diff options
Diffstat (limited to 'drivers/net/realtek-dsa/rtl8365mb.c')
| -rw-r--r-- | drivers/net/realtek-dsa/rtl8365mb.c | 1255 |
1 files changed, 1255 insertions, 0 deletions
diff --git a/drivers/net/realtek-dsa/rtl8365mb.c b/drivers/net/realtek-dsa/rtl8365mb.c new file mode 100644 index 0000000000..5889982358 --- /dev/null +++ b/drivers/net/realtek-dsa/rtl8365mb.c @@ -0,0 +1,1255 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Realtek SMI subdriver for the Realtek RTL8365MB-VC ethernet switch. + * + * Copyright (C) 2021 Alvin Šipraga <alsi@bang-olufsen.dk> + * Copyright (C) 2021 Michael Rasmussen <mir@bang-olufsen.dk> + * + * The RTL8365MB-VC is a 4+1 port 10/100/1000M switch controller. It includes 4 + * integrated PHYs for the user facing ports, and an extension interface which + * can be connected to the CPU - or another PHY - via either MII, RMII, or + * RGMII. The switch is configured via the Realtek Simple Management Interface + * (SMI), which uses the MDIO/MDC lines. + * + * Below is a simplified block diagram of the chip and its relevant interfaces. + * + * .-----------------------------------. + * | | + * UTP <---------------> Giga PHY <-> PCS <-> P0 GMAC | + * UTP <---------------> Giga PHY <-> PCS <-> P1 GMAC | + * UTP <---------------> Giga PHY <-> PCS <-> P2 GMAC | + * UTP <---------------> Giga PHY <-> PCS <-> P3 GMAC | + * | | + * CPU/PHY <-MII/RMII/RGMII---> Extension <---> Extension | + * | interface 1 GMAC 1 | + * | | + * SMI driver/ <-MDC/SCL---> Management ~~~~~~~~~~~~~~ | + * EEPROM <-MDIO/SDA--> interface ~REALTEK ~~~~~ | + * | ~RTL8365MB ~~~ | + * | ~GXXXC TAIWAN~ | + * GPIO <--------------> Reset ~~~~~~~~~~~~~~ | + * | | + * Interrupt <----------> Link UP/DOWN events | + * controller | | + * '-----------------------------------' + * + * The driver uses DSA to integrate the 4 user and 1 extension ports into the + * kernel. Netdevices are created for the user ports, as are PHY devices for + * their integrated PHYs. The device tree firmware should also specify the link + * partner of the extension port - either via a fixed-link or other phy-handle. + * See the device tree bindings for more detailed information. Note that the + * driver has only been tested with a fixed-link, but in principle it should not + * matter. + * + * NOTE: Currently, only the RGMII interface is implemented in this driver. + * + * The interrupt line is asserted on link UP/DOWN events. The driver creates a + * custom irqchip to handle this interrupt and demultiplex the events by reading + * the status registers via SMI. Interrupts are then propagated to the relevant + * PHY device. + * + * The EEPROM contains initial register values which the chip will read over I2C + * upon hardware reset. It is also possible to omit the EEPROM. In both cases, + * the driver will manually reprogram some registers using jam tables to reach + * an initial state defined by the vendor driver. + * + * This Linux driver is written based on an OS-agnostic vendor driver from + * Realtek. The reference GPL-licensed sources can be found in the OpenWrt + * source tree under the name rtl8367c. The vendor driver claims to support a + * number of similar switch controllers from Realtek, but the only hardware we + * have is the RTL8365MB-VC. Moreover, there does not seem to be any chip under + * the name RTL8367C. Although one wishes that the 'C' stood for some kind of + * common hardware revision, there exist examples of chips with the suffix -VC + * which are explicitly not supported by the rtl8367c driver and which instead + * require the rtl8367d vendor driver. With all this uncertainty, the driver has + * been modestly named rtl8365mb. Future implementors may wish to rename things + * accordingly. + * + * In the same family of chips, some carry up to 8 user ports and up to 2 + * extension ports. Where possible this driver tries to make things generic, but + * more work must be done to support these configurations. According to + * documentation from Realtek, the family should include the following chips: + * + * - RTL8363NB + * - RTL8363NB-VB + * - RTL8363SC + * - RTL8363SC-VB + * - RTL8364NB + * - RTL8364NB-VB + * - RTL8365MB-VC + * - RTL8366SC + * - RTL8367RB-VB + * - RTL8367SB + * - RTL8367S + * - RTL8370MB + * - RTL8310SR + * + * Some of the register logic for these additional chips has been skipped over + * while implementing this driver. It is therefore not possible to assume that + * things will work out-of-the-box for other chips, and a careful review of the + * vendor driver may be needed to expand support. The RTL8365MB-VC seems to be + * one of the simpler chips. + */ + +#include <linux/bitfield.h> +#include <linux/bitops.h> +#include <linux/mutex.h> +#include <linux/spinlock.h> +#include <linux/printk.h> +#include <linux/export.h> +#include <linux/regmap.h> +#include <net.h> +#include <linux/if_bridge.h> + +#include "realtek.h" + +/* Family-specific data and limits */ +#define RTL8365MB_PHYADDRMAX 7 +#define RTL8365MB_NUM_PHYREGS 32 +#define RTL8365MB_PHYREGMAX (RTL8365MB_NUM_PHYREGS - 1) +#define RTL8365MB_MAX_NUM_PORTS 11 +#define RTL8365MB_MAX_NUM_EXTINTS 3 +#define RTL8365MB_LEARN_LIMIT_MAX 2112 + +/* Chip identification registers */ +#define RTL8365MB_CHIP_ID_REG 0x1300 + +#define RTL8365MB_CHIP_VER_REG 0x1301 + +#define RTL8365MB_MAGIC_REG 0x13C2 +#define RTL8365MB_MAGIC_VALUE 0x0249 + +/* Chip reset register */ +#define RTL8365MB_CHIP_RESET_REG 0x1322 +#define RTL8365MB_CHIP_RESET_SW_MASK 0x0002 +#define RTL8365MB_CHIP_RESET_HW_MASK 0x0001 + +/* Interrupt polarity register */ +#define RTL8365MB_INTR_POLARITY_REG 0x1100 +#define RTL8365MB_INTR_POLARITY_MASK 0x0001 +#define RTL8365MB_INTR_POLARITY_HIGH 0 +#define RTL8365MB_INTR_POLARITY_LOW 1 + +/* Interrupt control/status register - enable/check specific interrupt types */ +#define RTL8365MB_INTR_CTRL_REG 0x1101 +#define RTL8365MB_INTR_STATUS_REG 0x1102 +#define RTL8365MB_INTR_SLIENT_START_2_MASK 0x1000 +#define RTL8365MB_INTR_SLIENT_START_MASK 0x0800 +#define RTL8365MB_INTR_ACL_ACTION_MASK 0x0200 +#define RTL8365MB_INTR_CABLE_DIAG_FIN_MASK 0x0100 +#define RTL8365MB_INTR_INTERRUPT_8051_MASK 0x0080 +#define RTL8365MB_INTR_LOOP_DETECTION_MASK 0x0040 +#define RTL8365MB_INTR_GREEN_TIMER_MASK 0x0020 +#define RTL8365MB_INTR_SPECIAL_CONGEST_MASK 0x0010 +#define RTL8365MB_INTR_SPEED_CHANGE_MASK 0x0008 +#define RTL8365MB_INTR_LEARN_OVER_MASK 0x0004 +#define RTL8365MB_INTR_METER_EXCEEDED_MASK 0x0002 +#define RTL8365MB_INTR_LINK_CHANGE_MASK 0x0001 +#define RTL8365MB_INTR_ALL_MASK \ + (RTL8365MB_INTR_SLIENT_START_2_MASK | \ + RTL8365MB_INTR_SLIENT_START_MASK | \ + RTL8365MB_INTR_ACL_ACTION_MASK | \ + RTL8365MB_INTR_CABLE_DIAG_FIN_MASK | \ + RTL8365MB_INTR_INTERRUPT_8051_MASK | \ + RTL8365MB_INTR_LOOP_DETECTION_MASK | \ + RTL8365MB_INTR_GREEN_TIMER_MASK | \ + RTL8365MB_INTR_SPECIAL_CONGEST_MASK | \ + RTL8365MB_INTR_SPEED_CHANGE_MASK | \ + RTL8365MB_INTR_LEARN_OVER_MASK | \ + RTL8365MB_INTR_METER_EXCEEDED_MASK | \ + RTL8365MB_INTR_LINK_CHANGE_MASK) + +/* Per-port interrupt type status registers */ +#define RTL8365MB_PORT_LINKDOWN_IND_REG 0x1106 +#define RTL8365MB_PORT_LINKDOWN_IND_MASK 0x07FF + +#define RTL8365MB_PORT_LINKUP_IND_REG 0x1107 +#define RTL8365MB_PORT_LINKUP_IND_MASK 0x07FF + +/* PHY indirect access registers */ +#define RTL8365MB_INDIRECT_ACCESS_CTRL_REG 0x1F00 +#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK 0x0002 +#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_READ 0 +#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_WRITE 1 +#define RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK 0x0001 +#define RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE 1 +#define RTL8365MB_INDIRECT_ACCESS_STATUS_REG 0x1F01 +#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_REG 0x1F02 +#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_5_1_MASK GENMASK(4, 0) +#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK GENMASK(7, 5) +#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_9_6_MASK GENMASK(11, 8) +#define RTL8365MB_PHY_BASE 0x2000 +#define RTL8365MB_INDIRECT_ACCESS_WRITE_DATA_REG 0x1F03 +#define RTL8365MB_INDIRECT_ACCESS_READ_DATA_REG 0x1F04 + +/* PHY OCP address prefix register */ +#define RTL8365MB_GPHY_OCP_MSB_0_REG 0x1D15 +#define RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK 0x0FC0 +#define RTL8365MB_PHY_OCP_ADDR_PREFIX_MASK 0xFC00 + +/* The PHY OCP addresses of PHY registers 0~31 start here */ +#define RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE 0xA400 + +/* External interface port mode values - used in DIGITAL_INTERFACE_SELECT */ +#define RTL8365MB_EXT_PORT_MODE_DISABLE 0 +#define RTL8365MB_EXT_PORT_MODE_RGMII 1 +#define RTL8365MB_EXT_PORT_MODE_MII_MAC 2 +#define RTL8365MB_EXT_PORT_MODE_MII_PHY 3 +#define RTL8365MB_EXT_PORT_MODE_TMII_MAC 4 +#define RTL8365MB_EXT_PORT_MODE_TMII_PHY 5 +#define RTL8365MB_EXT_PORT_MODE_GMII 6 +#define RTL8365MB_EXT_PORT_MODE_RMII_MAC 7 +#define RTL8365MB_EXT_PORT_MODE_RMII_PHY 8 +#define RTL8365MB_EXT_PORT_MODE_SGMII 9 +#define RTL8365MB_EXT_PORT_MODE_HSGMII 10 +#define RTL8365MB_EXT_PORT_MODE_1000X_100FX 11 +#define RTL8365MB_EXT_PORT_MODE_1000X 12 +#define RTL8365MB_EXT_PORT_MODE_100FX 13 + +/* External interface mode configuration registers 0~1 */ +#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 0x1305 /* EXT1 */ +#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG1 0x13C3 /* EXT2 */ +#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(_extint) \ + ((_extint) == 1 ? RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 : \ + (_extint) == 2 ? RTL8365MB_DIGITAL_INTERFACE_SELECT_REG1 : \ + 0x0) +#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(_extint) \ + (0xF << (((_extint) % 2))) +#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(_extint) \ + (((_extint) % 2) * 4) + +/* External interface RGMII TX/RX delay configuration registers 0~2 */ +#define RTL8365MB_EXT_RGMXF_REG0 0x1306 /* EXT0 */ +#define RTL8365MB_EXT_RGMXF_REG1 0x1307 /* EXT1 */ +#define RTL8365MB_EXT_RGMXF_REG2 0x13C5 /* EXT2 */ +#define RTL8365MB_EXT_RGMXF_REG(_extint) \ + ((_extint) == 0 ? RTL8365MB_EXT_RGMXF_REG0 : \ + (_extint) == 1 ? RTL8365MB_EXT_RGMXF_REG1 : \ + (_extint) == 2 ? RTL8365MB_EXT_RGMXF_REG2 : \ + 0x0) +#define RTL8365MB_EXT_RGMXF_RXDELAY_MASK 0x0007 +#define RTL8365MB_EXT_RGMXF_TXDELAY_MASK 0x0008 + +/* External interface port speed values - used in DIGITAL_INTERFACE_FORCE */ +#define RTL8365MB_PORT_SPEED_10M 0 +#define RTL8365MB_PORT_SPEED_100M 1 +#define RTL8365MB_PORT_SPEED_1000M 2 + +/* External interface force configuration registers 0~2 */ +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 0x1310 /* EXT0 */ +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG1 0x1311 /* EXT1 */ +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG2 0x13C4 /* EXT2 */ +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(_extint) \ + ((_extint) == 0 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 : \ + (_extint) == 1 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG1 : \ + (_extint) == 2 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG2 : \ + 0x0) +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK 0x1000 +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_NWAY_MASK 0x0080 +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK 0x0040 +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_RXPAUSE_MASK 0x0020 +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK 0x0010 +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK 0x0004 +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK 0x0003 + +/* CPU port mask register - controls which ports are treated as CPU ports */ +#define RTL8365MB_CPU_PORT_MASK_REG 0x1219 +#define RTL8365MB_CPU_PORT_MASK_MASK 0x07FF + +/* CPU control register */ +#define RTL8365MB_CPU_CTRL_REG 0x121A +#define RTL8365MB_CPU_CTRL_TRAP_PORT_EXT_MASK 0x0400 +#define RTL8365MB_CPU_CTRL_TAG_FORMAT_MASK 0x0200 +#define RTL8365MB_CPU_CTRL_RXBYTECOUNT_MASK 0x0080 +#define RTL8365MB_CPU_CTRL_TAG_POSITION_MASK 0x0040 +#define RTL8365MB_CPU_CTRL_TRAP_PORT_MASK 0x0038 +#define RTL8365MB_CPU_CTRL_INSERTMODE_MASK 0x0006 +#define RTL8365MB_CPU_CTRL_EN_MASK 0x0001 + +/* Maximum packet length register */ +#define RTL8365MB_CFG0_MAX_LEN_REG 0x088C +#define RTL8365MB_CFG0_MAX_LEN_MASK 0x3FFF + +/* Port learning limit registers */ +#define RTL8365MB_LUT_PORT_LEARN_LIMIT_BASE 0x0A20 +#define RTL8365MB_LUT_PORT_LEARN_LIMIT_REG(_physport) \ + (RTL8365MB_LUT_PORT_LEARN_LIMIT_BASE + (_physport)) + +/* Port isolation (forwarding mask) registers */ +#define RTL8365MB_PORT_ISOLATION_REG_BASE 0x08A2 +#define RTL8365MB_PORT_ISOLATION_REG(_physport) \ + (RTL8365MB_PORT_ISOLATION_REG_BASE + (_physport)) +#define RTL8365MB_PORT_ISOLATION_MASK 0x07FF + +/* MSTP port state registers - indexed by tree instance */ +#define RTL8365MB_MSTI_CTRL_BASE 0x0A00 +#define RTL8365MB_MSTI_CTRL_REG(_msti, _physport) \ + (RTL8365MB_MSTI_CTRL_BASE + ((_msti) << 1) + ((_physport) >> 3)) +#define RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET(_physport) ((_physport) << 1) +#define RTL8365MB_MSTI_CTRL_PORT_STATE_MASK(_physport) \ + (0x3 << RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET((_physport))) + +struct rtl8365mb_jam_tbl_entry { + u16 reg; + u16 val; +}; + +/* Lifted from the vendor driver sources */ +static const struct rtl8365mb_jam_tbl_entry rtl8365mb_init_jam_8365mb_vc[] = { + { 0x13EB, 0x15BB }, { 0x1303, 0x06D6 }, { 0x1304, 0x0700 }, + { 0x13E2, 0x003F }, { 0x13F9, 0x0090 }, { 0x121E, 0x03CA }, + { 0x1233, 0x0352 }, { 0x1237, 0x00A0 }, { 0x123A, 0x0030 }, + { 0x1239, 0x0084 }, { 0x0301, 0x1000 }, { 0x1349, 0x001F }, + { 0x18E0, 0x4004 }, { 0x122B, 0x241C }, { 0x1305, 0xC000 }, + { 0x13F0, 0x0000 }, +}; + +static const struct rtl8365mb_jam_tbl_entry rtl8365mb_init_jam_common[] = { + { 0x1200, 0x7FCB }, { 0x0884, 0x0003 }, { 0x06EB, 0x0001 }, + { 0x03Fa, 0x0007 }, { 0x08C8, 0x00C0 }, { 0x0A30, 0x020E }, + { 0x0800, 0x0000 }, { 0x0802, 0x0000 }, { 0x09DA, 0x0013 }, + { 0x1D32, 0x0002 }, +}; + +enum rtl8365mb_phy_interface_mode { + RTL8365MB_PHY_INTERFACE_MODE_INVAL = 0, + RTL8365MB_PHY_INTERFACE_MODE_INTERNAL = BIT(0), + RTL8365MB_PHY_INTERFACE_MODE_MII = BIT(1), + RTL8365MB_PHY_INTERFACE_MODE_TMII = BIT(2), + RTL8365MB_PHY_INTERFACE_MODE_RMII = BIT(3), + RTL8365MB_PHY_INTERFACE_MODE_RGMII = BIT(4), + RTL8365MB_PHY_INTERFACE_MODE_SGMII = BIT(5), + RTL8365MB_PHY_INTERFACE_MODE_HSGMII = BIT(6), +}; + +/** + * struct rtl8365mb_extint - external interface info + * @port: the port with an external interface + * @id: the external interface ID, which is either 0, 1, or 2 + * @supported_interfaces: a bitmask of supported PHY interface modes + * + * Represents a mapping: port -> { id, supported_interfaces }. To be embedded + * in &struct rtl8365mb_chip_info for every port with an external interface. + */ +struct rtl8365mb_extint { + int port; + int id; + unsigned int supported_interfaces; +}; + +/** + * struct rtl8365mb_chip_info - static chip-specific info + * @name: human-readable chip name + * @chip_id: chip identifier + * @chip_ver: chip silicon revision + * @extints: available external interfaces + * @jam_table: chip-specific initialization jam table + * @jam_size: size of the chip's jam table + * + * These data are specific to a given chip in the family of switches supported + * by this driver. When adding support for another chip in the family, a new + * chip info should be added to the rtl8365mb_chip_infos array. + */ +struct rtl8365mb_chip_info { + const char *name; + u32 chip_id; + u32 chip_ver; + const struct rtl8365mb_extint extints[RTL8365MB_MAX_NUM_EXTINTS]; + const struct rtl8365mb_jam_tbl_entry *jam_table; + size_t jam_size; +}; + +/* Chip info for each supported switch in the family */ +#define PHY_INTF(_mode) (RTL8365MB_PHY_INTERFACE_MODE_ ## _mode) +static const struct rtl8365mb_chip_info rtl8365mb_chip_infos[] = { + { + .name = "RTL8365MB-VC", + .chip_id = 0x6367, + .chip_ver = 0x0040, + .extints = { + { 6, 1, PHY_INTF(MII) | PHY_INTF(TMII) | + PHY_INTF(RMII) | PHY_INTF(RGMII) }, + }, + .jam_table = rtl8365mb_init_jam_8365mb_vc, + .jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc), + }, + { + .name = "RTL8367S", + .chip_id = 0x6367, + .chip_ver = 0x00A0, + .extints = { + { 6, 1, PHY_INTF(SGMII) | PHY_INTF(HSGMII) }, + { 7, 2, PHY_INTF(MII) | PHY_INTF(TMII) | + PHY_INTF(RMII) | PHY_INTF(RGMII) }, + }, + .jam_table = rtl8365mb_init_jam_8365mb_vc, + .jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc), + }, + { + .name = "RTL8367RB-VB", + .chip_id = 0x6367, + .chip_ver = 0x0020, + .extints = { + { 6, 1, PHY_INTF(MII) | PHY_INTF(TMII) | + PHY_INTF(RMII) | PHY_INTF(RGMII) }, + { 7, 2, PHY_INTF(MII) | PHY_INTF(TMII) | + PHY_INTF(RMII) | PHY_INTF(RGMII) }, + }, + .jam_table = rtl8365mb_init_jam_8365mb_vc, + .jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc), + }, +}; + +enum rtl8365mb_stp_state { + RTL8365MB_STP_STATE_DISABLED = 0, + RTL8365MB_STP_STATE_BLOCKING = 1, + RTL8365MB_STP_STATE_LEARNING = 2, + RTL8365MB_STP_STATE_FORWARDING = 3, +}; + +enum rtl8365mb_cpu_insert { + RTL8365MB_CPU_INSERT_TO_ALL = 0, + RTL8365MB_CPU_INSERT_TO_TRAPPING = 1, + RTL8365MB_CPU_INSERT_TO_NONE = 2, +}; + +enum rtl8365mb_cpu_position { + RTL8365MB_CPU_POS_AFTER_SA = 0, + RTL8365MB_CPU_POS_BEFORE_CRC = 1, +}; + +enum rtl8365mb_cpu_format { + RTL8365MB_CPU_FORMAT_8BYTES = 0, + RTL8365MB_CPU_FORMAT_4BYTES = 1, +}; + +enum rtl8365mb_cpu_rxlen { + RTL8365MB_CPU_RXLEN_72BYTES = 0, + RTL8365MB_CPU_RXLEN_64BYTES = 1, +}; + +/** + * struct rtl8365mb_cpu - CPU port configuration + * @mask: port mask of ports that parse should parse CPU tags + * @trap_port: forward trapped frames to this port + * @insert: CPU tag insertion mode in switch->CPU frames + * @position: position of CPU tag in frame + * @rx_length: minimum CPU RX length + * @format: CPU tag format + * + * Represents the CPU tagging and CPU port configuration of the switch. These + * settings are configurable at runtime. + */ +struct rtl8365mb_cpu { + u32 mask; + u32 trap_port; + enum rtl8365mb_cpu_insert insert; + enum rtl8365mb_cpu_position position; + enum rtl8365mb_cpu_rxlen rx_length; + enum rtl8365mb_cpu_format format; +}; + +/** + * struct rtl8365mb_port - private per-port data + * @priv: pointer to parent realtek_priv data + * @index: DSA port index, same as dsa_port::index + */ +struct rtl8365mb_port { + struct realtek_priv *priv; + unsigned int index; +}; + +/** + * struct rtl8365mb - driver private data + * @priv: pointer to parent realtek_priv data + * @irq: registered IRQ or zero + * @chip_info: chip-specific info about the attached switch + * @cpu: CPU tagging and CPU port configuration for this chip + * @ports: per-port data + * + * Private data for this driver. + */ +struct rtl8365mb { + struct realtek_priv *priv; + const struct rtl8365mb_chip_info *chip_info; + struct rtl8365mb_cpu cpu; + struct rtl8365mb_port ports[RTL8365MB_MAX_NUM_PORTS]; +}; + +static int rtl8365mb_phy_poll_busy(struct realtek_priv *priv) +{ + u32 val; + + return regmap_read_poll_timeout(priv->map_nolock, + RTL8365MB_INDIRECT_ACCESS_STATUS_REG, + val, !val, 100); +} + +static int rtl8365mb_phy_ocp_prepare(struct realtek_priv *priv, int phy, + u32 ocp_addr) +{ + u32 val; + int ret; + + /* Set OCP prefix */ + val = FIELD_GET(RTL8365MB_PHY_OCP_ADDR_PREFIX_MASK, ocp_addr); + ret = regmap_update_bits( + priv->map_nolock, RTL8365MB_GPHY_OCP_MSB_0_REG, + RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK, + FIELD_PREP(RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK, val)); + if (ret) + return ret; + + /* Set PHY register address */ + val = RTL8365MB_PHY_BASE; + val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK, phy); + val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_5_1_MASK, + ocp_addr >> 1); + val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_9_6_MASK, + ocp_addr >> 6); + ret = regmap_write(priv->map_nolock, + RTL8365MB_INDIRECT_ACCESS_ADDRESS_REG, val); + if (ret) + return ret; + + return 0; +} + +static int rtl8365mb_phy_ocp_read(struct realtek_priv *priv, int phy, + u32 ocp_addr, u16 *data) +{ + u32 val; + int ret; + + ret = rtl8365mb_phy_poll_busy(priv); + if (ret) + goto out; + + ret = rtl8365mb_phy_ocp_prepare(priv, phy, ocp_addr); + if (ret) + goto out; + + /* Execute read operation */ + val = FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK, + RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE) | + FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK, + RTL8365MB_INDIRECT_ACCESS_CTRL_RW_READ); + ret = regmap_write(priv->map_nolock, RTL8365MB_INDIRECT_ACCESS_CTRL_REG, + val); + if (ret) + goto out; + + ret = rtl8365mb_phy_poll_busy(priv); + if (ret) + goto out; + + /* Get PHY register data */ + ret = regmap_read(priv->map_nolock, + RTL8365MB_INDIRECT_ACCESS_READ_DATA_REG, &val); + if (ret) + goto out; + + *data = val & 0xFFFF; + +out: + + return ret; +} + +static int rtl8365mb_phy_ocp_write(struct realtek_priv *priv, int phy, + u32 ocp_addr, u16 data) +{ + u32 val; + int ret; + + ret = rtl8365mb_phy_poll_busy(priv); + if (ret) + goto out; + + ret = rtl8365mb_phy_ocp_prepare(priv, phy, ocp_addr); + if (ret) + goto out; + + /* Set PHY register data */ + ret = regmap_write(priv->map_nolock, + RTL8365MB_INDIRECT_ACCESS_WRITE_DATA_REG, data); + if (ret) + goto out; + + /* Execute write operation */ + val = FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK, + RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE) | + FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK, + RTL8365MB_INDIRECT_ACCESS_CTRL_RW_WRITE); + ret = regmap_write(priv->map_nolock, RTL8365MB_INDIRECT_ACCESS_CTRL_REG, + val); + if (ret) + goto out; + + ret = rtl8365mb_phy_poll_busy(priv); + if (ret) + goto out; + +out: + return 0; +} + +static int rtl8365mb_phy_read(struct realtek_priv *priv, int phy, int regnum) +{ + u32 ocp_addr; + u16 val; + int ret; + + if (phy > RTL8365MB_PHYADDRMAX) + return -EINVAL; + + if (regnum > RTL8365MB_PHYREGMAX) + return -EINVAL; + + ocp_addr = RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE + regnum * 2; + + ret = rtl8365mb_phy_ocp_read(priv, phy, ocp_addr, &val); + if (ret) { + dev_err(priv->dev, + "failed to read PHY%d reg %02x @ %04x, ret %d\n", phy, + regnum, ocp_addr, ret); + return ret; + } + + dev_dbg(priv->dev, "read PHY%d register 0x%02x @ %04x, val <- %04x\n", + phy, regnum, ocp_addr, val); + + return val; +} + +static int rtl8365mb_phy_write(struct realtek_priv *priv, int phy, int regnum, + u16 val) +{ + u32 ocp_addr; + int ret; + + if (phy > RTL8365MB_PHYADDRMAX) + return -EINVAL; + + if (regnum > RTL8365MB_PHYREGMAX) + return -EINVAL; + + ocp_addr = RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE + regnum * 2; + + ret = rtl8365mb_phy_ocp_write(priv, phy, ocp_addr, val); + if (ret) { + dev_err(priv->dev, + "failed to write PHY%d reg %02x @ %04x, ret %d\n", phy, + regnum, ocp_addr, ret); + return ret; + } + + dev_dbg(priv->dev, "write PHY%d register 0x%02x @ %04x, val -> %04x\n", + phy, regnum, ocp_addr, val); + + return 0; +} + +static const struct rtl8365mb_extint * +rtl8365mb_get_port_extint(struct realtek_priv *priv, int port) +{ + struct rtl8365mb *mb = priv->chip_data; + int i; + + for (i = 0; i < RTL8365MB_MAX_NUM_EXTINTS; i++) { + const struct rtl8365mb_extint *extint = + &mb->chip_info->extints[i]; + + if (extint->port == port) + return extint; + } + + return NULL; +} + +static enum dsa_tag_protocol +rtl8365mb_get_tag_protocol(struct realtek_priv *priv) +{ + struct rtl8365mb_cpu *cpu; + struct rtl8365mb *mb; + + mb = priv->chip_data; + cpu = &mb->cpu; + + if (cpu->position == RTL8365MB_CPU_POS_BEFORE_CRC) + return DSA_TAG_PROTO_RTL8_4T; + + return DSA_TAG_PROTO_RTL8_4; +} + +static int rtl8365mb_ext_config_rgmii(struct realtek_priv *priv, int port, + phy_interface_t interface) +{ + const struct rtl8365mb_extint *extint = + rtl8365mb_get_port_extint(priv, port); + struct device_node *dn; + struct dsa_port *dp; + int tx_delay = 0; + int rx_delay = 0; + u32 val; + int ret; + + if (!extint) + return -ENODEV; + + dp = dsa_to_port(priv->ds, port); + dn = dp->dev->device_node; + + /* Set the RGMII TX/RX delay + * + * The Realtek vendor driver indicates the following possible + * configuration settings: + * + * TX delay: + * 0 = no delay, 1 = 2 ns delay + * RX delay: + * 0 = no delay, 7 = maximum delay + * Each step is approximately 0.3 ns, so the maximum delay is about + * 2.1 ns. + * + * The vendor driver also states that this must be configured *before* + * forcing the external interface into a particular mode, which is done + * in the rtl8365mb_phylink_mac_link_{up,down} functions. + * + * Only configure an RGMII TX (resp. RX) delay if the + * tx-internal-delay-ps (resp. rx-internal-delay-ps) OF property is + * specified. We ignore the detail of the RGMII interface mode + * (RGMII_{RXID, TXID, etc.