dts: update to v4.20-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

12 files changed, 348 insertions, 16 deletions

diff --git a/dts/Bindings/phy/brcm-sata-phy.txt b/dts/Bindings/phy/brcm-sata-phy.txt
index 0aced97d80..b640845fec 100644
--- a/dts/Bindings/phy/brcm-sata-phy.txt
+++ b/dts/Bindings/phy/brcm-sata-phy.txt
@@ -8,6 +8,7 @@ Required properties:
      "brcm,iproc-nsp-sata-phy"
      "brcm,phy-sata3"
      "brcm,iproc-sr-sata-phy"
+     "brcm,bcm63138-sata-phy"
 - address-cells: should be 1
 - size-cells: should be 0
 - reg: register ranges for the PHY PCB interface
diff --git a/dts/Bindings/phy/phy-cadence-dp.txt b/dts/Bindings/phy/phy-cadence-dp.txt
new file mode 100644
index 0000000000..7f49fd54eb
--- /dev/null
+++ b/dts/Bindings/phy/phy-cadence-dp.txt
@@ -0,0 +1,30 @@
+Cadence MHDP DisplayPort SD0801 PHY binding
+===========================================
+
+This binding describes the Cadence SD0801 PHY hardware included with
+the Cadence MHDP DisplayPort controller.
+
+-------------------------------------------------------------------------------
+Required properties (controller (parent) node):
+- compatible	: Should be "cdns,dp-phy"
+- reg		: Defines the following sets of registers in the parent
+		  mhdp device:
+			- Offset of the DPTX PHY configuration registers
+			- Offset of the SD0801 PHY configuration registers
+- #phy-cells	: from the generic PHY bindings, must be 0.
+
+Optional properties:
+- num_lanes	: Number of DisplayPort lanes to use (1, 2 or 4)
+- max_bit_rate	: Maximum DisplayPort link bit rate to use, in Mbps (2160,
+		  2430, 2700, 3240, 4320, 5400 or 8100)
+-------------------------------------------------------------------------------
+
+Example:
+	dp_phy: phy@f0fb030a00 {
+		compatible = "cdns,dp-phy";
+		reg = <0xf0 0xfb030a00 0x0 0x00000040>,
+		      <0xf0 0xfb500000 0x0 0x00100000>;
+		num_lanes = <4>;
+		max_bit_rate = <8100>;
+		#phy-cells = <0>;
+	};
diff --git a/dts/Bindings/phy/phy-ocelot-serdes.txt b/dts/Bindings/phy/phy-ocelot-serdes.txt
new file mode 100644
index 0000000000..3322198601
--- /dev/null
+++ b/dts/Bindings/phy/phy-ocelot-serdes.txt
@@ -0,0 +1,43 @@
+Microsemi Ocelot SerDes muxing driver
+-------------------------------------
+
+On Microsemi Ocelot, there is a handful of registers in HSIO address
+space for setting up the SerDes to switch port muxing.
+
+A SerDes X can be "muxed" to work with switch port Y or Z for example.
+One specific SerDes can also be used as a PCIe interface.
+
+Hence, a SerDes represents an interface, be it an Ethernet or a PCIe one.
+
+There are two kinds of SerDes: SERDES1G supports 10/100Mbps in
+half/full-duplex and 1000Mbps in full-duplex mode while SERDES6G supports
+10/100Mbps in half/full-duplex and 1000/2500Mbps in full-duplex mode.
+
+Also, SERDES6G number (aka "macro") 0 is the only interface supporting
+QSGMII.
+
+This is a child of the HSIO syscon ("mscc,ocelot-hsio", see
+Documentation/devicetree/bindings/mips/mscc.txt) on the Microsemi Ocelot.
+
+Required properties:
+
+- compatible: should be "mscc,vsc7514-serdes"
+- #phy-cells : from the generic phy bindings, must be 2.
+	       The first number defines the input port to use for a given
+	       SerDes macro. The second defines the macro to use. They are
+	       defined in dt-bindings/phy/phy-ocelot-serdes.h
+
+Example:
+
+	serdes: serdes {
+		compatible = "mscc,vsc7514-serdes";
+		#phy-cells = <2>;
+	};
+
+	ethernet {
+		port1 {
+			phy-handle = <&phy_foo>;
+			/* Link SERDES1G_5 to port1 */
+			phys = <&serdes 1 SERDES1G_5>;
+		};
+	};
diff --git a/dts/Bindings/phy/phy-rockchip-inno-hdmi.txt b/dts/Bindings/phy/phy-rockchip-inno-hdmi.txt
new file mode 100644
index 0000000000..710cccd5ee
--- /dev/null
+++ b/dts/Bindings/phy/phy-rockchip-inno-hdmi.txt
@@ -0,0 +1,43 @@
+ROCKCHIP HDMI PHY WITH INNO IP BLOCK
+
+Required properties:
+ - compatible : should be one of the listed compatibles:
+	* "rockchip,rk3228-hdmi-phy",
+	* "rockchip,rk3328-hdmi-phy";
+ - reg : Address and length of the hdmi phy control register set
+ - clocks : phandle + clock specifier for the phy clocks
+ - clock-names : string, clock name, must contain "sysclk" for system
+	  control and register configuration, "refoclk" for crystal-
+	  oscillator reference PLL clock input and "refpclk" for pclk-
+	  based refeference PLL clock input.
+ - #clock-cells: should be 0.
+ - clock-output-names : shall be the name for the output clock.
+ - interrupts : phandle + interrupt specified for the hdmiphy interrupt
+ - #phy-cells : must be 0. See ./phy-bindings.txt for details.
+
+Optional properties for rk3328-hdmi-phy:
+ - nvmem-cells = phandle + nvmem specifier for the cpu-version efuse
+ - nvmem-cell-names : "cpu-version" to read the chip version, required
+	  for adjustment to some frequency settings
+
+Example:
+	hdmi_phy: hdmi-phy@12030000 {
+		compatible = "rockchip,rk3228-hdmi-phy";
+		reg = <0x12030000 0x10000>;
+		#phy-cells = <0>;
+		clocks = <&cru PCLK_HDMI_PHY>, <&xin24m>, <&cru DCLK_HDMIPHY>;
+		clock-names = "sysclk", "refoclk", "refpclk";
+		#clock-cells = <0>;
+		clock-output-names = "hdmi_phy";
+		status = "disabled";
+	};
+
+Then the PHY can be used in other nodes such as:
+
+	hdmi: hdmi@200a0000 {
+		compatible = "rockchip,rk3228-dw-hdmi";
+		...
+		phys = <&hdmi_phy>;
+		phy-names = "hdmi";
+		...
+	};
diff --git a/dts/Bindings/phy/qcom-qmp-phy.txt b/dts/Bindings/phy/qcom-qmp-phy.txt
index 0c7629e88b..adf20b2bdf 100644
--- a/dts/Bindings/phy/qcom-qmp-phy.txt
+++ b/dts/Bindings/phy/qcom-qmp-phy.txt
@@ -10,16 +10,20 @@ Required properties:
 	       "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
 	       "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996,
 	       "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845,
-	       "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845.
+	       "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845,
+	       "qcom,sdm845-qmp-ufs-phy" for UFS QMP phy on sdm845.
 
