dts: update to v5.9-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

7 files changed, 1272 insertions, 123 deletions

diff --git a/dts/src/mips/ingenic/cu1000-neo.dts b/dts/src/mips/ingenic/cu1000-neo.dts
index 03abd94acd..22a1066d63 100644
--- a/dts/src/mips/ingenic/cu1000-neo.dts
+++ b/dts/src/mips/ingenic/cu1000-neo.dts
@@ -7,8 +7,8 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
-	compatible = "yna,cu1000-neo", "ingenic,x1000";
-	model = "YSH & ATIL General Board CU Neo";
+	compatible = "yna,cu1000-neo", "ingenic,x1000e";
+	model = "YSH & ATIL General Board CU1000-Neo";
 
 	aliases {
 		serial2 = &uart2;
@@ -23,20 +23,19 @@
 		reg = <0x0 0x04000000>;
 	};
 
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			gpios = <&gpb 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+		};
+	};
+
 	wlan_pwrseq: msc1-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 
-		clocks = <&lpoclk>;
-		clock-names = "ext_clock";
-
 		reset-gpios = <&gpc 17 GPIO_ACTIVE_LOW>;
 		post-power-on-delay-ms = <200>;
-
-		lpoclk: ap6212a {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
 	};
 };
 
@@ -53,6 +52,13 @@
 	ingenic,pwm-channels-mask = <0xfa>;
 };
 
+&uart2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart2>;
+};
+
 &i2c0 {
 	status = "okay";
 
@@ -61,43 +67,15 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pins_i2c0>;
 
-	ads7830@48 {
+	ads7830: adc@48 {
 		compatible = "ti,ads7830";
 		reg = <0x48>;
 	};
 };
 
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pins_uart2>;
-
-	status = "okay";
-};
-
-&mac {
-	phy-mode = "rmii";
-	phy-handle = <&lan8720a>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pins_mac>;
-
-	snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
-	snps,reset-active-low;
-	snps,reset-delays-us = <0 10000 30000>;
-
-	status = "okay";
-};
-
-&mdio {
+&msc0 {
 	status = "okay";
 
-	lan8720a: ethernet-phy@0 {
-		compatible = "ethernet-phy-id0007.c0f0", "ethernet-phy-ieee802.3-c22";
-		reg = <0>;
-	};
-};
-
-&msc0 {
 	bus-width = <8>;
 	max-frequency = <50000000>;
 
@@ -105,26 +83,23 @@
 	pinctrl-0 = <&pins_msc0>;
 
 	non-removable;
-
-	status = "okay";
 };
 
 &msc1 {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
 	bus-width = <4>;
 	max-frequency = <50000000>;
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&pins_msc1>;
 
-	#address-cells = <1>;
-	#size-cells = <0>;
-
 	non-removable;
 
 	mmc-pwrseq = <&wlan_pwrseq>;
 
-	status = "okay";
-
 	ap6212a: wifi@1 {
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
@@ -137,23 +112,40 @@
 	};
 };
 
-&pinctrl {
-	pins_i2c0: i2c0 {
-		function = "i2c0";
-		groups = "i2c0-data";
-		bias-disable;
+&mac {
+	status = "okay";
+
+	phy-mode = "rmii";
+	phy-handle = <&lan8720a>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mac>;
+
+	snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 30000>;
+};
+
+&mdio {
+	status = "okay";
+
+	lan8720a: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0007.c0f0", "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
 	};
+};
 
+&pinctrl {
 	pins_uart2: uart2 {
 		function = "uart2";
 		groups = "uart2-data-d";
-		bias-disable;
+		bias-pull-up;
 	};
 
