diff options
Diffstat (limited to 'dts/Bindings/iio/adc/st,stm32-adc.yaml')
| -rw-r--r-- | dts/Bindings/iio/adc/st,stm32-adc.yaml | 608 |
1 files changed, 608 insertions, 0 deletions
diff --git a/dts/Bindings/iio/adc/st,stm32-adc.yaml b/dts/Bindings/iio/adc/st,stm32-adc.yaml new file mode 100644 index 0000000000..995cbf8cef --- /dev/null +++ b/dts/Bindings/iio/adc/st,stm32-adc.yaml @@ -0,0 +1,608 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/st,stm32-adc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32 ADC + +description: | + STM32 ADC is a successive approximation analog-to-digital converter. + It has several multiplexed input channels. Conversions can be performed + in single, continuous, scan or discontinuous mode. Result of the ADC is + stored in a left-aligned or right-aligned 32-bit data register. + Conversions can be launched in software or using hardware triggers. + + The analog watchdog feature allows the application to detect if the input + voltage goes beyond the user-defined, higher or lower thresholds. + + Each STM32 ADC block can have up to 3 ADC instances. + +maintainers: + - Fabrice Gasnier <fabrice.gasnier@foss.st.com> + +properties: + compatible: + enum: + - st,stm32f4-adc-core + - st,stm32h7-adc-core + - st,stm32mp1-adc-core + - st,stm32mp13-adc-core + + reg: + maxItems: 1 + + interrupts: + description: | + One or more interrupts for ADC block, depending on part used: + - stm32f4 and stm32h7 share a common ADC interrupt line. + - stm32mp1 has two separate interrupt lines, one for each ADC within + ADC block. + - stm32mp13 has an interrupt line per ADC block. + minItems: 1 + maxItems: 2 + + clocks: + minItems: 1 + maxItems: 2 + description: | + Core can use up to two clocks, depending on part used: + - "adc" clock: for the analog circuitry, common to all ADCs. + It's required on stm32f4. + It's optional on stm32h7 and stm32mp1. + - "bus" clock: for registers access, common to all ADCs. + It's not present on stm32f4. + It's required on stm32h7 and stm32mp1. + + clock-names: true + + st,max-clk-rate-hz: + description: + Allow to specify desired max clock rate used by analog circuitry. + + vdda-supply: + description: Phandle to the vdda input analog voltage. + + vref-supply: + description: Phandle to the vref input analog reference voltage. + + booster-supply: + description: + Phandle to the embedded booster regulator that can be used to supply ADC + analog input switches on stm32h7 and stm32mp1. + + vdd-supply: + description: + Phandle to the vdd input voltage. It can be used to supply ADC analog + input switches on stm32mp1. + + st,syscfg: + description: + Phandle to system configuration controller. It can be used to control the + analog circuitry on stm32mp1. + $ref: /schemas/types.yaml#/definitions/phandle-array + + interrupt-controller: true + + '#interrupt-cells': + const: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +allOf: + - if: + properties: + compatible: + contains: + const: st,stm32f4-adc-core + + then: + properties: + clocks: + maxItems: 1 + + clock-names: + const: adc + + interrupts: + items: + - description: interrupt line common for all ADCs + + st,max-clk-rate-hz: + minimum: 600000 + maximum: 36000000 + default: 36000000 + + booster-supply: false + + vdd-supply: false + + st,syscfg: false + + - if: + properties: + compatible: + contains: + const: st,stm32h7-adc-core + + then: + properties: + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + items: + - const: bus + - const: adc + minItems: 1 + + interrupts: + items: + - description: interrupt line common for all ADCs + + st,max-clk-rate-hz: + minimum: 120000 + maximum: 36000000 + default: 36000000 + + vdd-supply: false + + st,syscfg: false + + - if: + properties: + compatible: + contains: + const: st,stm32mp1-adc-core + + then: + properties: + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + items: + - const: bus + - const: adc + minItems: 1 + + interrupts: + items: + - description: interrupt line for ADC1 + - description: interrupt line for ADC2 + + st,max-clk-rate-hz: + minimum: 120000 + maximum: 36000000 + default: 36000000 + + - if: + properties: + compatible: + contains: + const: st,stm32mp13-adc-core + + then: + properties: + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + items: + - const: bus + - const: adc + minItems: 1 + + interrupts: + items: + - description: ADC interrupt line + + st,max-clk-rate-hz: + minimum: 150000 + maximum: 75000000 + default: 75000000 + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - vdda-supply + - vref-supply + - interrupt-controller + - '#interrupt-cells' + - '#address-cells' + - '#size-cells' + +patternProperties: + "^adc@[0-9]+$": + type: object + description: + An ADC block node should contain at least one subnode, representing an + ADC instance available on the machine. + + properties: + compatible: + enum: + - st,stm32f4-adc + - st,stm32h7-adc + - st,stm32mp1-adc + - st,stm32mp13-adc + + reg: + description: | + Offset of ADC instance in ADC block. Valid values are: + - 0x0: ADC1 + - 0x100: ADC2 + - 0x200: ADC3 (stm32f4 only) + maxItems: 1 + + '#io-channel-cells': + const: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + interrupts: + description: | + IRQ Line for the ADC instance. Valid values are: + - 0 for adc@0 (single adc for stm32mp13) + - 1 for adc@100 + - 2 for adc@200 (stm32f4 only) + maxItems: 1 + + clocks: + description: + Input clock private to this ADC instance. It's required only on + stm32f4, that has per instance clock input for registers access. + maxItems: 1 + + dmas: + description: RX DMA Channel + maxItems: 1 + + dma-names: + const: rx + + assigned-resolution-bits: + description: | + Resolution (bits) to use for conversions: + - can be 6, 8, 10 or 12 on stm32f4 and stm32mp13 + - can be 8, 10, 12, 14 or 16 on stm32h7 and stm32mp1 + + st,adc-channels: + description: | + List of single-ended channels muxed for this ADC. It can have up to: + - 16 channels, numbered from 0 to 15 (for in0..in15) on stm32f4 + - 19 channels, numbered from 0 to 18 (for in0..in18) on stm32mp13. + - 20 channels, numbered from 0 to 19 (for in0..in19) on stm32h7 and + stm32mp1. + $ref: /schemas/types.yaml#/definitions/uint32-array + deprecated: true + + st,adc-diff-channels: + description: | + List of differential channels muxed for this ADC. Some channels can + be configured as differential instead of single-ended on stm32h7 and + on stm32mp1. Positive and negative inputs pairs are listed: + <vinp vinn>, <vinp vinn>,... vinp and vinn are numbered from 0 to 19. + + Note: At least one of "st,adc-channels" or "st,adc-diff-channels" is + required if no adc generic channel is defined. These legacy channel + properties are exclusive with adc generic channel bindings. + Both properties can be used together. Some channels can be + used as single-ended and some other ones as differential (mixed). But + channels can't be configured both as single-ended and differential. + $ref: /schemas/types.yaml#/definitions/uint32-matrix + items: + items: + - description: | + "vinp" indicates positive input number + minimum: 0 + maximum: 19 + - description: | + "vinn" indicates negative input number + minimum: 0 + maximum: 19 + deprecated: true + + st,min-sample-time-nsecs: + description: + Minimum sampling time in nanoseconds. Depending on hardware (board) + e.g. high/low analog input source impedance, fine tune of ADC + sampling time may be recommended. This can be either one value or an + array that matches "st,adc-channels" and/or "st,adc-diff-channels" + list, to set sample time resp. for all channels, or independently for + each channel. + $ref: /schemas/types.yaml#/definitions/uint32-array + deprecated: true + + nvmem-cells: + items: + - description: Phandle to the calibration vrefint data provided by otp + + nvmem-cell-names: + items: + - const: vrefint + + patternProperties: + "^channel@([0-9]|1[0-9])$": + type: object + $ref: adc.yaml + description: Represents the external channels which are connected to the ADC. + + properties: + reg: + items: + minimum: 0 + maximum: 19 + + label: + description: | + Unique name to identify which channel this is. + Reserved label names "vddcore", "vddcpu", "vddq_ddr", "vrefint" and "vbat" + are used to identify internal channels with matching names. + + diff-channels: + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + minimum: 0 + maximum: 19 + + st,min-sample-time-ns: + description: | + Minimum sampling time in nanoseconds. Depending on hardware (board) + e.g. high/low analog input source