- - reg:
-   - For "qcom,sdm845-qmp-usb3-phy":
-     - index 0: address and length of register set for PHY's common serdes
-       block.
-     - named register "dp_com" (using reg-names): address and length of the
-       DP_COM control block.
-   - For all others:
-     - offset and length of register set for PHY's common serdes block.
+- reg:
+  - index 0: address and length of register set for PHY's common
+             serdes block.
+  - index 1: address and length of the DP_COM control block (for
+             "qcom,sdm845-qmp-usb3-phy" only).
+
+- reg-names:
+  - For "qcom,sdm845-qmp-usb3-phy":
+    - Should be: "reg-base", "dp_com"
+  - For all others:
+    - The reg-names property shouldn't be defined.
 
  - #clock-cells: must be 1
     - Phy pll outputs a bunch of clocks for Tx, Rx and Pipe
@@ -35,6 +39,7 @@ Required properties:
 		"aux" for phy aux clock,
 		"ref" for 19.2 MHz ref clk,
 		"com_aux" for phy common block aux clock,
+		"ref_aux" for phy reference aux clock,
 		For "qcom,msm8996-qmp-pcie-phy" must contain:
 			"aux", "cfg_ahb", "ref".
 		For "qcom,msm8996-qmp-usb3-phy" must contain:
diff --git a/dts/Bindings/phy/rcar-gen2-phy.txt b/dts/Bindings/phy/rcar-gen2-phy.txt
index eeb9e1874e..4f0879a0ca 100644
--- a/dts/Bindings/phy/rcar-gen2-phy.txt
+++ b/dts/Bindings/phy/rcar-gen2-phy.txt
@@ -5,6 +5,7 @@ This file provides information on what the device node for the R-Car generation
 
