diff options
Diffstat (limited to 'dts/Bindings/input/touchscreen')
21 files changed, 1214 insertions, 263 deletions
diff --git a/dts/Bindings/input/touchscreen/azoteq,iqs7211.yaml b/dts/Bindings/input/touchscreen/azoteq,iqs7211.yaml new file mode 100644 index 0000000000..8cf371b99f --- /dev/null +++ b/dts/Bindings/input/touchscreen/azoteq,iqs7211.yaml @@ -0,0 +1,769 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/azoteq,iqs7211.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Azoteq IQS7210A/7211A/E Trackpad/Touchscreen Controller + +maintainers: + - Jeff LaBundy <jeff@labundy.com> + +description: | + The Azoteq IQS7210A, IQS7211A and IQS7211E trackpad and touchscreen control- + lers employ projected-capacitance sensing and can track two contacts. + + Link to datasheets: https://www.azoteq.com/ + +properties: + compatible: + enum: + - azoteq,iqs7210a + - azoteq,iqs7211a + - azoteq,iqs7211e + + reg: + maxItems: 1 + + irq-gpios: + maxItems: 1 + description: + Specifies the GPIO connected to the device's active-low RDY output. The + pin doubles as the IQS7211E's active-low MCLR input, in which case this + GPIO must be configured as open-drain. + + reset-gpios: + maxItems: 1 + description: + Specifies the GPIO connected to the device's active-low MCLR input. The + device is temporarily held in hardware reset prior to initialization if + this property is present. + + azoteq,forced-comms: + type: boolean + description: + Enables forced communication; to be used with host adapters that cannot + tolerate clock stretching. + + azoteq,forced-comms-default: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: + Indicates if the device's OTP memory enables (1) or disables (0) forced + communication by default. Specifying this property can expedite startup + time if the default value is known. + + If this property is not specified, communication is not initiated until + the device asserts its RDY pin shortly after exiting hardware reset. At + that point, forced communication is either enabled or disabled based on + the presence or absence of the 'azoteq,forced-comms' property. + + azoteq,rate-active-ms: + minimum: 0 + maximum: 65535 + description: Specifies the report rate (in ms) during active mode. + + azoteq,rate-touch-ms: + minimum: 0 + maximum: 65535 + description: Specifies the report rate (in ms) during idle-touch mode. + + azoteq,rate-idle-ms: + minimum: 0 + maximum: 65535 + description: Specifies the report rate (in ms) during idle mode. + + azoteq,rate-lp1-ms: + minimum: 0 + maximum: 65535 + description: Specifies the report rate (in ms) during low-power mode 1. + + azoteq,rate-lp2-ms: + minimum: 0 + maximum: 65535 + description: Specifies the report rate (in ms) during low-power mode 2. + + azoteq,timeout-active-ms: + multipleOf: 1000 + minimum: 0 + maximum: 65535000 + description: + Specifies the length of time (in ms) to wait for an event before moving + from active mode to idle or idle-touch modes. + + azoteq,timeout-touch-ms: + multipleOf: 1000 + minimum: 0 + maximum: 65535000 + description: + Specifies the length of time (in ms) to wait for an event before moving + from idle-touch mode to idle mode. + + azoteq,timeout-idle-ms: + multipleOf: 1000 + minimum: 0 + maximum: 65535000 + description: + Specifies the length of time (in ms) to wait for an event before moving + from idle mode to low-power mode 1. + + azoteq,timeout-lp1-ms: + multipleOf: 1000 + minimum: 0 + maximum: 65535000 + description: + Specifies the length of time (in ms) to wait for an event before moving + from low-power mode 1 to low-power mode 2. + + azoteq,timeout-lp2-ms: + multipleOf: 1000 + minimum: 0 + maximum: 60000 + description: + Specifies the rate (in ms) at which the trackpad reference values + are updated during low-power modes 1 and 2. + + azoteq,timeout-ati-ms: + multipleOf: 1000 + minimum: 0 + maximum: 60000 + description: + Specifies the delay (in ms) before the automatic tuning implementation + (ATI) is retried in the event it fails to complete. + + azoteq,timeout-comms-ms: + minimum: 0 + maximum: 65535 + description: + Specifies the delay (in ms) before a communication window is closed. + + azoteq,timeout-press-ms: + multipleOf: 1000 + minimum: 0 + maximum: 60000 + description: + Specifies the length of time (in ms) to wait before automatically + releasing a press event. Specify zero to allow the press state to + persist indefinitely. + + azoteq,fosc-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + Specifies the device's core clock frequency as follows: + 0: 14 MHz + 1: 18 MHz + + azoteq,fosc-trim: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Specifies the device's core clock frequency