-	pins_mac: mac {
-		function = "mac";
-		groups = "mac";
-		bias-disable;
+	pins_i2c0: i2c0 {
+		function = "i2c0";
+		groups = "i2c0-data";
+		bias-pull-up;
 	};
 
 	pins_msc0: msc0 {
@@ -167,4 +159,10 @@
 		groups = "mmc1-1bit", "mmc1-4bit";
 		bias-disable;
 	};
+
+	pins_mac: mac {
+		function = "mac";
+		groups = "mac";
+		bias-disable;
+	};
 };
diff --git a/dts/src/mips/ingenic/cu1830-neo.dts b/dts/src/mips/ingenic/cu1830-neo.dts
new file mode 100644
index 0000000000..640f96c00d
--- /dev/null
+++ b/dts/src/mips/ingenic/cu1830-neo.dts
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "x1830.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "yna,cu1830-neo", "ingenic,x1830";
+	model = "YSH & ATIL General Board CU1830-Neo";
+
+	aliases {
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			gpios = <&gpc 17 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+		};
+	};
+
+	wlan_pwrseq: msc1-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		reset-gpios = <&gpc 13 GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&exclk {
+	clock-frequency = <24000000>;
+};
+
+&tcu {
+	/* 1500 kHz for the system timer and clocksource */
+	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
+	assigned-clock-rates = <1500000>, <1500000>;
+
+	/* Use channel #0 for the system timer channel #2 for the clocksource */
+	ingenic,pwm-channels-mask = <0xfa>;
+};
+
+&uart1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart1>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_i2c0>;
+
+	ads7830: adc@48 {
+		compatible = "ti,ads7830";
+		reg = <0x48>;
+	};
+};
+
+&msc0 {
+	status = "okay";
+
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_msc0>;
+
+	non-removable;
+};
+
+&msc1 {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_msc1>;
+
+	non-removable;
+
+	mmc-pwrseq = <&wlan_pwrseq>;
+
+	ap6212a: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupt-parent = <&gpc>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		brcm,drive-strength = <10>;
+	};
+};
+
+&mac {
+	status = "okay";
+
+	phy-mode = "rmii";
+	phy-handle = <&ip101gr>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mac>;
+
+	snps,reset-gpio = <&gpb 28 GPIO_ACTIVE_LOW>; /* PB28 */
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 30000>;
+};
+
+&mdio {
+	status = "okay";
+
+	ip101gr: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0243.0c54", "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&pinctrl {
+	pins_uart1: uart1 {
+		function = "uart1";
+		groups = "uart1-data";
+		bias-pull-up;
+	};
+
+	pins_i2c0: i2c0 {
+		function = "i2c0";
+		groups = "i2c0-data";
+		bias-pull-up;
+	};
+
+	pins_msc0: msc0 {
+		function = "mmc0";
+		groups = "mmc0-1bit", "mmc0-4bit";
+		bias-disable;
+	};
+
+	pins_msc1: msc1 {
+		function = "mmc1";
+		groups = "mmc1-1bit", "mmc1-4bit";
+		bias-disable;
+	};
+
+	pins_mac: mac {
+		function = "mac";
+		groups = "mac";
+		bias-disable;
+	};
+};
diff --git a/dts/src/mips/ingenic/jz4725b.dtsi b/dts/src/mips/ingenic/jz4725b.dtsi
new file mode 100644
index 0000000000..a8fca56087
--- /dev/null
+++ b/dts/src/mips/ingenic/jz4725b.dtsi
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/jz4725b-cgu.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ingenic,jz4725b";
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	intc: interrupt-controller@10001000 {
+		compatible = "ingenic,jz4725b-intc", "ingenic,jz4740-intc";
+		reg = <0x10001000 0x14>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <2>;
+	};
+
+	ext: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	osc32k: osc32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	cgu: clock-controller@10000000 {
+		compatible = "ingenic,jz4725b-cgu";
+		reg = <0x10000000 0x100>;
+
+		clocks = <&ext>, <&osc32k>;
+		clock-names = "ext", "osc32k";
+
+		#clock-cells = <1>;
+	};
+
+	tcu: timer@10002000 {
+		compatible = "ingenic,jz4725b-tcu", "simple-mfd";
+		reg = <0x10002000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10002000 0x1000>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu JZ4725B_CLK_RTC>,
+			 <&cgu JZ4725B_CLK_EXT>,
+			 <&cgu JZ4725B_CLK_PCLK>,
+			 <&cgu JZ4725B_CLK_TCU>;
+		clock-names = "rtc", "ext", "pclk", "tcu";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <23>, <22>, <21>;
+
+		watchdog: watchdog@0 {
+			compatible = "ingenic,jz4725b-watchdog", "ingenic,jz4740-watchdog";
+			reg = <0x0 0xc>;
+
+			clocks = <&tcu TCU_CLK_WDT>;
+			clock-names = "wdt";
+		};
+
+		pwm: pwm@60 {
+			compatible = "ingenic,jz4725b-pwm";
+			reg = <0x60 0x40>;
+
+			#pwm-cells = <3>;
+
+			clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>,
+				 <&tcu TCU_CLK_TIMER2>, <&tcu TCU_CLK_TIMER3>,
+				 <&tcu TCU_CLK_TIMER4>, <&tcu TCU_CLK_TIMER5>;
+			clock-names = "timer0", "timer1", "timer2",
+				      "timer3", "timer4", "timer5";
+		};
+
+		ost: timer@e0 {
+			compatible = "ingenic,jz4725b-ost";
+			reg = <0xe0 0x20>;
+
+			clocks = <&tcu TCU_CLK_OST>;
+			clock-names = "ost";
+
+			interrupts = <15>;
+		};
+	};
+
+	rtc_dev: rtc@10003000 {
