diff options
Diffstat (limited to 'dts/Bindings/iio/resolver/adi,ad2s1210.yaml')
| -rw-r--r-- | dts/Bindings/iio/resolver/adi,ad2s1210.yaml | 177 |
1 files changed, 177 insertions, 0 deletions
diff --git a/dts/Bindings/iio/resolver/adi,ad2s1210.yaml b/dts/Bindings/iio/resolver/adi,ad2s1210.yaml new file mode 100644 index 0000000000..8980b3cd83 --- /dev/null +++ b/dts/Bindings/iio/resolver/adi,ad2s1210.yaml @@ -0,0 +1,177 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/resolver/adi,ad2s1210.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD2S1210 Resolver-to-Digital Converter + +maintainers: + - Michael Hennerich <michael.hennerich@analog.com> + +description: | + The AD2S1210 is a complete 10-bit to 16-bit resolution tracking + resolver-to-digital converter, integrating an on-board programmable + sinusoidal oscillator that provides sine wave excitation for + resolvers. + + The AD2S1210 allows the user to read the angular position or the + angular velocity data directly from the parallel outputs or through + the serial interface. + + The mode of operation of the communication channel (parallel or serial) is + selected by the A0 and A1 input pins. In normal mode, data is latched by + toggling the SAMPLE line and can then be read directly. In configuration mode, + data is read or written using a register access scheme (address byte with + read/write flag and data byte). + + A1 A0 Result + 0 0 Normal mode - position output + 0 1 Normal mode - velocity output + 1 0 Reserved + 1 1 Configuration mode + + In normal mode, the resolution of the digital output is selected using + the RES0 and RES1 input pins. In configuration mode, the resolution is + selected by setting the RES0 and RES1 bits in the control register. + + RES1 RES0 Resolution (Bits) + 0 0 10 + 0 1 12 + 1 0 14 + 1 1 16 + + Note on SPI connections: The CS line on the AD2S1210 should hard-wired to + logic low and the WR/FSYNC line on the AD2S1210 should be connected to the + SPI CSn output of the SPI controller. + + Datasheet: + https://www.analog.com/media/en/technical-documentation/data-sheets/ad2s1210.pdf + +properties: + compatible: + const: adi,ad2s1210 + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 25000000 + + spi-cpha: true + + avdd-supply: + description: + A 4.75 to 5.25 V regulator that powers the Analog Supply Voltage (AVDD) + pin. + + dvdd-supply: + description: + A 4.75 to 5.25 V regulator that powers the Digital Supply Voltage (DVDD) + pin. + + vdrive-supply: + description: + A 2.3 to 5.25 V regulator that powers the Logic Power Supply Input + (VDrive) pin. + + clocks: + maxItems: 1 + description: External oscillator clock (CLKIN). + + reset-gpios: + description: + GPIO connected to the /RESET pin. As the line needs to be low for the + reset to be active, it should be configured as GPIO_ACTIVE_LOW. + maxItems: 1 + + sample-gpios: + description: + GPIO connected to the /SAMPLE pin. As the line needs to be low to trigger + a sample, it should be configured as GPIO_ACTIVE_LOW. + maxItems: 1 + + mode-gpios: + description: + GPIO lines connected to the A0 and A1 pins. These pins select the data + transfer mode. + minItems: 2 + maxItems: 2 + + resolution-gpios: + description: + GPIO lines connected to the RES0 and RES1 pins. These pins select the + resolution of the digital output. If omitted, it is assumed that the + RES0 and RES1 pins are hard-wired to match the assigned-resolution-bits + property. + minItems: 2 + maxItems: 2 + + fault-gpios: + description: + GPIO lines connected to the LOT and DOS pins. These pins combined indicate + the type of fault present, if any. As these pins a pulled low to indicate + a fault condition, they should be configured as GPIO_ACTIVE_LOW. + minItems: 2 + maxItems: 2 + + adi,fixed-mode: + description: + This is used to indicate the selected mode if A0 and A1 are hard-wired + instead of connected to GPIOS (i.e. mode-gpios is omitted). + $ref: /schemas/types.yaml#/definitions/string + enum: [config, velocity, position] + + assigned-resolution-bits: + description: + Resolution of the digital output required by the application. This + determines the precision of the angle and/or the maximum speed that can + be measured. If resolution-gpios is omitted, it is assumed that RES0 and + RES1 are hard-wired to match this value. + enum: [10, 12, 14, 16] + +required: + - compatible + - reg + - spi-cpha + - avdd-supply + - dvdd-supply + - vdrive-supply + - clocks + - sample-gpios + - assigned-resolution-bits + +oneOf: + - required: + - mode-gpios + - required: + - adi,fixed-mode + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + resolver@0 { + compatible = "adi,ad2s1210"; + reg = <0>; + spi-max-frequency = <20000000>; + spi-cpha; + avdd-supply = <&avdd_regulator>; + dvdd-supply = <&dvdd_regulator>; + vdrive-supply = <&vdrive_regulator>; + clocks = <&ext_osc>; + sample-gpios = <&gpio0 90 GPIO_ACTIVE_LOW>; + mode-gpios = <&gpio0 86 0>, <&gpio0 87 0>; + resolution-gpios = <&gpio0 88 0>, <&gpio0 89 0>; + assigned-resolution-bits = <16>; + }; + }; |