1 files changed, 0 insertions, 112 deletions
diff --git a/dts/Bindings/display/bridge/cdns,dsi.txt b/dts/Bindings/display/bridge/cdns,dsi.txt
deleted file mode 100644
index 525a4bfd86..0000000000
--- a/dts/Bindings/display/bridge/cdns,dsi.txt
+++ /dev/null
@@ -1,112 +0,0 @@
-Cadence DSI bridge
-==================
-
-The Cadence DSI bridge is a DPI to DSI bridge supporting up to 4 DSI lanes.
-
-Required properties:
-- compatible: should be set to "cdns,dsi".
-- reg: physical base address and length of the controller's registers.
-- interrupts: interrupt line connected to the DSI bridge.
-- clocks: DSI bridge clocks.
-- clock-names: must contain "dsi_p_clk" and "dsi_sys_clk".
-- phys: phandle link to the MIPI D-PHY controller.
-- phy-names: must contain "dphy".
-- #address-cells: must be set to 1.
-- #size-cells: must be set to 0.
-
-Optional properties:
-- resets: DSI reset lines.
-- reset-names: can contain "dsi_p_rst".
-
-Required subnodes:
-- ports: Ports as described in Documentation/devicetree/bindings/graph.txt.
-  2 ports are available:
-  * port 0: this port is only needed if some of your DSI devices are
-	    controlled through  an external bus like I2C or SPI. Can have at
-	    most 4 endpoints. The endpoint number is directly encoding the
-	    DSI virtual channel used by this device.
-  * port 1: represents the DPI input.
-  Other ports will be added later to support the new kind of inputs.
-
-- one subnode per DSI device connected on the DSI bus. Each DSI device should
-  contain a reg property encoding its virtual channel.
-
-Example:
-	dsi0: dsi@fd0c0000 {
-		compatible = "cdns,dsi";
-		reg = <0x0 0xfd0c0000 0x0 0x1000>;
-		clocks = <&pclk>, <&sysclk>;
-		clock-names = "dsi_p_clk", "dsi_sys_clk";
-		interrupts = <1>;
-		phys = <&dphy0>;
-		phy-names = "dphy";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@1 {
-				reg = <1>;
-				dsi0_dpi_input: endpoint {
-					remote-endpoint = <&xxx_dpi_output>;
-				};
-			};
-		};
-
-		panel: dsi-dev@0 {
-			compatible = "<vendor,panel>";
-			reg = <0>;
-		};
-	};
-
-or
-
-	dsi0: dsi@fd0c0000 {
-		compatible = "cdns,dsi";
-		reg = <0x0 0xfd0c0000 0x0 0x1000>;
-		clocks = <&pclk>, <&sysclk>;
-		clock-names = "dsi_p_clk", "dsi_sys_clk";
-		interrupts = <1>;
-		phys = <&dphy1>;
-		phy-names = "dphy";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				dsi0_output: endpoint@0 {
-					reg = <0>;
-					remote-endpoint = <&dsi_panel_input>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				dsi0_dpi_input: endpoint {
-					remote-endpoint = <&xxx_dpi_output>;
-				};
-			};
-		};
-	};
-
-	i2c@xxx {
-		panel: panel@59 {
-			compatible = "<vendor,panel>";
-			reg = <0x59>;
-
-			port {
-				dsi_panel_input: endpoint {
-					remote-endpoint = <&dsi0_output>;
-				};
-			};
-		};
-	};