+		compatible = "ingenic,jz4725b-rtc", "ingenic,jz4740-rtc";
+		reg = <0x10003000 0x40>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <6>;
+
+		clocks = <&cgu JZ4725B_CLK_RTC>;
+		clock-names = "rtc";
+	};
+
+	pinctrl: pinctrl@10010000 {
+		compatible = "ingenic,jz4725b-pinctrl";
+		reg = <0x10010000 0x400>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpa: gpio@0 {
+			compatible = "ingenic,jz4725b-gpio";
+			reg = <0>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <16>;
+		};
+
+		gpb: gpio@1 {
+			compatible = "ingenic,jz4725b-gpio";
+			reg = <1>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 32 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <15>;
+		};
+
+		gpc: gpio@2 {
+			compatible = "ingenic,jz4725b-gpio";
+			reg = <2>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 64 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <14>;
+		};
+
+		gpd: gpio@3 {
+			compatible = "ingenic,jz4725b-gpio";
+			reg = <3>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 96 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <13>;
+		};
+	};
+
+	aic: audio-controller@10020000 {
+		compatible = "ingenic,jz4725b-i2s", "ingenic,jz4740-i2s";
+		reg = <0x10020000 0x38>;
+
+		#sound-dai-cells = <0>;
+
+		clocks = <&cgu JZ4725B_CLK_AIC>,
+			 <&cgu JZ4725B_CLK_I2S>,
+			 <&cgu JZ4725B_CLK_EXT>,
+			 <&cgu JZ4725B_CLK_PLL_HALF>;
+		clock-names = "aic", "i2s", "ext", "pll half";
+
+		interrupt-parent = <&intc>;
+		interrupts = <10>;
+
+		dmas = <&dmac 25 0xffffffff>, <&dmac 24 0xffffffff>;
+		dma-names = "rx", "tx";
+	};
+
+	codec: audio-codec@100200a4 {
+		compatible = "ingenic,jz4725b-codec";
+		reg = <0x100200a4 0x8>;
+
+		#sound-dai-cells = <0>;
+
+		clocks = <&cgu JZ4725B_CLK_AIC>;
+		clock-names = "aic";
+	};
+
+	mmc0: mmc@10021000 {
+		compatible = "ingenic,jz4725b-mmc";
+		reg = <0x10021000 0x1000>;
+
+		clocks = <&cgu JZ4725B_CLK_MMC0>;
+		clock-names = "mmc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <25>;
+
+		dmas = <&dmac 27 0xffffffff>, <&dmac 26 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+	};
+
+	mmc1: mmc@10022000 {
+		compatible = "ingenic,jz4725b-mmc";
+		reg = <0x10022000 0x1000>;
+
+		clocks = <&cgu JZ4725B_CLK_MMC1>;
+		clock-names = "mmc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <24>;
+
+		dmas = <&dmac 31 0xffffffff>, <&dmac 30 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+	};
+
+	uart: serial@10030000 {
+		compatible = "ingenic,jz4725b-uart", "ingenic,jz4740-uart";
+		reg = <0x10030000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <9>;
+
+		clocks = <&ext>, <&cgu JZ4725B_CLK_UART>;
+		clock-names = "baud", "module";
+	};
+
+	adc: adc@10070000 {
+		compatible = "ingenic,jz4725b-adc";
+		#io-channel-cells = <1>;
+
+		reg = <0x10070000 0x30>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10070000 0x30>;
+
+		clocks = <&cgu JZ4725B_CLK_ADC>;
+		clock-names = "adc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <18>;
+	};
+
+	nemc: memory-controller@13010000 {
+		compatible = "ingenic,jz4725b-nemc", "ingenic,jz4740-nemc";
+		reg = <0x13010000 0x10000>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <1 0 0x18000000 0x4000000>, <2 0 0x14000000 0x4000000>,
+			 <3 0 0x0c000000 0x4000000>, <4 0 0x08000000 0x4000000>;
+
+		clocks = <&cgu JZ4725B_CLK_MCLK>;
+	};
+
+	dmac: dma-controller@13020000 {
+		compatible = "ingenic,jz4725b-dma";
+		reg = <0x13020000 0xd8>, <0x13020300 0x14>;
+
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <29>;
+
+		clocks = <&cgu JZ4725B_CLK_DMA>;
+	};
+
+	udc: usb@13040000 {
+		compatible = "ingenic,jz4725b-musb", "ingenic,jz4740-musb";
+		reg = <0x13040000 0x10000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <27>;
+		interrupt-names = "mc";
+
+		clocks = <&cgu JZ4725B_CLK_UDC>;
+		clock-names = "udc";
+	};
+
+	lcd: lcd-controller@13050000 {
+		compatible = "ingenic,jz4725b-lcd";
+		reg = <0x13050000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <31>;
+
+		clocks = <&cgu JZ4725B_CLK_LCD>;
+		clock-names = "lcd_pclk";
+
+		lcd_ports: ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@8 {
+				reg = <8>;
+
+				ipu_output: endpoint {
+					remote-endpoint = <&ipu_input>;
+				};
+			};
+		};
+	};
+
+	ipu: ipu@13080000 {
+		compatible = "ingenic,jz4725b-ipu";
+		reg = <0x13080000 0x64>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <30>;
+
+		clocks = <&cgu JZ4725B_CLK_IPU>;
+		clock-names = "ipu";
+
+		port {
+			ipu_input: endpoint {
+				remote-endpoint = <&ipu_output>;
+			};
+		};
+	};
+
+	bch: ecc-controller@130d0000 {
+		compatible = "ingenic,jz4725b-bch";
+		reg = <0x130d0000 0x44>;
+
+		clocks = <&cgu JZ4725B_CLK_BCH>;
+	};
+
+	rom: memory@1fc00000 {
+		compatible = "mtd-rom";
+		probe-type = "map_rom";
+		reg = <0x1fc00000 0x2000>;
+
+		bank-width = <4>;
+		device-width = <1>;
+	};
+};
diff --git a/dts/src/mips/ingenic/qi_lb60.dts b/dts/src/mips/ingenic/qi_lb60.dts
index 7a371d9c5a..bf298268f1 100644
--- a/dts/src/mips/ingenic/qi_lb60.dts
+++ b/dts/src/mips/ingenic/qi_lb60.dts
@@ -16,6 +16,12 @@
 