trim. + + azoteq,num-contacts: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 2 + default: 0 + description: Specifies the number of contacts reported by the device. + + azoteq,contact-split: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the contact (finger) split factor. + + azoteq,trim-x: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the horizontal trim width. + + azoteq,trim-y: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the vertical trim height. + + trackpad: + type: object + description: Represents all channels associated with the trackpad. + + properties: + azoteq,rx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + description: + Specifies the order of the CRx pin(s) associated with the trackpad. + + azoteq,tx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 12 + items: + minimum: 0 + maximum: 11 + description: + Specifies the order of the CTx pin(s) associated with the trackpad. + + azoteq,channel-select: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 36 + items: + minimum: 0 + maximum: 255 + description: | + Specifies the channels mapped to each cycle in the following order: + Cycle 0, slot 0 + Cycle 0, slot 1 + Cycle 1, slot 0 + Cycle 1, slot 1 + ...and so on. Specify 255 to disable a given slot. + + azoteq,ati-frac-div-fine: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the trackpad's ATI fine fractional divider. + + azoteq,ati-frac-mult-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Specifies the trackpad's ATI coarse fractional multiplier. + + azoteq,ati-frac-div-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the trackpad's ATI coarse fractional divider. + + azoteq,ati-comp-div: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the trackpad's ATI compensation divider. + + azoteq,ati-target: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: Specifies the trackpad's ATI target. + + azoteq,touch-enter: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the trackpad's touch entrance factor. + + azoteq,touch-exit: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the trackpad's touch exit factor. + + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the trackpad's stationary touch threshold. + + azoteq,conv-period: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the trackpad's conversion period. + + azoteq,conv-frac: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the trackpad's conversion frequency fraction. + + patternProperties: + "^event-(tap(-double|-triple)?|hold|palm|swipe-(x|y)-(pos|neg)(-hold)?)$": + type: object + $ref: ../input.yaml# + description: + Represents a gesture event reported by the trackpad. In the case of + axial gestures, the duration or distance specified in one direction + applies to both directions along the same axis. + + properties: + linux,code: true + + azoteq,gesture-max-ms: + minimum: 0 + maximum: 65535 + description: Specifies the maximum duration of tap/swipe gestures. + + azoteq,gesture-mid-ms: + minimum: 0 + maximum: 65535 + description: + Specifies the maximum duration between subsequent tap gestures + (IQS7211E only). + + azoteq,gesture-min-ms: + minimum: 0 + maximum: 65535 + description: Specifies the minimum duration of hold gestures. + + azoteq,gesture-dist: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: + Specifies the minimum (swipe) or maximum (tap and hold) distance + a finger may travel to be considered a gesture. + + azoteq,gesture-dist-rep: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: + Specifies the minimum distance a finger must travel to elicit a + repeated swipe gesture (IQS7211E only). + + azoteq,gesture-angle: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 75 + description: + Specifies the maximum angle (in degrees) a finger may travel to + be considered a swipe gesture. + + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 42 + description: Specifies the palm gesture threshold (IQS7211E only). + + additionalProperties: false + + dependencies: + azoteq,rx-enable: ["azoteq,tx-enable"] + azoteq,tx-enable: ["azoteq,rx-enable"] + azoteq,channel-select: ["azoteq,rx-enable"] + + additionalProperties: false + + alp: + type: object + $ref: ../input.yaml# + description: Represents the alternate low-power channel (ALP). + + properties: + azoteq,rx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + description: + Specifies the CRx pin(s) associated with the ALP in no particular + order. + + azoteq,tx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 12 + items: + minimum: 0 + maximum: 11 + description: + Specifies the CTx pin(s) associated with the ALP in no particular + order. + + azoteq,ati-frac-div-fine: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the