}), as this is considered to be a PHY-only + * property. + */ + if (!of_property_read_u32(dn, "tx-internal-delay-ps", &val)) { + val = val / 1000; /* convert to ns */ + + if (val == 0 || val == 2) + tx_delay = val / 2; + else + dev_warn(priv->dev, + "RGMII TX delay must be 0 or 2 ns\n"); + } + + if (!of_property_read_u32(dn, "rx-internal-delay-ps", &val)) { + val = DIV_ROUND_CLOSEST(val, 300); /* convert to 0.3 ns step */ + + if (val <= 7) + rx_delay = val; + else + dev_warn(priv->dev, + "RGMII RX delay must be 0 to 2.1 ns\n"); + } + + ret = regmap_update_bits( + priv->map, RTL8365MB_EXT_RGMXF_REG(extint->id), + RTL8365MB_EXT_RGMXF_TXDELAY_MASK | + RTL8365MB_EXT_RGMXF_RXDELAY_MASK, + FIELD_PREP(RTL8365MB_EXT_RGMXF_TXDELAY_MASK, tx_delay) | + FIELD_PREP(RTL8365MB_EXT_RGMXF_RXDELAY_MASK, rx_delay)); + if (ret) + return ret; + + ret = regmap_update_bits( + priv->map, RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(extint->id), + RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(extint->id), + RTL8365MB_EXT_PORT_MODE_RGMII + << RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET( + extint->id)); + if (ret) + return ret; + + return 0; +} + +static int rtl8365mb_ext_config_forcemode(struct realtek_priv *priv, int port, + bool link, int speed, int duplex, + bool tx_pause, bool rx_pause) +{ + const struct rtl8365mb_extint *extint = + rtl8365mb_get_port_extint(priv, port); + u32 r_tx_pause; + u32 r_rx_pause; + u32 r_duplex; + u32 r_speed; + u32 r_link; + int val; + int ret; + + if (!extint) + return -ENODEV; + + if (link) { + /* Force the link up with the desired configuration */ + r_link = 1; + r_rx_pause = rx_pause ? 1 : 0; + r_tx_pause = tx_pause ? 1 : 0; + + if (speed == SPEED_1000) { + r_speed = RTL8365MB_PORT_SPEED_1000M; + } else if (speed == SPEED_100) { + r_speed = RTL8365MB_PORT_SPEED_100M; + } else if (speed == SPEED_10) { + r_speed = RTL8365MB_PORT_SPEED_10M; + } else { + dev_err(priv->dev, "unsupported port speed %d\n", + speed); + dump_stack(); + return -EINVAL; + } + + if (duplex == DUPLEX_FULL) { + r_duplex = 1; + } else if (duplex == DUPLEX_HALF) { + r_duplex = 0; + } else { + dev_err(priv->dev, "unsupported duplex mode %d\n", + duplex); + return -EINVAL; + } + } else { + /* Force the link down and reset any programmed configuration */ + r_link = 0; + r_tx_pause = 0; + r_rx_pause = 0; + r_speed = 0; + r_duplex = 0; + } + + val = FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK, 1) | + FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK, + r_tx_pause) | + FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_RXPAUSE_MASK, + r_rx_pause) | + FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK, r_link) | + FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK, + r_duplex) | + FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK, r_speed); + ret = regmap_write(priv->map, + RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(extint->id), + val); + if (ret) + return ret; + + return 0; +} + +static void rtl8365mb_port_stp_state_set(struct dsa_switch *ds, int port, + u8 state) +{ + struct realtek_priv *priv = ds->priv; + enum rtl8365mb_stp_state val; + int msti = 0; + + switch (state) { + case BR_STATE_DISABLED: + val = RTL8365MB_STP_STATE_DISABLED; + break; + case BR_STATE_FORWARDING: + val = RTL8365MB_STP_STATE_FORWARDING; + break; + default: + dev_err(priv->dev, "invalid STP state: %u\n", state); + return; + } + + regmap_update_bits(priv->map, RTL8365MB_MSTI_CTRL_REG(msti, port), + RTL8365MB_MSTI_CTRL_PORT_STATE_MASK(port), + val << RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET(port)); +} + +static int rtl8365mb_phylink_mac_config(struct dsa_port *dp, int port, + phy_interface_t phy_mode) +{ + struct realtek_priv *priv = dp->ds->priv; + int ret = 0; + + if (phy_interface_mode_is_rgmii(phy_mode)) { + ret = rtl8365mb_ext_config_rgmii(priv, port, phy_mode); + if (ret) + dev_err(priv->dev, + "failed to configure RGMII mode on port %d: %d\n", + port, ret); + } + + return ret; +} + +static void rtl8365mb_phylink_mac_link_down(struct dsa_port *dp, int port, + struct phy_device *phy) +{ + struct realtek_priv *priv = dp->ds->priv; + int ret; + + rtl8365mb_port_stp_state_set(dp->ds, port, BR_STATE_DISABLED); + + if (phy_interface_mode_is_rgmii(phy->interface)) { + ret = rtl8365mb_ext_config_forcemode(priv, port, false, + 0, 0, 0, 0); + if (ret) + dev_err(priv->dev, + "failed to reset forced mode on port %d: %d\n", + port, ret); + } +} + +static int rtl8365mb_phylink_mac_link_up(struct dsa_port *dp, int port, + struct phy_device *phy) +{ + struct realtek_priv *priv = dp->ds->priv; + int ret = 0; + + if (phy_interface_mode_is_rgmii(phy->interface)) { + ret = rtl8365mb_ext_config_forcemode(priv, port, true, + phy->speed, phy->duplex, + phy->pause, phy->pause); + if (ret) + dev_err(priv->dev, + "failed to force mode on port %d: %d\n", port, + ret); + } + + rtl8365mb_port_stp_state_set(dp->ds, port, BR_STATE_FORWARDING); + + return ret; +} + +static int rtl8365mb_port_set_learning(struct realtek_priv *priv, int port, + bool enable) +{ + /* Enable/disable learning by limiting the number of L2 addresses the + * port can learn. Realtek documentation states that a limit of zero + * disables learning. When enabling learning, set it to the chip's + * maximum. + */ + return regmap_write(priv->map, RTL8365MB_LUT_PORT_LEARN_LIMIT_REG(port), + enable ? RTL8365MB_LEARN_LIMIT_MAX : 0); +} + +static int rtl8365mb_port_set_isolation(struct realtek_priv *priv, int port, + u32 mask) +{ + return regmap_write(priv->map, RTL8365MB_PORT_ISOLATION_REG(port), mask); +} + +static int rtl8365mb_set_irq_enable(struct realtek_priv *priv, bool enable) +{ + return regmap_update_bits(priv->map, RTL8365MB_INTR_CTRL_REG, + RTL8365MB_INTR_LINK_CHANGE_MASK, + FIELD_PREP(RTL8365MB_INTR_LINK_CHANGE_MASK, + enable ? 1 : 0)); +} + +static int rtl8365mb_irq_disable(struct realtek_priv *priv) +{ + return rtl8365mb_set_irq_enable(priv, false); +} + +static int rtl8365mb_irq_setup(struct realtek_priv *priv) +{ + int ret; + + /* Disable the interrupt in case the chip has it enabled on reset */ + ret = rtl8365mb_irq_disable(priv); + if (ret) + return ret; + + /* Clear the interrupt status register */ + return regmap_write(priv->map, RTL8365MB_INTR_STATUS_REG, + RTL8365MB_INTR_ALL_MASK); +} + +static int rtl8365mb_cpu_config(struct realtek_priv *priv) +{ + struct rtl8365mb *mb = priv->chip_data; + struct rtl8365mb_cpu *cpu = &mb->cpu; + u32 val; + int ret; + + ret = regmap_update_bits(priv->map, RTL8365MB_CPU_PORT_MASK_REG, + RTL8365MB_CPU_PORT_MASK_MASK, + FIELD_PREP(RTL8365MB_CPU_PORT_MASK_MASK, + cpu->mask)); + if (ret) + return ret; + + val = FIELD_PREP(RTL8365MB_CPU_CTRL_EN_MASK, 1) | + FIELD_PREP(RTL8365MB_CPU_CTRL_INSERTMODE_MASK, cpu->insert) | + FIELD_PREP(RTL8365MB_CPU_CTRL_TAG_POSITION_MASK, cpu->position) | + FIELD_PREP(RTL8365MB_CPU_CTRL_RXBYTECOUNT_MASK, cpu->rx_length) | + FIELD_PREP(RTL8365MB_CPU_CTRL_TAG_FORMAT_MASK, cpu->format) | + FIELD_PREP(RTL8365MB_CPU_CTRL_TRAP_PORT_MASK, cpu->trap_port & 0x7) | + FIELD_PREP(RTL8365MB_CPU_CTRL_TRAP_PORT_EXT_MASK, + cpu->trap_port >> 3 & 0x1); + ret = regmap_write(priv->map, RTL8365MB_CPU_CTRL_REG, val); + if (ret) + return ret; + + return 0; +} + +static int rtl8365mb_change_tag_protocol(struct realtek_priv *priv, + enum dsa_tag_protocol proto) +{ + struct rtl8365mb_cpu *cpu; + struct rtl8365mb *mb; + + mb = priv->chip_data; + cpu = &mb->cpu; + + switch (proto) { + case DSA_TAG_PROTO_RTL8_4: + cpu->format = RTL8365MB_CPU_FORMAT_8BYTES; + cpu->position = RTL8365MB_CPU_POS_AFTER_SA; + break; + case DSA_TAG_PROTO_RTL8_4T: + cpu->format = RTL8365MB_CPU_FORMAT_8BYTES; + cpu->position = RTL8365MB_CPU_POS_BEFORE_CRC; + break; + /* The switch also supports a 4-byte format, similar to rtl4a but with + * the same 0x04 8-bit version and probably 8-bit port source/dest. + * There is no public doc about it. Not supported yet and it will probably + * never be. + */ + default: + return -EPROTONOSUPPORT; + } + + return rtl8365mb_cpu_config(priv); +} + +static int rtl8365mb_switch_init(struct realtek_priv *priv) +{ + struct rtl8365mb *mb = priv->chip_data; + const struct rtl8365mb_chip_info *ci; + int ret; + int i; + + ci = mb->chip_info; + + /* Do any chip-specific init jam before getting to the common stuff */ + if (ci->jam_table) { + for (i = 0; i < ci->jam_size; i++) { + ret = regmap_write(priv->map, ci->jam_table[i].reg, + ci->jam_table[i].val); + if (ret) + return ret; + } + } + + /* Common init jam */ + for (i = 0; i < ARRAY_SIZE(rtl8365mb_init_jam_common); i++) { + ret = regmap_write(priv->map, rtl8365mb_init_jam_common[i].reg, + rtl8365mb_init_jam_common[i].val); + if (ret) + return ret; + } + + return 0; +} + +static int rtl8365mb_reset_chip(struct realtek_priv *priv) +{ + u32 val; + + priv->write_reg_noack(priv, RTL8365MB_CHIP_RESET_REG, + FIELD_PREP(RTL8365MB_CHIP_RESET_HW_MASK, 1)); + + /* Realtek documentation says the chip needs 1 second to reset. Sleep + * for 100 ms before accessing any registers to prevent ACK timeouts. + */ + mdelay(100); + return regmap_read_poll_timeout(priv->map, RTL8365MB_CHIP_RESET_REG, val, + !