 / {
 	compatible = "qi,lb60", "ingenic,jz4740";
+	model = "Ben Nanonote";
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x2000000>;
+	};
 
 	chosen {
 		stdout-path = &uart0;
@@ -69,7 +75,7 @@
 			"Speaker", "OUTL",
 			"Speaker", "OUTR",
 			"INL", "LOUT",
-			"INL", "ROUT";
+			"INR", "ROUT";
 
 		simple-audio-card,aux-devs = <&amp>;
 
diff --git a/dts/src/mips/ingenic/rs90.dts b/dts/src/mips/ingenic/rs90.dts
new file mode 100644
index 0000000000..4eb1edbfc1
--- /dev/null
+++ b/dts/src/mips/ingenic/rs90.dts
@@ -0,0 +1,315 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "jz4725b.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/iio/adc/ingenic,adc.h>
+#include <dt-bindings/input/linux-event-codes.h>
+
+/ {
+	compatible = "ylm,rs90", "ingenic,jz4725b";
+	model = "RS-90";
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x2000000>;
+	};
+
+	vcc: regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vcc";
+		regulaor-min-microvolt = <3300000>;
+		regulaor-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 40000 0>;
+
+		brightness-levels = <0 16 32 48 64 80 112 144 192 255>;
+		default-brightness-level = <8>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_pwm3>;
+
+		power-supply = <&vcc>;
+	};
+
+	keys@0 {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		key@0 {
+			label = "D-pad up";
+			linux,code = <KEY_UP>;
+			gpios = <&gpc 10 GPIO_ACTIVE_LOW>;
+		};
+
+		key@1 {
+			label = "D-pad down";
+			linux,code = <KEY_DOWN>;
+			gpios = <&gpc 11 GPIO_ACTIVE_LOW>;
+		};
+
+		key@2 {
+			label = "D-pad left";
+			linux,code = <KEY_LEFT>;
+			gpios = <&gpb 31 GPIO_ACTIVE_LOW>;
+		};
+
+		key@3 {
+			label = "D-pad right";
+			linux,code = <KEY_RIGHT>;
+			gpios = <&gpd 21 GPIO_ACTIVE_LOW>;
+		};
+
+		key@4 {
+			label = "Button A";
+			linux,code = <KEY_LEFTCTRL>;
+			gpios = <&gpc 31 GPIO_ACTIVE_LOW>;
+		};
+
+		key@5 {
+			label = "Button B";
+			linux,code = <KEY_LEFTALT>;
+			gpios = <&gpc 30 GPIO_ACTIVE_LOW>;
+		};
+
+		key@6 {
+			label = "Right shoulder button";
+			linux,code = <KEY_BACKSPACE>;
+			gpios = <&gpc 12 GPIO_ACTIVE_LOW>;
+			debounce-interval = <10>;
+		};
+
+		key@7 {
+			label = "Start button";
+			linux,code = <KEY_ENTER>;
+			gpios = <&gpd 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keys@1 {
+		compatible = "adc-keys";
+		io-channels = <&adc INGENIC_ADC_AUX>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1400000>;
+		poll-interval = <30>;
+
+		key@0 {
+			label = "Left shoulder button";
+			linux,code = <KEY_TAB>;
+			press-threshold-microvolt = <800000>;
+		};
+
+		key@1 {
+			label = "Select button";
+			linux,code = <KEY_ESC>;
+			press-threshold-microvolt = <1100000>;
+		};
+	};
+
+	amp: analog-amplifier {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&gpc 15 GPIO_ACTIVE_HIGH>;
+
+		VCC-supply = <&vcc>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+
+		simple-audio-card,name = "rs90-audio";
+		simple-audio-card,format = "i2s";
+
+		simple-audio-card,widgets =
+			"Speaker", "Speaker",
+			"Headphone", "Headphones";
+		simple-audio-card,routing =
+			"INL", "LHPOUT",
+			"INR", "RHPOUT",
+			"Headphones", "LHPOUT",
+			"Headphones", "RHPOUT",
+			"Speaker", "OUTL",
+			"Speaker", "OUTR";
+		simple-audio-card,pin-switches = "Speaker";
