1 files changed, 0 insertions, 99 deletions
diff --git a/dts/Bindings/i2c/i2c-mux-gpmux.txt b/dts/Bindings/i2c/i2c-mux-gpmux.txt
deleted file mode 100644
index 8b444b94e9..0000000000
--- a/dts/Bindings/i2c/i2c-mux-gpmux.txt
+++ /dev/null
@@ -1,99 +0,0 @@
-General Purpose I2C Bus Mux
-
-This binding describes an I2C bus multiplexer that uses a mux controller
-from the mux subsystem to route the I2C signals.
-
-                                  .-----.  .-----.
-                                  | dev |  | dev |
-    .------------.                '-----'  '-----'
-    | SoC        |                   |        |
-    |            |          .--------+--------'
-    |   .------. |  .------+    child bus A, on MUX value set to 0
-    |   | I2C  |-|--| Mux  |
-    |   '------' |  '--+---+    child bus B, on MUX value set to 1
-    |   .------. |     |    '----------+--------+--------.
-    |   | MUX- | |     |               |        |        |
-    |   | Ctrl |-|-----+            .-----.  .-----.  .-----.
-    |   '------' |                  | dev |  | dev |  | dev |
-    '------------'                  '-----'  '-----'  '-----'
-
-Required properties:
-- compatible: i2c-mux
-- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
-  port is connected to.
-- mux-controls: The phandle of the mux controller to use for operating the
-  mux.
-* Standard I2C mux properties. See i2c-mux.txt in this directory.
-* I2C child bus nodes. See i2c-mux.txt in this directory. The sub-bus number
-  is also the mux-controller state described in ../mux/mux-controller.txt
-
-Optional properties:
-- mux-locked: If present, explicitly allow unrelated I2C transactions on the
-  parent I2C adapter at these times:
-   + during setup of the multiplexer
-   + between setup of the multiplexer and the child bus I2C transaction
-   + between the child bus I2C transaction and releasing of the multiplexer
-   + during releasing of the multiplexer
-  However, I2C transactions to devices behind all I2C multiplexers connected
-  to the same parent adapter that this multiplexer is connected to are blocked
-  for the full duration of the complete multiplexed I2C transaction (i.e.
-  including the times covered by the above list).
-  If mux-locked is not present, the multiplexer is assumed to be parent-locked.
-  This means that no unrelated I2C transactions are allowed on the parent I2C
-  adapter for the complete multiplexed I2C transaction.
-  The properties of mux-locked and parent-locked multiplexers are discussed
-  in more detail in Documentation/i2c/i2c-topology.rst.
-
-For each i2c child node, an I2C child bus will be created. They will
-be numbered based on their order in the device tree.
-
-Whenever an access is made to a device on a child bus, the value set
-in the relevant node's reg property will be set as the state in the
-mux controller.
-
-Example:
-	mux: mux-controller {
-		compatible = "gpio-mux";
-		#mux-control-cells = <0>;
-
-		mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>,
-			    <&pioA 1 GPIO_ACTIVE_HIGH>;
-	};
-
-	i2c-mux {
-		compatible = "i2c-mux";
-		mux-locked;
-		i2c-parent = <&i2c1>;
-
-		mux-controls = <&mux>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			ssd1307: oled@3c {
-				compatible = "solomon,ssd1307fb-i2c";
-				reg = <0x3c>;
-				pwms = <&pwm 4 3000>;
-				reset-gpios = <&gpio2 7 1>;
-				reset-active-low;
-			};
-		};
-
-		i2c@3 {
-			reg = <3>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			pca9555: pca9555@20 {
-				compatible = "nxp,pca9555";
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x20>;
-			};
-		};
-	};