dts: update to v4.6-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

6 files changed, 316 insertions, 1 deletions

diff --git a/dts/Bindings/regulator/act8945a-regulator.txt b/dts/Bindings/regulator/act8945a-regulator.txt
new file mode 100644
index 0000000000..5c80a77795
--- /dev/null
+++ b/dts/Bindings/regulator/act8945a-regulator.txt
@@ -0,0 +1,80 @@
+Device-Tree bindings for regulators of Active-semi ACT8945A Multi-Function Device
+
+Required properties:
+ - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt.
+
+Optional properties:
+- active-semi,vsel-high: Indicates if the VSEL pin is set to logic-high.
+  If this property is missing, assume the VSEL pin is set to logic-low.
+
+Optional input supply properties:
+  - vp1-supply: The input supply for REG_DCDC1
+  - vp2-supply: The input supply for REG_DCDC2
+  - vp3-supply: The input supply for REG_DCDC3
+  - inl45-supply: The input supply for REG_LDO1 and REG_LDO2
+  - inl67-supply: The input supply for REG_LDO3 and REG_LDO4
+
+Any standard regulator properties can be used to configure the single regulator.
+
+The valid names for regulators are:
+	REG_DCDC1, REG_DCDC2, REG_DCDC3, REG_LDO1, REG_LDO2, REG_LDO3, REG_LDO4.
+
+Example:
+	pmic@5b {
+		compatible = "active-semi,act8945a";
+		reg = <0x5b>;
+		status = "okay";
+
+		active-semi,vsel-high;
+
+		regulators {
+			vdd_1v35_reg: REG_DCDC1 {
+				regulator-name = "VDD_1V35";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+			};
+
+			vdd_1v2_reg: REG_DCDC2 {
+				regulator-name = "VDD_1V2";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+			};
+
+			vdd_3v3_reg: REG_DCDC3 {
+				regulator-name = "VDD_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_fuse_reg: REG_LDO1 {
+				regulator-name = "VDD_FUSE";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-always-on;
+			};
+
+			vdd_3v3_lp_reg: REG_LDO2 {
+				regulator-name = "VDD_3V3_LP";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_led_reg: REG_LDO3 {
+				regulator-name = "VDD_LED";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_sdhc_1v8_reg: REG_LDO4 {
+				regulator-name = "VDD_SDHC_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
+	};
diff --git a/dts/Bindings/regulator/hisilicon,hi655x-regulator.txt b/dts/Bindings/regulator/hisilicon,hi655x-regulator.txt
new file mode 100644
index 0000000000..14cfdc5641
--- /dev/null
+++ b/dts/Bindings/regulator/hisilicon,hi655x-regulator.txt
@@ -0,0 +1,29 @@
+Hisilicon Hi655x Voltage regulators
+
+Note:
+The Hi655x regulator control is managed by Hi655x PMIC.
+So the node of this regulator must be child node of Hi655x
+PMIC node.
+
+The driver uses the regulator core framework, so please also
+take the bindings of regulator.txt for reference.
+
+The valid names for regulators are:
+
+LDO2_2V8 LDO7_SDIO LDO10_2V85 LDO13_1V8 LDO14_2V8
+LDO15_1V8 LDO17_2V5 LDO19_3V0 LDO21_1V8 LDO22_1V2
+
+Example:
+        pmic: pmic@f8000000 {
+                compatible = "hisilicon,hi655x-pmic";
+		...
+		regulators {
+			ldo2: LDO2@a21 {
+				regulator-name = "LDO2_2V8";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3200000>;
+				regulator-enable-ramp-delay = <120>;
+			};
+			...
+		}
+	}
diff --git a/dts/Bindings/regulator/lp872x.txt b/dts/Bindings/regulator/lp872x.txt
index 78183182da..ca58a68ffd 100644
--- a/dts/Bindings/regulator/lp872x.txt
+++ b/dts/Bindings/regulator/lp872x.txt
@@ -28,6 +28,7 @@ Optional properties:
   - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices.
   - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2.
   - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH.
+  - enable-gpios: GPIO specifier for EN pin control of LP872x devices.
 
   Sub nodes for regulator_init_data
     LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck)
diff --git a/dts/Bindings/regulator/max77802.txt b/dts/Bindings/regulator/max77802.txt
index 09d796ed48..879e98d3b9 100644
--- a/dts/Bindings/regulator/max77802.txt
+++ b/dts/Bindings/regulator/max77802.txt
@@ -60,7 +60,7 @@ The possible values for "regulator-initial-mode" and "regulator-mode" are:
 	1: Normal regulator voltage output mode.
 	3: Low Power which reduces the quiescent current down to only 1uA
 
-The list of valid modes are defined in the dt-bindings/clock/maxim,max77802.h
+The valid modes list is defined in the dt-bindings/regulator/maxim,max77802.h
 header and can be included by device tree source files.
 