(val & RTL8365MB_CHIP_RESET_HW_MASK), + 1e6); +} + +static int rtl8365mb_setup(struct realtek_priv *priv) +{ + struct rtl8365mb_cpu *cpu; + struct dsa_port *cpu_dp; + struct rtl8365mb *mb; + int ret; + int i; + + mb = priv->chip_data; + cpu = &mb->cpu; + + ret = rtl8365mb_reset_chip(priv); + if (ret) { + dev_err(priv->dev, "failed to reset chip: %d\n", ret); + goto out_error; + } + + /* Configure switch to vendor-defined initial state */ + ret = rtl8365mb_switch_init(priv); + if (ret) { + dev_err(priv->dev, "failed to initialize switch: %d\n", ret); + goto out_error; + } + + rtl8365mb_irq_setup(priv); + + /* Configure CPU tagging */ + dsa_switch_for_each_cpu_port(cpu_dp, priv->ds) { + cpu->mask |= BIT(cpu_dp->index); + + if (cpu->trap_port == RTL8365MB_MAX_NUM_PORTS) + cpu->trap_port = cpu_dp->index; + } + + if (cpu->mask == 0) { + dev_err(priv->dev, "no CPU port found\n"); + goto out_teardown_irq; + } + + ret = rtl8365mb_cpu_config(priv); + if (ret) + goto out_teardown_irq; + + /* Configure ports */ + for (i = 0; i < priv->num_ports; i++) { + struct rtl8365mb_port *p = &mb->ports[i]; + + /* Forward only to the CPU */ + ret = rtl8365mb_port_set_isolation(priv, i, cpu->mask); + if (ret) + goto out_teardown_irq; + + /* Disable learning */ + ret = rtl8365mb_port_set_learning(priv, i, false); + if (ret) + goto out_teardown_irq; + + /* Set the initial STP state of all ports to DISABLED, otherwise + * ports will still forward frames to the CPU despite being + * administratively down by default. + */ + rtl8365mb_port_stp_state_set(priv->ds, i, BR_STATE_DISABLED); + + /* Set up per-port private data */ + p->priv = priv; + p->index = i; + } + + /* Set maximum packet length to 1536 bytes */ + ret = regmap_update_bits(priv->map, RTL8365MB_CFG0_MAX_LEN_REG, + RTL8365MB_CFG0_MAX_LEN_MASK, + FIELD_PREP(RTL8365MB_CFG0_MAX_LEN_MASK, 1536)); + if (ret) + goto out_teardown_irq; + + if (priv->setup_interface) { + ret = priv->setup_interface(priv->ds); + if (ret) { + dev_err(priv->dev, "could not set up MDIO bus\n"); + goto out_teardown_irq; + } + } + + return 0; + +out_teardown_irq: +out_error: + return ret; +} + +static int rtl8365mb_get_chip_id_and_ver(struct regmap *map, u32 *id, u32 *ver) +{ + int ret; + + /* For some reason we have to write a magic value to an arbitrary + * register whenever accessing the chip ID/version registers. + */ + ret = regmap_write(map, RTL8365MB_MAGIC_REG, RTL8365MB_MAGIC_VALUE); + if (ret) + return ret; + + ret = regmap_read(map, RTL8365MB_CHIP_ID_REG, id); + if (ret) + return ret; + + ret = regmap_read(map, RTL8365MB_CHIP_VER_REG, ver); + if (ret) + return ret; + + /* Reset magic register */ + ret = regmap_write(map, RTL8365MB_MAGIC_REG, 0); + if (ret) + return ret; + + return 0; +} + +static int rtl8365mb_detect(struct realtek_priv *priv) +{ + struct rtl8365mb *mb = priv->chip_data; + u32 chip_id; + u32 chip_ver; + int ret; + int i; + + ret = rtl8365mb_get_chip_id_and_ver(priv->map, &chip_id, &chip_ver); + if (ret) { + dev_err(priv->dev, "failed to read chip id and version: %d\n", + ret); + return ret; + } + + for (i = 0; i < ARRAY_SIZE(rtl8365mb_chip_infos); i++) { + const struct rtl8365mb_chip_info *ci = &rtl8365mb_chip_infos[i]; + + if (ci->chip_id == chip_id && ci->chip_ver == chip_ver) { + mb->chip_info = ci; + break; + } + } + + if (!mb->chip_info) { + dev_err(priv->dev, + "unrecognized switch (id=0x%04x, ver=0x%04x)\n", chip_id, + chip_ver); + return -ENODEV; + } + + dev_info(priv->dev, "found an %s switch\n", mb->chip_info->name); + + priv->num_ports = RTL8365MB_MAX_NUM_PORTS; + mb->priv = priv; + mb->cpu.trap_port = RTL8365MB_MAX_NUM_PORTS; + mb->cpu.insert = RTL8365MB_CPU_INSERT_TO_ALL; + mb->cpu.position = RTL8365MB_CPU_POS_AFTER_SA; + mb->cpu.rx_length = RTL8365MB_CPU_RXLEN_64BYTES; + mb->cpu.format = RTL8365MB_CPU_FORMAT_8BYTES; + + return 0; +} + +static const struct dsa_switch_ops rtl8365mb_switch_ops = { + .port_pre_enable = rtl8365mb_phylink_mac_config, + .port_disable = rtl8365mb_phylink_mac_link_down, + .port_enable = rtl8365mb_phylink_mac_link_up, +}; + +static const struct realtek_ops rtl8365mb_ops = { + .detect = rtl8365mb_detect, + .phy_read = rtl8365mb_phy_read, + .phy_write = rtl8365mb_phy_write, + .setup = rtl8365mb_setup, + .get_tag_protocol = rtl8365mb_get_tag_protocol, + .change_tag_protocol = rtl8365mb_change_tag_protocol, +}; + +const struct realtek_variant rtl8365mb_variant = { + .ds_ops = &rtl8365mb_switch_ops, + .ops = &rtl8365mb_ops, + .clk_delay = 10, + .cmd_read = 0xb9, + .cmd_write = 0xb8, + .chip_data_sz = sizeof(struct rtl8365mb), +}; +EXPORT_SYMBOL_GPL(rtl8365mb_variant); + +MODULE_AUTHOR("Alvin Šipraga <alsi@bang-olufsen.dk>"); +MODULE_DESCRIPTION("Driver for RTL8365MB-VC ethernet switch"); +MODULE_LICENSE("GPL"); |