+
+		simple-audio-card,hp-det-gpio = <&gpd 16 GPIO_ACTIVE_LOW>;
+		simple-audio-card,aux-devs = <&amp>;
+
+		simple-audio-card,bitclock-master = <&dai_codec>;
+		simple-audio-card,frame-master = <&dai_codec>;
+
+		dai_cpu: simple-audio-card,cpu {
+			sound-dai = <&aic>;
+		};
+
+		dai_codec: simple-audio-card,codec {
+			sound-dai = <&codec>;
+		};
+
+	};
+
+	usb_phy: usb-phy {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+
+		clocks = <&cgu JZ4725B_CLK_UDC_PHY>;
+		clock-names = "main_clk";
+		vcc-supply = <&vcc>;
+	};
+
+	panel {
+		compatible = "sharp,ls020b1dd01d";
+
+		backlight = <&backlight>;
+		power-supply = <&vcc>;
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&panel_output>;
+			};
+		};
+	};
+};
+
+&ext {
+	clock-frequency = <12000000>;
+};
+
+&rtc_dev {
+	system-power-controller;
+};
+
+&udc {
+	phys = <&usb_phy>;
+};
+
+&pinctrl {
+	pins_mmc1: mmc1 {
+		function = "mmc1";
+		groups = "mmc1-1bit";
+	};
+
+	pins_nemc: nemc {
+		function = "nand";
+		groups = "nand-cs1", "nand-cle-ale", "nand-fre-fwe";
+	};
+
+	pins_pwm3: pwm3 {
+		function = "pwm3";
+		groups = "pwm3";
+		bias-disable;
+	};
+
+	pins_lcd: lcd {
+		function = "lcd";
+		groups = "lcd-8bit", "lcd-16bit", "lcd-special";
+	};
+};
+
+&mmc0 {
+	status = "disabled";
+};
+
+&mmc1 {
+	bus-width = <1>;
+	max-frequency = <48000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mmc1>;
+
+	cd-gpios = <&gpc 20 GPIO_ACTIVE_LOW>;
+};
+
+&uart {
+	/*
+	 * The pins for RX/TX are used for the right shoulder button and
+	 * backlight PWM.
+	 */
+	status = "disabled";
+};
+
+&nemc {
+	nandc: nand-controller@1 {
+		compatible = "ingenic,jz4725b-nand";
+		reg = <1 0 0x4000000>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ecc-engine = <&bch>;
+
+		ingenic,nemc-tAS = <10>;
+		ingenic,nemc-tAH = <5>;
+		ingenic,nemc-tBP = <10>;
+		ingenic,nemc-tAW = <15>;
+		ingenic,nemc-tSTRV = <100>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_nemc>;
+
+		rb-gpios = <&gpc 27 GPIO_ACTIVE_HIGH>;
+
+		nand@1 {
+			reg = <1>;
+
+			nand-ecc-step-size = <512>;
+			nand-ecc-strength = <8>;
+			nand-ecc-mode = "hw";
+			nand-is-boot-medium;
+			nand-on-flash-bbt;
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "bootloader";
+					reg = <0x0 0x20000>;
+				};
+
+				partition@20000 {
+					label = "system";
+					reg = <0x20000 0x0>;
+				};
+			};
+		};
+	};
+};
+
+&cgu {
+	/* Use 32kHz oscillator as the parent of the RTC clock */
+	assigned-clocks = <&cgu JZ4725B_CLK_RTC>;
+	assigned-clock-parents = <&cgu JZ4725B_CLK_OSC32K>;
+};
+
+&tcu {
+	/*
+	 * 750 kHz for the system timer and clocksource, and use RTC as the
+	 * parent for the watchdog clock.
+	 */
+	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>, <&tcu TCU_CLK_WDT>;
+	assigned-clock-parents = <0>, <0>, <&cgu JZ4725B_CLK_RTC>;
+	assigned-clock-rates = <750000>, <750000>;
+};
+
+&lcd {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_lcd>;
+};
+
+&lcd_ports {
+	port@0 {
+		reg = <0>;
+
+		panel_output: endpoint {
+			remote-endpoint = <&panel_input>;
+		};
+	};
+};
diff --git a/dts/src/mips/ingenic/x1000.dtsi b/dts/src/mips/ingenic/x1000.dtsi
index 59a63a0985..9de9e7c2d5 100644
--- a/dts/src/mips/ingenic/x1000.dtsi
+++ b/dts/src/mips/ingenic/x1000.dtsi
@@ -48,9 +48,7 @@
 	};
 