 Required properties:
 - compatible: "renesas,usb-phy-r8a7743" if the device is a part of R8A7743 SoC.
+	      "renesas,usb-phy-r8a7744" if the device is a part of R8A7744 SoC.
 	      "renesas,usb-phy-r8a7745" if the device is a part of R8A7745 SoC.
 	      "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC.
 	      "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC.
diff --git a/dts/Bindings/phy/rcar-gen3-phy-usb2.txt b/dts/Bindings/phy/rcar-gen3-phy-usb2.txt
index fb4a204da2..de7b5393c1 100644
--- a/dts/Bindings/phy/rcar-gen3-phy-usb2.txt
+++ b/dts/Bindings/phy/rcar-gen3-phy-usb2.txt
@@ -1,10 +1,12 @@
 * Renesas R-Car generation 3 USB 2.0 PHY
 
 This file provides information on what the device node for the R-Car generation
-3 USB 2.0 PHY contains.
+3 and RZ/G2 USB 2.0 PHY contain.
 
 Required properties:
-- compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795
+- compatible: "renesas,usb2-phy-r8a774a1" if the device is a part of an R8A774A1
+	      SoC.
+	      "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795
 	      SoC.
 	      "renesas,usb2-phy-r8a7796" if the device is a part of an R8A7796
 	      SoC.
@@ -14,7 +16,8 @@ Required properties:
 	      R8A77990 SoC.
 	      "renesas,usb2-phy-r8a77995" if the device is a part of an
 	      R8A77995 SoC.
-	      "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 compatible device.
+	      "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 or RZ/G2
+	      compatible device.
 
 	      When compatible with the generic version, nodes must list the
 	      SoC-specific version corresponding to the platform first
@@ -31,6 +34,8 @@ channel as USB OTG:
 - interrupts: interrupt specifier for the PHY.
 - vbus-supply: Phandle to a regulator that provides power to the VBUS. This
 	       regulator will be managed during the PHY power on/off sequence.
+- renesas,no-otg-pins: boolean, specify when a board does not provide proper
+		       otg pins.
 
 Example (R-Car H3):
 
diff --git a/dts/Bindings/phy/rcar-gen3-phy-usb3.txt b/dts/Bindings/phy/rcar-gen3-phy-usb3.txt
index 47dd296ece..9d9826609c 100644
--- a/dts/Bindings/phy/rcar-gen3-phy-usb3.txt
+++ b/dts/Bindings/phy/rcar-gen3-phy-usb3.txt
@@ -1,20 +1,22 @@
 * Renesas R-Car generation 3 USB 3.0 PHY
 
 This file provides information on what the device node for the R-Car generation
-3 USB 3.0 PHY contains.
+3 and RZ/G2 USB 3.0 PHY contain.
 If you want to enable spread spectrum clock (ssc), you should use USB_EXTAL
 instead of USB3_CLK. However, if you don't want to these features, you don't
 need this driver.
 
 Required properties:
-- compatible: "renesas,r8a7795-usb3-phy" if the device is a part of an R8A7795
+- compatible: "renesas,r8a774a1-usb3-phy" if the device is a part of an R8A774A1
+	      SoC.
+	      "renesas,r8a7795-usb3-phy" if the device is a part of an R8A7795
 	      SoC.
 	      "renesas,r8a7796-usb3-phy" if the device is a part of an R8A7796
 	      SoC.
 	      "renesas,r8a77965-usb3-phy" if the device is a part of an
 	      R8A77965 SoC.
-	      "renesas,rcar-gen3-usb3-phy" for a generic R-Car Gen3 compatible
-	      device.
+	      "renesas,rcar-gen3-usb3-phy" for a generic R-Car Gen3 or RZ/G2
+	      compatible device.
 