ALP's ATI fine fractional divider. + + azoteq,ati-frac-mult-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Specifies the ALP's ATI coarse fractional multiplier. + + azoteq,ati-frac-div-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the ALP's ATI coarse fractional divider. + + azoteq,ati-comp-div: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the ALP's ATI compensation divider. + + azoteq,ati-target: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: Specifies the ALP's ATI target. + + azoteq,ati-base: + $ref: /schemas/types.yaml#/definitions/uint32 + multipleOf: 8 + minimum: 0 + maximum: 255 + description: Specifies the ALP's ATI base. + + azoteq,ati-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + Specifies the ALP's ATI mode as follows: + 0: Partial + 1: Full + + azoteq,sense-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + Specifies the ALP's sensing mode as follows: + 0: Self capacitive + 1: Mutual capacitive + + azoteq,debounce-enter: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the ALP's debounce entrance factor. + + azoteq,debounce-exit: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the ALP's debounce exit factor. + + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: Specifies the ALP's proximity or touch threshold. + + azoteq,conv-period: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the ALP's conversion period. + + azoteq,conv-frac: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the ALP's conversion frequency fraction. + + linux,code: true + + additionalProperties: false + + button: + type: object + description: Represents the inductive or capacitive button. + + properties: + azoteq,ati-frac-div-fine: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the button's ATI fine fractional divider. + + azoteq,ati-frac-mult-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Specifies the button's ATI coarse fractional multiplier. + + azoteq,ati-frac-div-coarse: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the button's ATI coarse fractional divider. + + azoteq,ati-comp-div: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Specifies the button's ATI compensation divider. + + azoteq,ati-target: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: Specifies the button's ATI target. + + azoteq,ati-base: + $ref: /schemas/types.yaml#/definitions/uint32 + multipleOf: 8 + minimum: 0 + maximum: 255 + description: Specifies the button's ATI base. + + azoteq,ati-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + Specifies the button's ATI mode as follows: + 0: Partial + 1: Full + + azoteq,sense-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + description: | + Specifies the button's sensing mode as follows: + 0: Self capacitive + 1: Mutual capacitive + 2: Inductive + + azoteq,touch-enter: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the button's touch entrance factor. + + azoteq,touch-exit: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the button's touch exit factor. + + azoteq,debounce-enter: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the button's debounce entrance factor. + + azoteq,debounce-exit: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the button's debounce exit factor. + + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 65535 + description: Specifies the button's proximity threshold. + + azoteq,conv-period: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the button's conversion period. + + azoteq,conv-frac: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the button's conversion frequency fraction. + + patternProperties: + "^event-(prox|touch)$": + type: object + $ref: ../input.yaml# + description: + Represents a proximity or touch event reported by the button. + + properties: + linux,code: true + + additionalProperties: false + + additionalProperties: false + + wakeup-source: true + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + +dependencies: + touchscreen-size-x: ["azoteq,num-contacts"] + touchscreen-size-y: ["azoteq,num-contacts"] + touchscreen-inverted-x: ["azoteq,num-contacts"] + touchscreen-inverted-y: ["azoteq,num-contacts"] + touchscreen-swapped-x-y: ["azoteq,num-contacts"] + +required: + - compatible + - reg + - irq-gpios + +additionalProperties: false + +allOf: + - $ref: touchscreen.yaml# + + - if: + properties: + compatible: + contains: + const: azoteq,iqs7210a + + then: + properties: + alp: + properties: + azoteq,rx-enable: + maxItems: 4 + items: + minimum: 4 + + else: + properties: + azoteq,timeout-press-ms: false + + alp: + properties: + azoteq,ati-mode: false + + button: false + + - if: + properties: + compatible: + contains: + const: azoteq,iqs7211e + + then: + properties: + reset-gpios: false + + trackpad: + properties: + azoteq,tx-enable: + maxItems: 13 + items: + maximum: 12 + + alp: + properties: + azoteq,tx-enable: + maxItems: 13 + items: + maximum: 12 + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/input/input.