 	tcu: timer@10002000 {
-		compatible = "ingenic,x1000-tcu",
-				 "ingenic,jz4770-tcu",
-				 "simple-mfd";
+		compatible = "ingenic,x1000-tcu", "simple-mfd";
 		reg = <0x10002000 0x1000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -156,48 +154,6 @@
 		};
 	};
 
-	i2c0: i2c-controller@10050000 {
-		compatible = "ingenic,x1000-i2c";
-		reg = <0x10050000 0x1000>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		interrupt-parent = <&intc>;
-		interrupts = <60>;
-
-		clocks = <&cgu X1000_CLK_I2C0>;
-
-		status = "disabled";
-	};
-
-	i2c1: i2c-controller@10051000 {
-		compatible = "ingenic,x1000-i2c";
-		reg = <0x10051000 0x1000>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		interrupt-parent = <&intc>;
-		interrupts = <59>;
-
-		clocks = <&cgu X1000_CLK_I2C1>;
-
-		status = "disabled";
-	};
-
-	i2c2: i2c-controller@10052000 {
-		compatible = "ingenic,x1000-i2c";
-		reg = <0x10052000 0x1000>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		interrupt-parent = <&intc>;
-		interrupts = <58>;
-
-		clocks = <&cgu X1000_CLK_I2C2>;
-
-		status = "disabled";
-	};
-
 	uart0: serial@10030000 {
 		compatible = "ingenic,x1000-uart";
 		reg = <0x10030000 0x100>;
@@ -237,37 +193,57 @@
 		status = "disabled";
 	};
 
