-mode: See ethernet.txt in the same directory. Allow to choose
+	"rgmii", "rmii", or "mii" according to the PHY.
+ - phy-handle: Should point to the external phy device.
+	See ethernet.txt file in the same directory.
+ - clocks: A phandle to the clock for the MAC.
+
+Optional properties:
+ - resets: A phandle to the reset control for the MAC.
+ - local-mac-address: See ethernet.txt in the same directory.
+
+Required subnode:
+ - mdio: A container for child nodes representing phy nodes.
+         See phy.txt in the same directory.
+
+Example:
+
+	ether: ethernet@65000000 {
+		compatible = "socionext,uniphier-ld20-ave4";
+		reg = <0x65000000 0x8500>;
+		interrupts = <0 66 4>;
+		phy-mode = "rgmii";
+		phy-handle = <&ethphy>;
+		clocks = <&sys_clk 6>;
+		resets = <&sys_rst 6>;
+		local-mac-address = [00 00 00 00 00 00];
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ethphy: ethphy@1 {
+				reg = <1>;
+			};
+		};
+	};
diff --git a/dts/Bindings/net/socionext-netsec.txt b/dts/Bindings/net/socionext-netsec.txt
new file mode 100644
index 0000000000..0cff94fb04
--- /dev/null
+++ b/dts/Bindings/net/socionext-netsec.txt
@@ -0,0 +1,53 @@
+* Socionext NetSec Ethernet Controller IP
+
+Required properties:
+- compatible: Should be "socionext,synquacer-netsec"
+- reg: Address and length of the control register area, followed by the
+       address and length of the EEPROM holding the MAC address and
+       microengine firmware
+- interrupts: Should contain ethernet controller interrupt
+- clocks: phandle to the PHY reference clock
+- clock-names: Should be "phy_ref_clk"
+- phy-mode: See ethernet.txt file in the same directory
+- phy-handle: See ethernet.txt in the same directory.
+
+- mdio device tree subnode: When the Netsec has a phy connected to its local
+		mdio, there must be device tree subnode with the following
+		required properties:
+
+	- #address-cells: Must be <1>.
+	- #size-cells: Must be <0>.
+
+	For each phy on the mdio bus, there must be a node with the following
+	fields:
+	- compatible: Refer to phy.txt
+	- reg: phy id used to communicate to phy.
+
+Optional properties: (See ethernet.txt file in the same directory)
+- dma-coherent: Boolean property, must only be present if memory
+	accesses performed by the device are cache coherent.
+- local-mac-address: See ethernet.txt in the same directory.
+- mac-address: See ethernet.txt in the same directory.
+- max-speed: See ethernet.txt in the same directory.
+- max-frame-size: See ethernet.txt in the same directory.
+
+Example:
+	eth0: ethernet@522d0000 {
+		compatible = "socionext,synquacer-netsec";
+		reg = <0 0x522d0000 0x0 0x10000>, <0 0x10000000 0x0 0x10000>;
+		interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_netsec>;
+		clock-names = "phy_ref_clk";
+		phy-mode = "rgmii";
+		max-speed = <1000>;
+		max-frame-size = <9000>;
+		phy-handle = <&phy1>;
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			phy1: ethernet-phy@1 {
+				compatible = "ethernet-phy-ieee802.3-c22";
+				reg = <1>;
+			};
+		};
diff --git a/dts/Bindings/net/ti,wilink-st.txt b/dts/Bindings/net/ti-bluetooth.txt
index 1649c1f66b..6d03ff8c70 100644
--- a/dts/Bindings/net/ti,wilink-st.txt
+++ b/dts/Bindings/net/ti-bluetooth.txt
@@ -1,10 +1,18 @@
-TI WiLink 7/8 (wl12xx/wl18xx) Shared Transport BT/FM/GPS devices
+Texas Instruments Bluetooth Chips
+---------------------------------
+
+This documents the binding structure and common properties for serial
+attached TI Bluetooth devices. The following chips are included in this
+binding:
+
+* TI CC256x Bluetooth devices
+* TI WiLink 7/8 (wl12xx/wl18xx) Shared Transport BT/FM/GPS devices
 
 TI WiLink devices have a UART interface for providing Bluetooth, FM radio,
 and GPS over what's called "shared transport". The shared transport is
 standard BT HCI protocol with additional channels for the other functions.
 