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touch@56 { + compatible = "azoteq,iqs7210a"; + reg = <0x56>; + irq-gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio 17 (GPIO_ACTIVE_LOW | + GPIO_PUSH_PULL)>; + azoteq,num-contacts = <2>; + + trackpad { + azoteq,rx-enable = <6>, <5>, <4>, <3>, <2>; + azoteq,tx-enable = <1>, <7>, <8>, <9>, <10>; + }; + + button { + azoteq,sense-mode = <2>; + azoteq,touch-enter = <40>; + azoteq,touch-exit = <36>; + + event-touch { + linux,code = <KEY_HOME>; + }; + }; + + alp { + azoteq,sense-mode = <1>; + linux,code = <KEY_POWER>; + }; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/input/input.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touch@56 { + compatible = "azoteq,iqs7211e"; + reg = <0x56>; + irq-gpios = <&gpio 4 (GPIO_ACTIVE_LOW | + GPIO_OPEN_DRAIN)>; + + trackpad { + event-tap { + linux,code = <KEY_PLAYPAUSE>; + }; + + event-tap-double { + linux,code = <KEY_SHUFFLE>; + }; + + event-tap-triple { + linux,code = <KEY_AGAIN>; + }; + + event-hold { + linux,code = <KEY_STOP>; + }; + + event-palm { + linux,code = <KEY_EXIT>; + }; + + event-swipe-x-pos { + linux,code = <KEY_REWIND>; + }; + + event-swipe-x-pos-hold { + linux,code = <KEY_PREVIOUS>; + }; + + event-swipe-x-neg { + linux,code = <KEY_FASTFORWARD>; + }; + + event-swipe-x-neg-hold { + linux,code = <KEY_NEXT>; + }; + + event-swipe-y-pos { + linux,code = <KEY_VOLUMEUP>; + }; + + event-swipe-y-pos-hold { + linux,code = <KEY_MUTE>; + }; + + event-swipe-y-neg { + linux,code = <KEY_VOLUMEDOWN>; + }; + + event-swipe-y-neg-hold { + linux,code = <KEY_MUTE>; + }; + }; + }; + }; + +... diff --git a/dts/Bindings/input/touchscreen/cypress,tt21000.yaml b/dts/Bindings/input/touchscreen/cypress,tt21000.yaml index 1959ec3947..037e5d3c44 100644 --- a/dts/Bindings/input/touchscreen/cypress,tt21000.yaml +++ b/dts/Bindings/input/touchscreen/cypress,tt21000.yaml @@ -34,12 +34,17 @@ properties: vdd-supply: description: Regulator for voltage. + vddio-supply: + description: Optional Regulator for I/O voltage. + reset-gpios: maxItems: 1 linux,keycodes: description: EV_ABS specific event code generated by the axis. + wakeup-source: true + patternProperties: "^button@[0-9]+$": type: object diff --git a/dts/Bindings/input/touchscreen/edt-ft5x06.yaml b/dts/Bindings/input/touchscreen/edt-ft5x06.yaml index ef4c841387..f2808cb4d9 100644 --- a/dts/Bindings/input/touchscreen/edt-ft5x06.yaml +++ b/dts/Bindings/input/touchscreen/edt-ft5x06.yaml @@ -93,6 +93,12 @@ properties: minimum: 1 maximum: 255 + threshold: + description: Allows setting the "click"-threshold in the range from 0 to 255. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + touchscreen-size-x: true touchscreen-size-y: true touchscreen-fuzz-x: true diff --git a/dts/Bindings/input/touchscreen/eeti,exc3000.yaml b/dts/Bindings/input/touchscreen/eeti,exc3000.yaml index 007adbc89c..9dc25d30a0 100644 --- a/dts/Bindings/input/touchscreen/eeti,exc3000.yaml +++ b/dts/Bindings/input/touchscreen/eeti,exc3000.yaml @@ -24,6 +24,8 @@ properties: maxItems: 1 reset-gpios: maxItems: 1 + vdd-supply: + description: Power supply regulator for the chip touchscreen-size-x: true touchscreen-size-y: true touchscreen-inverted-x: true diff --git a/dts/Bindings/input/touchscreen/elan,elants_i2c.yaml b/dts/Bindings/input/touchscreen/elan,elants_i2c.yaml index f9053e5e9b..3255c2c895 100644 --- a/dts/Bindings/input/touchscreen/elan,elants_i2c.yaml +++ b/dts/Bindings/input/touchscreen/elan,elants_i2c.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/input/touchscreen/elan,elants_i2c.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/input/touchscreen/elan,elants_i2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Elantech I2C Touchscreen diff --git a/dts/Bindings/input/touchscreen/fsl,imx6ul-tsc.yaml b/dts/Bindings/input/touchscreen/fsl,imx6ul-tsc.yaml new file mode 100644 index 0000000000..678756ad0f --- /dev/null +++ b/dts/Bindings/input/touchscreen/fsl,imx6ul-tsc.yaml @@ -0,0 +1,97 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/fsl,imx6ul-tsc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale i.MX6UL Touch Controller + +maintainers: + - Haibo Chen <haibo.chen@nxp.com> + - Shawn Guo <shawnguo@kernel.org> + - Sascha Hauer <s.hauer@pengutronix.de> + +properties: + compatible: + const: fsl,imx6ul-tsc + + reg: + items: + - description: touch controller