-	pdma: dma-controller@13420000 {
-		compatible = "ingenic,x1000-dma";
-		reg = <0x13420000 0x400>, <0x13421000 0x40>;
-		#dma-cells = <2>;
+	i2c0: i2c-controller@10050000 {
+		compatible = "ingenic,x1000-i2c";
+		reg = <0x10050000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
 		interrupt-parent = <&intc>;
-		interrupts = <10>;
+		interrupts = <60>;
 
-		clocks = <&cgu X1000_CLK_PDMA>;
+		clocks = <&cgu X1000_CLK_I2C0>;
+
+		status = "disabled";
 	};
 
-	mac: ethernet@134b0000 {
-		compatible = "ingenic,x1000-mac", "snps,dwmac";
-		reg = <0x134b0000 0x2000>;
+	i2c1: i2c-controller@10051000 {
+		compatible = "ingenic,x1000-i2c";
+		reg = <0x10051000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
 		interrupt-parent = <&intc>;
-		interrupts = <55>;
-		interrupt-names = "macirq";
+		interrupts = <59>;
 
-		clocks = <&cgu X1000_CLK_MAC>;
-		clock-names = "stmmaceth";
+		clocks = <&cgu X1000_CLK_I2C1>;
 
 		status = "disabled";
+	};
 
-		mdio: mdio {
-			compatible = "snps,dwmac-mdio";
-			#address-cells = <1>;
-			#size-cells = <0>;
+	i2c2: i2c-controller@10052000 {
+		compatible = "ingenic,x1000-i2c";
+		reg = <0x10052000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-			status = "disabled";
-		};
+		interrupt-parent = <&intc>;
+		interrupts = <58>;
+
+		clocks = <&cgu X1000_CLK_I2C2>;
+
+		status = "disabled";
+	};
+
+	pdma: dma-controller@13420000 {
+		compatible = "ingenic,x1000-dma";
+		reg = <0x13420000 0x400>, <0x13421000 0x40>;
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <10>;
+
+		clocks = <&cgu X1000_CLK_PDMA>;
 	};
 