 The standard "regulator-mode" property can only be used for regulators that
diff --git a/dts/Bindings/regulator/regulator-max77620.txt b/dts/Bindings/regulator/regulator-max77620.txt
new file mode 100644
index 0000000000..b3c8ca6720
--- /dev/null
+++ b/dts/Bindings/regulator/regulator-max77620.txt
@@ -0,0 +1,200 @@
+Regulator DT binding for MAX77620 Power management IC from Maxim Semiconductor.
+
+Device has multiple DCDC(sd[0-3] and LDOs(ldo[0-8]). The input supply
+of these regulators are defined under parent device node.
+Details of regulator properties are defined as child node under
+sub-node "regulators" which is child node of device node.
+
+Please refer file <Documentation/devicetree/bindings/regulator/regulator.txt>
+for common regulator bindings used by client.
+
+Following are properties of parent node related to regulators.
+
+Optional properties:
+-------------------
+The input supply of regulators are the optional properties on the
+parent device node. The input supply of these regulators are provided
+through following properties:
+in-sd0-supply:		Input supply for SD0, INA-SD0 or INB-SD0 pins.
+in-sd1-supply:		Input supply for SD1.
+in-sd2-supply:		Input supply for SD2.
+in-sd3-supply:		Input supply for SD3.
+in-ldo0-1-supply:	Input supply for LDO0 and LDO1.
+in-ldo2-supply:		Input supply for LDO2.
+in-ldo3-5-supply:	Input supply for LDO3 and LDO5
+in-ldo4-6-supply:	Input supply for LDO4 and LDO6.
+in-ldo7-8-supply:	Input supply for LDO7 and LDO8.
+
+Optional sub nodes for regulators under "regulators" subnode:
+------------------------------------------------------------
+The subnodes name is the name of regulator and it must be one of:
+	sd[0-3], ldo[0-8]
+
+Each sub-node should contain the constraints and initialization
+information for that regulator. The definition for each of these
+nodes is defined using the standard binding for regulators found at
+<Documentation/devicetree/bindings/regulator/regulator.txt>.
+
+Theres are also additional properties for SD/LDOs. These additional properties
+are required to configure FPS configuration parameters for SDs and LDOs.
+Please refer <devicetree/bindings/mfd/max77620.txt> for more detail of Flexible
+Power Sequence (FPS).
+Following are additional properties:
+
+- maxim,active-fps-source:		FPS source for the regulators to get
+					enabled/disabled when system is in
+					active state.  Valid values are:
+					- MAX77620_FPS_SRC_0,
+						FPS source is FPS0.
+					- MAX77620_FPS_SRC_1,
+						FPS source is FPS1
+					- MAX77620_FPS_SRC_2 and
+						FPS source is FPS2
+					- MAX77620_FPS_SRC_NONE.
+						Regulator is not controlled
+						by FPS events and it gets
+						enabled/disabled by register
+						access.
+					Absence of this property will leave
+					the FPS configuration register for that
+					regulator to default configuration.
+
+- maxim,active-fps-power-up-slot:	Sequencing event slot number on which
+					the regulator get enabled when
+					master FPS input event set to HIGH.
+					Valid values are 0 to 7.
+					This is applicable if FPS source is
+					selected as FPS0, FPS1 or FPS2.
+			
+- maxim,active-fps-power-down-slot:	Sequencing event slot number on which
+					the regulator get disabled when master
+					FPS input event set to LOW.
+					Valid values are 0 to 7.
+					This is applicable if FPS source is
+					selected as FPS0, FPS1 or FPS2.
+			
+- maxim,suspend-fps-source:		This is same as property
+					"maxim,active-fps-source" but value
+					get configured when system enters in
+					to suspend state.
+
+- maxim,suspend-fps-power-up-slot:	This is same as property
+					"maxim,active-fps-power-up-slot" but
+					this value get configured into FPS
+					configuration register when system
+					enters into suspend.
+					This is applicable if suspend state
+					FPS source is selected as FPS0, FPS1 or
+
+- maxim,suspend-fps-power-down-slot:	This is same as property
+					"maxim,active-fps-power-down-slot" but
+					this value get configured into FPS
+					configuration register when system
+					enters into suspend.
+					This is applicable if suspend state
+					FPS source is selected as FPS0, FPS1 or
+					FPS2.
+
+Example:
+--------
+#include <dt-bindings/mfd/max77620.h>
+...
+max77620@3c {
+	in-ldo0-1-supply = <&max77620_sd2>;
+	in-ldo7-8-supply = <&max77620_sd2>;
+	regulators {
+		sd0 {
+			regulator-name = "vdd-core";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1400000>;
+			regulator-boot-on;
+			regulator-always-on;
+			maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+		};
+
+		sd1 {
+			regulator-name = "vddio-ddr";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-always-on;
+			regulator-boot-on;
+			maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+		};
+
+		sd2 {
+			regulator-name = "vdd-pre-reg";
+			regulator-min-microvolt = <1350000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		sd3 {
+			regulator-name = "vdd-1v8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		ldo0 {
+			regulator-name = "avdd-sys";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		ldo1 {
+			regulator-name = "vdd-pex";
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		ldo2 {
+			regulator-name = "vddio-sdmmc3";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		ldo3 {
+			regulator-name = "vdd-cam-hv";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		ldo4 {
+			regulator-name = "vdd-rtc";
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		ldo5 {
+			regulator-name = "avdd-ts-hv";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		ldo6 {
+			regulator-name = "vdd-ts";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		ldo7 {
+			regulator-name = "vdd-gen-pll-edp";
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		ldo8 {
+			regulator-name = "vdd-hdmi-dp";
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+};
diff --git a/dts/Bindings/regulator/regulator.txt b/dts/Bindings/regulator/regulator.txt
index 1d112fc456..ecfc593cac 100644
--- a/dts/Bindings/regulator/regulator.txt
+++ b/dts/Bindings/regulator/regulator.txt
@@ -44,6 +44,11 @@ Optional properties:
   any consumer request.
 - regulator-pull-down: Enable pull down resistor when the regulator is disabled.
 - regulator-over-current-protection: Enable over current protection.
+- regulator-active-discharge: tristate, enable/disable active discharge of
+  regulators. The values are:
+	0: Disable active discharge.
+	1: Enable active discharge.
+	Absence of this property will leave configuration to default.
 
 Deprecated properties:
 - regulator-compatible: If a regulator chip contains multiple