address + - description: ADC2 address + + interrupts: + items: + - description: touch controller address + - description: ADC2 address + + clocks: + maxItems: 2 + + clock-names: + items: + - const: tsc + - const: adc + + xnur-gpios: + maxItems: 1 + description: + The X- gpio this controller connect to. This xnur-gpio returns to + low once the finger leave the touch screen (The last touch event + the touch controller capture). + + measure-delay-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The value of measure delay time. Before X-axis or Y-axis measurement, + the screen need some time before even potential distribution ready. + default: 0xffff + minimum: 0 + maximum: 0xffffff + + pre-charge-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The touch screen need some time to precharge. + default: 0xfff + minimum: 0 + maximum: 0xffffffff + + touchscreen-average-samples: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Number of data samples which are averaged for each read. + enum: [ 1, 4, 8, 16, 32 ] + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - xnur-gpios + +allOf: + - $ref: touchscreen.yaml# + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/imx6ul-clock.h> + #include <dt-bindings/gpio/gpio.h> + touchscreen@2040000 { + compatible = "fsl,imx6ul-tsc"; + reg = <0x02040000 0x4000>, <0x0219c000 0x4000>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6UL_CLK_IPG>, + <&clks IMX6UL_CLK_ADC2>; + clock-names = "tsc", "adc"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc>; + xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; + measure-delay-time = <0xfff>; + pre-charge-time = <0xffff>; + touchscreen-average-samples = <32>; + }; diff --git a/dts/Bindings/input/touchscreen/goodix,gt9916.yaml b/dts/Bindings/input/touchscreen/goodix,gt9916.yaml new file mode 100644 index 0000000000..d90f045ac0 --- /dev/null +++ b/dts/Bindings/input/touchscreen/goodix,gt9916.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/goodix,gt9916.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Goodix Berlin series touchscreen controller + +description: The Goodix Berlin series of touchscreen controllers + be connected to either I2C or SPI buses. + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +allOf: + - $ref: touchscreen.yaml# + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +properties: + compatible: + enum: + - goodix,gt9916 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + avdd-supply: + description: Analog power supply regulator on AVDD pin + + vddio-supply: + description: power supply regulator on VDDIO pin + + spi-max-frequency: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-swapped-x-y: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - avdd-supply + - touchscreen-size-x + - touchscreen-size-y + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@5d { + compatible = "goodix,gt9916"; + reg = <0x5d>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + avdd-supply = <&ts_avdd>; + touchscreen-size-x = <1024>; + touchscreen-size-y = <768>; + }; + }; + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + num-cs = <1>; + cs-gpios = <&gpio 2 GPIO_ACTIVE_HIGH>; + touchscreen@0 { + compatible = "goodix,gt9916"; + reg = <0>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + avdd-supply = <&ts_avdd>; + spi-max-frequency = <1000000>; + touchscreen-size-x = <1024>; + touchscreen-size-y = <768>; + }; + }; + +... diff --git a/dts/Bindings/input/touchscreen/goodix.yaml b/dts/Bindings/input/touchscreen/goodix.yaml index 3d016b87c8..2a2d86cfd1 100644 --- a/dts/Bindings/input/touchscreen/goodix.yaml +++ b/dts/Bindings/input/touchscreen/goodix.yaml @@ -37,8 +37,9 @@ properties: maxItems: 1 irq-gpios: - description: GPIO pin used for IRQ. The driver uses the interrupt gpio pin - as output to reset the device. + description: GPIO pin used for IRQ input. Additionally, this line is + sampled by the device on reset deassertion to select the I2C client + address, thus it can be driven by the host during the reset sequence. maxItems: 1 reset-gpios: diff --git a/dts/Bindings/input/touchscreen/imagis,ist3038c.yaml b/dts/Bindings/input/touchscreen/imagis,ist3038c.yaml index 0d6b033fd5..77ba280b3b 100644 --- a/dts/Bindings/input/touchscreen/imagis,ist3038c.yaml +++ b/dts/Bindings/input/touchscreen/imagis,ist3038c.yaml @@ -9,15 +9,14 @@ title: Imagis IST30XXC family touchscreen controller maintainers: - Markuss Broks <markuss.broks@gmail.com> -allOf: - - $ref: touchscreen.yaml# - properties: $nodename: pattern: "^touchscreen@[0-9a-f]+$" compatible: enum: + - imagis,ist3032c + - imagis,ist3038b - imagis,ist3038c reg: @@ -32,6 +31,10 @@ properties: vddio-supply: description: Power supply regulator for the I2C bus + linux,keycodes: + description: Keycodes for the touch keys + maxItems: 5 + touchscreen-size-x: true touchscreen-size-y: true touchscreen-fuzz-x: true @@ -42,6 +45,18 @@ properties: additionalProperties: false +allOf: + - $ref: touchscreen.yaml# + - if: + not: + properties: + compatible: + contains: + const: imagis,ist3032c + then: + properties: + linux,keycodes: false + required: - compatible - reg diff --git a/dts/Bindings/input/touchscreen/imx6ul_tsc.txt b/dts/Bindings/input/touchscreen/imx6ul_tsc.txt deleted file mode 100644 index 1649150044..0000000000 --- a/dts/Bindings/input/touchscreen/imx6ul_tsc.txt +++ /dev/null @@ -1,38 +0,0 @@ -* Freescale i.MX6UL Touch Controller - -Required properties: -- compatible: must be "fsl,imx6ul-tsc". -- reg: this touch controller address and the ADC2 address. -- interrupts: the interrupt of this touch controller and ADC2. -- clocks: the root clock of touch controller and ADC2. -- clock-names; must be "tsc" and "adc". -- xnur-gpio: the X- gpio this controller connect to. - This xnur-gpio returns to low once the finger leave the touch screen (The - last touch event the touch controller capture). - -Optional properties: -- measure-delay-time: the value of measure delay time. - Before X-axis or Y-axis measurement, the screen need some time before - even potential distribution ready. - This value depends on the touch screen. -- pre-charge-time: the touch screen need some time to precharge. - This value depends on the touch screen. -- touchscreen-average-samples: Number of data samples which are averaged for - each read. Valid values are 1, 4, 8, 16 and 32. - -Example: - tsc: tsc@2040000 { - compatible = "fsl,imx6ul-tsc"; - reg = <0x02040000 0x4000>, <0x0219c000 0x4000>; - interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clks IMX6UL_CLK_IPG>, - <&clks IMX6UL_CLK_ADC2>; - clock-names = "tsc", "adc"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_tsc>; - xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; - measure-delay-time = <0xfff>; - pre-charge-time = <0xffff>; - touchscreen-average-samples = <32>; - }; diff --git a/dts/Bindings/input/touchscreen/melfas,mms114.yaml b/dts/Bindings/input/touchscreen/melfas,mms114.yaml index fdd02898e2..90ebd4f835 100644 --- a/dts/Bindings/input/touchscreen/melfas,mms114.yaml +++ b/dts/Bindings/input/touchscreen/melfas,mms114.yaml @@ -17,13 +17,17 @@ properties: pattern: "^touchscreen(@.*)?$" compatible: - items: + oneOf: - enum: - melfas,mms114 - melfas,mms134s - melfas,mms136 - melfas,mms152 - melfas,mms345l + - items: + - enum: + - melfas,mms252 + - const: melfas,mms114 reg: description: I2C address @@ -52,6 +56,11 @@ properties: touchscreen-swapped-x-y: true touchscreen-max-pressure: true + linux,keycodes: + description: Keycodes for the touch keys + minItems: 1 + maxItems: 15 + additionalProperties: false required: diff --git a/dts/Bindings/input/touchscreen/neonode,zforce.yaml b/dts/Bindings/input/touchscreen/neonode,zforce.yaml new file mode 100644 index 0000000000..c2ee89b76e --- /dev/null +++ b/dts/Bindings/input/touchscreen/neonode,zforce.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/neonode,zforce.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Neonode infrared touchscreen controller + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + const: neonode,zforce + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + irq-gpios: + maxItems: 1 + + x-size: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + + y-size: + deprecated: true + $ref: /schemas/types.yaml#/definitions/uint32 + + vdd-supply: true + +required: + - compatible + - reg + - interrupts + - reset-gpios + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@50 { + compatible = "neonode,zforce"; + reg = <0x50>; + interrupts = <2 0>; + vdd-supply = <®_zforce_vdd>; + + reset-gpios = <&gpio5 9 0>; /* RST */ + irq-gpios = <&gpio5 6 0>; /* IRQ, optional */ + + touchscreen-min-x = <0>; + touchscreen-size-x = <800>; + touchscreen-min-y = <0>; + touchscreen-size-y = <600>; + }; + }; +... diff --git a/dts/Bindings/input/touchscreen/samsung,s6sy761.txt b/dts/Bindings/input/touchscreen/samsung,s6sy761.txt deleted file mode 100644 index 6805d10d22..0000000000 --- a/dts/Bindings/input/touchscreen/samsung,s6sy761.txt +++ /dev/null @@ -1,32 +0,0 @@ -* Samsung S6SY761 touchscreen controller - -Required properties: -- compatible : must be "samsung,s6sy761" -- reg : I2C slave address, (e.g. 0x48) -- interrupts : interrupt specification -- avdd-supply : analogic power supply -- vdd-supply : power supply - -Optional properties: -- touchscreen-size-x : see touchscreen.txt. This property is embedded