 	msc0: mmc@13450000 {
@@ -311,4 +287,26 @@
 
 		status = "disabled";
 	};
+
+	mac: ethernet@134b0000 {
+		compatible = "ingenic,x1000-mac", "snps,dwmac";
+		reg = <0x134b0000 0x2000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <55>;
+		interrupt-names = "macirq";
+
+		clocks = <&cgu X1000_CLK_MAC>;
+		clock-names = "stmmaceth";
+
+		status = "disabled";
+
+		mdio: mdio {
+			compatible = "snps,dwmac-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+	};
 };
diff --git a/dts/src/mips/ingenic/x1830.dtsi b/dts/src/mips/ingenic/x1830.dtsi
new file mode 100644
index 0000000000..eb1214481a
--- /dev/null
+++ b/dts/src/mips/ingenic/x1830.dtsi
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/clock/x1830-cgu.h>
+#include <dt-bindings/dma/x1830-dma.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ingenic,x1830";
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	intc: interrupt-controller@10001000 {
+		compatible = "ingenic,x1830-intc", "ingenic,jz4780-intc";
+		reg = <0x10001000 0x50>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <2>;
+	};
+
+	exclk: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	rtclk: rtc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	cgu: x1830-cgu@10000000 {
+		compatible = "ingenic,x1830-cgu";
+		reg = <0x10000000 0x100>;
+
+		#clock-cells = <1>;
+
+		clocks = <&exclk>, <&rtclk>;
+		clock-names = "ext", "rtc";
+	};
+
+	tcu: timer@10002000 {
+		compatible = "ingenic,x1830-tcu", "ingenic,x1000-tcu", "simple-mfd";
+		reg = <0x10002000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10002000 0x1000>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu X1830_CLK_RTCLK
+			  &cgu X1830_CLK_EXCLK
+			  &cgu X1830_CLK_PCLK>;
+		clock-names = "rtc", "ext", "pclk";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <27 26 25>;
+
+		wdt: watchdog@0 {
+			compatible = "ingenic,x1830-watchdog", "ingenic,jz4780-watchdog";
+			reg = <0x0 0x10>;
+
+			clocks = <&tcu TCU_CLK_WDT>;
+			clock-names = "wdt";
+		};
+	};
+
+	rtc: rtc@10003000 {
+		compatible = "ingenic,x1830-rtc", "ingenic,jz4780-rtc";
+		reg = <0x10003000 0x4c>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <32>;
+
+		clocks = <&cgu X1830_CLK_RTCLK>;
+		clock-names = "rtc";
+	};
+
+	pinctrl: pin-controller@10010000 {
+		compatible = "ingenic,x1830-pinctrl";
+		reg = <0x10010000 0x800>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpa: gpio@0 {
+			compatible = "ingenic,x1830-gpio";
+			reg = <0>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <17>;
+		};
+
+		gpb: gpio@1 {
+			compatible = "ingenic,x1830-gpio";
+			reg = <1>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 32 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <16>;
+		};
+
+		gpc: gpio@2 {
+			compatible = "ingenic,x1830-gpio";
+			reg = <2>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 64 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <15>;
+		};
+
+		gpd: gpio@3 {
+			compatible = "ingenic,x1830-gpio";
+			reg = <3>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 96 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <14>;
+		};
+	};
+
+	uart0: serial@10030000 {
+		compatible = "ingenic,x1830-uart", "ingenic,x1000-uart";
+		reg = <0x10030000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <51>;
+
+		clocks = <&exclk>, <&cgu X1830_CLK_UART0>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart1: serial@10031000 {
+		compatible = "ingenic,x1830-uart", "ingenic,x1000-uart";
+		reg = <0x10031000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <50>;
+
+		clocks = <&exclk>, <&cgu X1830_CLK_UART1>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	i2c0: i2c-controller@10050000 {
+		compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+		reg = <0x10050000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <60>;
+
+		clocks = <&cgu X1830_CLK_SMB0>;
+
+		status = "disabled";
+	};
+
+	i2c1: i2c-controller@10051000 {
+		compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+		reg = <0x10051000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <59>;
+
+		clocks = <&cgu X1830_CLK_SMB1>;
+
+		status = "disabled";
+	};
+
+	i2c2: i2c-controller@10052000 {
+		compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+		reg = <0x10052000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <58>;
+
+		clocks = <&cgu X1830_CLK_SMB2>;
+
+		status = "disabled";
+	};
+
+	pdma: dma-controller@13420000 {
+		compatible = "ingenic,x1830-dma";
+		reg = <0x13420000 0x400
+			   0x13421000 0x40>;
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <10>;
+
+		clocks = <&cgu X1830_CLK_PDMA>;
+	};
+
+	msc0: mmc@13450000 {
+		compatible = "ingenic,x1830-mmc", "ingenic,x1000-mmc";
+		reg = <0x13450000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <37>;
+
+		clocks = <&cgu X1830_CLK_MSC0>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+
+		dmas = <&pdma X1830_DMA_MSC0_RX 0xffffffff>,
+			   <&pdma X1830_DMA_MSC0_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	msc1: mmc@13460000 {
+		compatible = "ingenic,x1830-mmc", "ingenic,x1000-mmc";
+		reg = <0x13460000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <36>;
+
+		clocks = <&cgu X1830_CLK_MSC1>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+
+		dmas = <&pdma X1830_DMA_MSC1_RX 0xffffffff>,
+			   <&pdma X1830_DMA_MSC1_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	mac: ethernet@134b0000 {
+		compatible = "ingenic,x1830-mac", "snps,dwmac";
+		reg = <0x134b0000 0x2000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <55>;
+		interrupt-names = "macirq";
+
+		clocks = <&cgu X1830_CLK_MAC>;
+		clock-names = "stmmaceth";
+
+		status = "disabled";
+
+		mdio: mdio {
+			compatible = "snps,dwmac-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+	};
+};