 	      When compatible with the generic version, nodes must list the
 	      SoC-specific version corresponding to the platform first
diff --git a/dts/Bindings/phy/uniphier-pcie-phy.txt b/dts/Bindings/phy/uniphier-pcie-phy.txt
new file mode 100644
index 0000000000..1889d3b89d
--- /dev/null
+++ b/dts/Bindings/phy/uniphier-pcie-phy.txt
@@ -0,0 +1,31 @@
+Socionext UniPhier PCIe PHY bindings
+
+This describes the devicetree bindings for PHY interface built into
+PCIe controller implemented on Socionext UniPhier SoCs.
+
+Required properties:
+- compatible: Should contain one of the following:
+    "socionext,uniphier-ld20-pcie-phy" - for LD20 PHY
+    "socionext,uniphier-pxs3-pcie-phy" - for PXs3 PHY
+- reg: Specifies offset and length of the register set for the device.
+- #phy-cells: Must be zero.
+- clocks: A phandle to the clock gate for PCIe glue layer including
+	this phy.
+- resets: A phandle to the reset line for PCIe glue layer including
+	this phy.
+
+Optional properties:
+- socionext,syscon: A phandle to system control to set configurations
+	for phy.
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties.
+
+Example:
+	pcie_phy: phy@66038000 {
+		compatible = "socionext,uniphier-ld20-pcie-phy";
+		reg = <0x66038000 0x4000>;
+		#phy-cells = <0>;
+		clocks = <&sys_clk 24>;
+		resets = <&sys_rst 24>;
+		socionext,syscon = <&soc_glue>;
+	};
diff --git a/dts/Bindings/phy/uniphier-usb2-phy.txt b/dts/Bindings/phy/uniphier-usb2-phy.txt
new file mode 100644
index 0000000000..b43b28250c
--- /dev/null
+++ b/dts/Bindings/phy/uniphier-usb2-phy.txt
@@ -0,0 +1,45 @@
+Socionext UniPhier USB2 PHY
+
+This describes the devicetree bindings for PHY interface built into
+USB2 controller implemented on Socionext UniPhier SoCs.
+
+Pro4 SoC has both USB2 and USB3 host controllers, however, this USB3
+controller doesn't include its own High-Speed PHY. This needs to specify
+USB2 PHY instead of USB3 HS-PHY.
+
+Required properties:
+- compatible: Should contain one of the following:
+    "socionext,uniphier-pro4-usb2-phy" - for Pro4 SoC
+    "socionext,uniphier-ld11-usb2-phy" - for LD11 SoC
+
+Sub-nodes:
+Each PHY should be represented as a sub-node.
+
+Sub-nodes required properties:
+- #phy-cells: Should be 0.
+- reg: The number of the PHY.
+
+Sub-nodes optional properties:
+- vbus-supply: A phandle to the regulator for USB VBUS.
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties.
+
+Example:
+	soc-glue@5f800000 {
+		...
+		usb-phy {
+			compatible = "socionext,uniphier-ld11-usb2-phy";
+			usb_phy0: phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+			...
+		};
+	};
+
+	usb@5a800100 {
+		compatible = "socionext,uniphier-ehci", "generic-ehci";
+		...
+		phy-names = "usb";
+		phys = <&usb_phy0>;
+	};
diff --git a/dts/Bindings/phy/uniphier-usb3-hsphy.txt b/dts/Bindings/phy/uniphier-usb3-hsphy.txt
new file mode 100644
index 0000000000..e8d8086a7a
--- /dev/null
+++ b/dts/Bindings/phy/uniphier-usb3-hsphy.txt
@@ -0,0 +1,69 @@
+Socionext UniPhier USB3 High-Speed (HS) PHY
+
+This describes the devicetree bindings for PHY interfaces built into
+USB3 controller implemented on Socionext UniPhier SoCs.
+Although the controller includes High-Speed PHY and Super-Speed PHY,
+this describes about High-Speed PHY.
+
+Required properties:
+- compatible: Should contain one of the following:
+    "socionext,uniphier-pro4-usb3-hsphy" - for Pro4 SoC
+    "socionext,uniphier-pxs2-usb3-hsphy" - for PXs2 SoC
+    "socionext,uniphier-ld20-usb3-hsphy" - for LD20 SoC
+    "socionext,uniphier-pxs3-usb3-hsphy" - for PXs3 SoC
+- reg: Specifies offset and length of the register set for the device.
+- #phy-cells: Should be 0.
+- clocks: A list of phandles to the clock gate for USB3 glue layer.
+	According to the clock-names, appropriate clocks are required.
+- clock-names: Should contain the following:
+    "gio", "link" - for Pro4 SoC
+    "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional.
+    "phy", "link" - for others
+- resets: A list of phandles to the reset control for USB3 glue layer.
+	According to the reset-names, appropriate resets are required.
+- reset-names: Should contain the following:
+    "gio", "link" - for Pro4 SoC
+    "phy", "link" - for others
+
+Optional properties:
+- vbus-supply: A phandle to the regulator for USB VBUS.
+- nvmem-cells: Phandles to nvmem cell that contains the trimming data.
+	Available only for HS-PHY implemented on LD20 and PXs3, and
+	if unspecified, default value is used.
+- nvmem-cell-names: Should be the following names, which correspond to
+	each nvmem-cells.
+	All of the 3 parameters associated with the following names are
+	required for each port, if any one is omitted, the trimming data
+	of the port will not be set at all.
+    "rterm", "sel_t", "hs_i" - Each cell name for phy parameters
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties.
+
+Example:
+
+	usb-glue@65b00000 {
+		compatible = "socionext,uniphier-ld20-dwc3-glue",
+			     "simple-mfd";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x65b00000 0x400>;
+
+		usb_vbus0: regulator {
+			...
+		};
+
+		usb_hsphy0: hs-phy@200 {
+			compatible = "socionext,uniphier-ld20-usb3-hsphy";
+			reg = <0x200 0x10>;
+			#phy-cells = <0>;
+			clock-names = "link", "phy";
+			clocks = <&sys_clk 14>, <&sys_clk 16>;
+			reset-names = "link", "phy";
+			resets = <&sys_rst 14>, <&sys_rst 16>;
+			vbus-supply = <&usb_vbus0>;
+			nvmem-cell-names = "rterm", "sel_t", "hs_i";
+			nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>,
+				      <&usb_hs_i0>;
+		};
+		...
+	};
diff --git a/dts/Bindings/phy/uniphier-usb3-ssphy.txt b/dts/Bindings/phy/uniphier-usb3-ssphy.txt
new file mode 100644
index 0000000000..490b815445
--- /dev/null
+++ b/dts/Bindings/phy/uniphier-usb3-ssphy.txt
@@ -0,0 +1,57 @@
+Socionext UniPhier USB3 Super-Speed (SS) PHY
+
+This describes the devicetree bindings for PHY interfaces built into
+USB3 controller implemented on Socionext UniPhier SoCs.
+Although the controller includes High-Speed PHY and Super-Speed PHY,
+this describes about Super-Speed PHY.
+
+Required properties:
+- compatible: Should contain one of the following:
+    "socionext,uniphier-pro4-usb3-ssphy" - for Pro4 SoC
+    "socionext,uniphier-pxs2-usb3-ssphy" - for PXs2 SoC
+    "socionext,uniphier-ld20-usb3-ssphy" - for LD20 SoC
+    "socionext,uniphier-pxs3-usb3-ssphy" - for PXs3 SoC
+- reg: Specifies offset and length of the register set for the device.
+- #phy-cells: Should be 0.
+- clocks: A list of phandles to the clock gate for USB3 glue layer.
+	According to the clock-names, appropriate clocks are required.
+- clock-names:
+    "gio", "link" - for Pro4 SoC
+    "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional.
+    "phy", "link" - for others
+- resets: A list of phandles to the reset control for USB3 glue layer.
+	According to the reset-names, appropriate resets are required.
+- reset-names:
+    "gio", "link" - for Pro4 SoC
+    "phy", "link" - for others
+
+Optional properties:
+- vbus-supply: A phandle to the regulator for USB VBUS.
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties.
+
+Example:
+
+	usb-glue@65b00000 {
+		compatible = "socionext,uniphier-ld20-dwc3-glue",
+			     "simple-mfd";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x65b00000 0x400>;
+
+		usb_vbus0: regulator {
+			...
+		};
+
+		usb_ssphy0: ss-phy@300 {
+			compatible = "socionext,uniphier-ld20-usb3-ssphy";
+			reg = <0x300 0x10>;
+			#phy-cells = <0>;
+			clock-names = "link", "phy";
+			clocks = <&sys_clk 14>, <&sys_clk 16>;
+			reset-names = "link", "phy";
+			resets = <&sys_rst 14>, <&sys_rst 16>;
+			vbus-supply = <&usb_vbus0>;
+		};
+		...
+	};