impedance, fine tune of ADC + sampling time may be recommended. + + required: + - reg + + additionalProperties: false + + allOf: + - if: + properties: + compatible: + contains: + const: st,stm32f4-adc + + then: + properties: + reg: + enum: + - 0x0 + - 0x100 + - 0x200 + + interrupts: + minimum: 0 + maximum: 2 + + assigned-resolution-bits: + enum: [6, 8, 10, 12] + default: 12 + + st,adc-channels: + minItems: 1 + maxItems: 16 + items: + minimum: 0 + maximum: 15 + + st,adc-diff-channels: false + + st,min-sample-time-nsecs: + minItems: 1 + maxItems: 16 + items: + minimum: 80 + + required: + - clocks + + - if: + properties: + compatible: + contains: + enum: + - st,stm32h7-adc + - st,stm32mp1-adc + + then: + properties: + reg: + enum: + - 0x0 + - 0x100 + + interrupts: + minimum: 0 + maximum: 1 + + assigned-resolution-bits: + enum: [8, 10, 12, 14, 16] + default: 16 + + st,adc-channels: + minItems: 1 + maxItems: 20 + items: + minimum: 0 + maximum: 19 + + st,min-sample-time-nsecs: + minItems: 1 + maxItems: 20 + items: + minimum: 40 + + + - if: + properties: + compatible: + contains: + const: st,stm32mp13-adc + + then: + properties: + reg: + const: 0x0 + + interrupts: + const: 0 + + assigned-resolution-bits: + enum: [6, 8, 10, 12] + default: 12 + + st,adc-channels: + minItems: 1 + maxItems: 19 + items: + minimum: 0 + maximum: 18 + + st,min-sample-time-nsecs: + minItems: 1 + maxItems: 19 + items: + minimum: 40 + additionalProperties: false + + required: + - compatible + - reg + - interrupts + - '#io-channel-cells' + +examples: + - | + // Example 1: with stm32f429, ADC1, single-ended channel 8 + adc123: adc@40012000 { + compatible = "st,stm32f4-adc-core"; + reg = <0x40012000 0x400>; + interrupts = <18>; + clocks = <&rcc 0 168>; + clock-names = "adc"; + st,max-clk-rate-hz = <36000000>; + vdda-supply = <&vdda>; + vref-supply = <&vref>; + interrupt-controller; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + adc@0 { + compatible = "st,stm32f4-adc"; + #io-channel-cells = <1>; + reg = <0x0>; + clocks = <&rcc 0 168>; + interrupt-parent = <&adc123>; + interrupts = <0>; + st,adc-channels = <8>; + dmas = <&dma2 0 0 0x400 0x0>; + dma-names = "rx"; + assigned-resolution-bits = <8>; + }; + // ... + // other adc child nodes follow... + }; + + - | + // Example 2: with stm32mp157c to setup ADC1 with: + // - channels 0 & 1 as single-ended + // - channels 2 & 3 as differential (with resp. 6 & 7 negative inputs) + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/stm32mp1-clks.h> + adc12: adc@48003000 { + compatible = "st,stm32mp1-adc-core"; + reg = <0x48003000 0x400>; + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc ADC12>, <&rcc ADC12_K>; + clock-names = "bus", "adc"; + booster-supply = <&booster>; + vdd-supply = <&vdd>; + vdda-supply = <&vdda>; + vref-supply = <&vref>; + st,syscfg = <&syscfg>; + interrupt-controller; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + adc@0 { + compatible = "st,stm32mp1-adc"; + #io-channel-cells = <1>; + reg = <0x0>; + interrupt-parent = <&adc12>; + interrupts = <0>; + st,adc-channels = <0 1>; + st,adc-diff-channels = <2 6>, <3 7>; + st,min-sample-time-nsecs = <5000>; + dmas = <&dmamux1 9 0x400 0x05>; + dma-names = "rx"; + }; + // ... + // other adc child node follow... + }; + + - | + // Example 3: with stm32mp157c to setup ADC2 with: + // - internal channels 13, 14, 15. + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/stm32mp1-clks.h> + adc122: adc@48003000 { + compatible = "st,stm32mp1-adc-core"; + reg = <0x48003000 0x400>; + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc ADC12>, <&rcc ADC12_K>; + clock-names = "bus", "adc"; + booster-supply = <&booster>; + vdd-supply = <&vdd>; + vdda-supply = <&vdda>; + vref-supply = <&vref>; + st,syscfg = <&syscfg>; + interrupt-controller; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + adc@100 { + compatible = "st,stm32mp1-adc"; + #io-channel-cells = <1>; + reg = <0x100>; + interrupts = <1>; + #address-cells = <1>; + #size-cells = <0>; + channel@13 { + reg = <13>; + label = "vrefint"; + st,min-sample-time-ns = <9000>; + }; + channel@14 { + reg = <14>; + label = "vddcore"; + st,min-sample-time-ns = <9000>; + }; + channel@15 { + reg = <15>; + label = "vbat"; + st,min-sample-time-ns = <9000>; + }; + }; + }; + +... |