-These devices also have a separate WiFi interface as described in
+TI WiLink devices also have a separate WiFi interface as described in
 wireless/ti,wlcore.txt.
 
 This bindings follows the UART slave device binding in
@@ -12,6 +20,7 @@ This bindings follows the UART slave device binding in
 
 Required properties:
  - compatible: should be one of the following:
+    "ti,cc2560"
     "ti,wl1271-st"
     "ti,wl1273-st"
     "ti,wl1281-st"
@@ -32,6 +41,9 @@ Optional properties:
    See ../clocks/clock-bindings.txt for details.
  - clock-names : Must include the following entry:
    "ext_clock" (External clock provided to the TI combo chip).
+ - nvmem-cells: phandle to nvmem data cell that contains a 6 byte BD address
+   with the most significant byte first (big-endian).
+ - nvmem-cell-names: "bd-address" (required when nvmem-cells is specified)
 
 Example:
 
@@ -43,5 +55,7 @@ Example:
 		enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
 		clocks = <&clk32k_wl18xx>;
 		clock-names = "ext_clock";
+		nvmem-cells = <&bd_address>;
+		nvmem-cell-names = "bd-address";
 	};
 };
diff --git a/dts/Bindings/net/wireless/mediatek,mt76.txt b/dts/Bindings/net/wireless/mediatek,mt76.txt
new file mode 100644
index 0000000000..0c17a0ec9b
--- /dev/null
+++ b/dts/Bindings/net/wireless/mediatek,mt76.txt
@@ -0,0 +1,32 @@
+* MediaTek mt76xx devices
+
+This node provides properties for configuring the MediaTek mt76xx wireless
+device. The node is expected to be specified as a child node of the PCI
+controller to which the wireless chip is connected.
+
+Optional properties:
+
+- mac-address: See ethernet.txt in the parent directory
+- local-mac-address: See ethernet.txt in the parent directory
+- ieee80211-freq-limit: See ieee80211.txt
+- mediatek,mtd-eeprom: Specify a MTD partition + offset containing EEPROM data
+
+Optional nodes:
+- led: Properties for a connected LED
+  Optional properties:
+    - led-sources: See Documentation/devicetree/bindings/leds/common.txt
+
+&pcie {
+	pcie0 {
+		wifi@0,0 {
+			compatible = "mediatek,mt76";
+			reg = <0x0000 0 0 0 0>;
+			ieee80211-freq-limit = <5000000 6000000>;
+			mediatek,mtd-eeprom = <&factory 0x8000>;
+
+			led {
+				led-sources = <2>;
+			};
+		};
+	};
+};
diff --git a/dts/Bindings/net/wireless/qcom,ath10k.txt b/dts/Bindings/net/wireless/qcom,ath10k.txt
index 74d7f0af20..3d2a031217 100644
--- a/dts/Bindings/net/wireless/qcom,ath10k.txt
+++ b/dts/Bindings/net/wireless/qcom,ath10k.txt
@@ -41,6 +41,9 @@ Optional properties:
 - qcom,msi_addr: MSI interrupt address.
 - qcom,msi_base: Base value to add before writing MSI data into
 		MSI address register.
+- qcom,ath10k-calibration-variant: string to search for in the board-2.bin
+				   variant list with the same bus and device
+				   specific ids
 - qcom,ath10k-calibration-data : calibration data + board specific data
 				 as an array, the length can vary between
 				 hw versions.