in the - device. If defined it forces a different x resolution. -- touchscreen-size-y : see touchscreen.txt. This property is embedded in the - device. If defined it forces a different y resolution. - -Example: - -i2c@00000000 { - - /* ... */ - - touchscreen@48 { - compatible = "samsung,s6sy761"; - reg = <0x48>; - interrupt-parent = <&gpa1>; - interrupts = <1 IRQ_TYPE_NONE>; - avdd-supply = <&ldo30_reg>; - vdd-supply = <&ldo31_reg>; - touchscreen-size-x = <4096>; - touchscreen-size-y = <4096>; - }; -}; diff --git a/dts/Bindings/input/touchscreen/samsung,s6sy761.yaml b/dts/Bindings/input/touchscreen/samsung,s6sy761.yaml new file mode 100644 index 0000000000..1ffd17af3c --- /dev/null +++ b/dts/Bindings/input/touchscreen/samsung,s6sy761.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/samsung,s6sy761.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S6SY761 touchscreen controller + +maintainers: + - Andi Shyti <andi.shyti@kernel.org> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + const: samsung,s6sy761 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + avdd-supply: true + vdd-supply: true + +unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - avdd-supply + - vdd-supply + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@48 { + compatible = "samsung,s6sy761"; + reg = <0x48>; + interrupt-parent = <&gpa1>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH>; + avdd-supply = <&ldo30_reg>; + vdd-supply = <&ldo31_reg>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + }; + }; diff --git a/dts/Bindings/input/touchscreen/silead,gsl1680.yaml b/dts/Bindings/input/touchscreen/silead,gsl1680.yaml index 95b554be25..5381a96f49 100644 --- a/dts/Bindings/input/touchscreen/silead,gsl1680.yaml +++ b/dts/Bindings/input/touchscreen/silead,gsl1680.yaml @@ -31,7 +31,7 @@ properties: maxItems: 1 firmware-name: - $ref: /schemas/types.yaml#/definitions/string + maxItems: 1 description: > File basename for board specific firmware diff --git a/dts/Bindings/input/touchscreen/st,stmfts.txt b/dts/Bindings/input/touchscreen/st,stmfts.txt deleted file mode 100644 index 0a5d0cb4a2..0000000000 --- a/dts/Bindings/input/touchscreen/st,stmfts.txt +++ /dev/null @@ -1,41 +0,0 @@ -* ST-Microelectronics FingerTip touchscreen controller - -The ST-Microelectronics FingerTip device provides a basic touchscreen -functionality. Along with it the user can enable the touchkey which can work as -a basic HOME and BACK key for phones. - -The driver supports also hovering as an absolute single touch event with x, y, z -coordinates. - -Required properties: -- compatible : must be "st,stmfts" -- reg : I2C slave address, (e.g. 0x49) -- interrupts : interrupt specification -- avdd-supply : analogic power supply -- vdd-supply : power supply -- touchscreen-size-x : see touchscreen.txt -- touchscreen-size-y : see touchscreen.txt - -Optional properties: -- touch-key-connected : specifies whether the touchkey feature is connected -- ledvdd-supply : power supply to the touch key leds - -Example: - -i2c@00000000 { - - /* ... */ - - touchscreen@49 { - compatible = "st,stmfts"; - reg = <0x49>; - interrupt-parent = <&gpa1>; - interrupts = <1 IRQ_TYPE_NONE>; - touchscreen-size-x = <1599>; - touchscreen-size-y = <2559>; - touch-key-connected; - avdd-supply = <&ldo30_reg>; - vdd-supply = <&ldo31_reg>; - ledvdd-supply = <&ldo33_reg>; - }; -}; diff --git a/dts/Bindings/input/touchscreen/st,stmfts.yaml b/dts/Bindings/input/touchscreen/st,stmfts.yaml new file mode 100644 index 0000000000..c593ae63d0 --- /dev/null +++ b/dts/Bindings/input/touchscreen/st,stmfts.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/st,stmfts.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ST-Microelectronics FingerTip touchscreen controller + +maintainers: + - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> + +description: + The ST-Microelectronics FingerTip device provides a basic touchscreen + functionality. Along with it the user can enable the touchkey which can work + as a basic HOME and BACK key for phones. + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + const: st,stmfts + + reg: + maxItems: 1 + + avdd-supply: + description: Analogic power supply + + interrupts: + maxItems: 1 + + ledvdd-supply: + description: Power supply to the touch key leds + + touch-key-connected: + type: boolean + description: The touchkey feature is connected + + vdd-supply: + description: Power supply + +required: + - compatible + - reg + - avdd-supply + - interrupts + - vdd-supply + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@49 { + compatible = "st,stmfts"; + reg = <0x49>; + interrupt-parent = <&gpa1>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + touchscreen-size-x = <1599>; + touchscreen-size-y = <2559>; + touch-key-connected; + avdd-supply = <&ldo30_reg>; + vdd-supply = <&ldo31_reg>; + ledvdd-supply = <&ldo33_reg>; + }; + }; diff --git a/dts/Bindings/input/touchscreen/stmpe.txt b/dts/Bindings/input/touchscreen/stmpe.txt deleted file mode 100644 index 238b51555c..0000000000 --- a/dts/Bindings/input/touchscreen/stmpe.txt +++ /dev/null @@ -1,108 +0,0 @@ -STMPE Touchscreen ----------------- - -Required properties: - - compatible: "st,stmpe-ts" - -Optional properties: -- st,ave-ctrl : Sample average control - 0 -> 1 sample - 1 -> 2 samples - 2 -> 4 samples - 3 -> 8 samples -- st,touch-det-delay : Touch detect interrupt delay (recommended is 3) - 0 -> 10 us - 1 -> 50 us - 2 -> 100 us - 3 -> 500 us - 4 -> 1 ms - 5 -> 5 ms - 6 -> 10 ms - 7 -> 50 ms -- st,settling : Panel driver settling time (recommended is 2) - 0 -> 10 us - 1 -> 100 us - 2 -> 500 us - 3 -> 1 ms - 4 -> 5 ms - 5 -> 10 ms - 6 -> 50 ms - 7 -> 100 ms -- st,fraction-z : Length of the fractional part in z (recommended is 7) - (fraction-z ([0..7]) = Count of the fractional part) -- st,i-drive : current limit value of the touchscreen drivers - 0 -> 20 mA (typical 35mA max) - 1 -> 50 mA (typical 80 mA max) - -Optional properties common with MFD (deprecated): - - st,sample-time : ADC conversion time in number of clock. - 0 -> 36 clocks - 1 -> 44 clocks - 2 -> 56 clocks - 3 -> 64 clocks - 4 -> 80 clocks (recommended) - 5 -> 96 clocks - 6 -> 124 clocks - - st,mod-12b : ADC Bit mode - 0 -> 10bit ADC - 1 -> 12bit ADC - - st,ref-sel : ADC reference source - 0 -> internal - 1 -> external - - st,adc-freq : ADC Clock speed - 0 -> 1.625 MHz - 1 -> 3.25 MHz - 2 || 3 -> 6.5 MHz - -Node should be child node of stmpe node to which it belongs. - -Note that common ADC settings of stmpe_touchscreen (child) will take precedence -over the settings done in MFD. - -Example: - -stmpe811@41 { - compatible = "st,stmpe811"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_touch_int>; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x41>; - interrupts = <10 IRQ_TYPE_LEVEL_LOW>; - interrupt-parent = <&gpio4>; - interrupt-controller; - id = <0>; - blocks = <0x5>; - irq-trigger = <0x1>; - /* Common ADC settings */ - /* 3.25 MHz ADC clock speed */ - st,adc-freq = <1>; - /* 12-bit ADC */ - st,mod-12b = <1>; - /* internal ADC reference */ - st,ref-sel = <0>; - /* ADC converstion time: 80 clocks */ - st,sample-time = <4>; - - stmpe_touchscreen { - compatible = "st,stmpe-ts"; - reg = <0>; - /* 8 sample average control */ - st,ave-ctrl = <3>; - /* 5 ms touch detect interrupt delay */ - st,touch-det-delay = <5>; - /* 1 ms panel driver settling time */ - st,settling = <3>; - /* 7 length fractional part in z */ - st,fraction-z = <7>; - /* - * 50 mA typical 80 mA max touchscreen drivers - * current limit value - */ - st,i-drive = <1>; - }; - stmpe_adc { - compatible = "st,stmpe-adc"; - st,norequest-mask = <0x0F>; - }; -}; diff --git a/dts/Bindings/input/touchscreen/touchscreen.yaml b/dts/Bindings/input/touchscreen/touchscreen.yaml index 895592da96..431c13335c 100644 --- a/dts/Bindings/input/touchscreen/touchscreen.yaml +++ b/dts/Bindings/input/touchscreen/touchscreen.yaml @@ -10,6 +10,13 @@ maintainers: - Dmitry Torokhov <dmitry.torokhov@gmail.com> properties: + panel: + description: If this touchscreen is integrally connected to a panel, this + is a reference to that panel. The presence of this reference indicates + that the touchscreen should be power sequenced together with the panel + and that they may share power and/or reset signals. + $ref: /schemas/types.yaml#/definitions/phandle + touchscreen-min-x: description: minimum x coordinate reported $ref: /schemas/types.yaml#/definitions/uint32 diff --git a/dts/Bindings/input/touchscreen/tsc2007.txt b/dts/Bindings/input/touchscreen/tsc2007.txt index ed00f61b8c..210486a3fb 100644 --- a/dts/Bindings/input/touchscreen/tsc2007.txt +++ b/dts/Bindings/input/touchscreen/tsc2007.txt @@ -6,7 +6,7 @@ Required properties: - ti,x-plate-ohms: X-plate resistance in ohms. Optional properties: -- gpios: the interrupt gpio the chip is connected to (trough the penirq pin). +- gpios: the interrupt gpio the chip is connected to (through the penirq pin). The penirq pin goes to low when the panel is touched. (see GPIO binding[1] for more details). - interrupts: (gpio) interrupt to which the chip is connected diff --git a/dts/Bindings/input/touchscreen/zforce_ts.txt b/dts/Bindings/input/touchscreen/zforce_ts.txt deleted file mode 100644 index e3c27c4fd9..0000000000 --- a/dts/Bindings/input/touchscreen/zforce_ts.txt +++ /dev/null @@ -1,34 +0,0 @@ -* Neonode infrared touchscreen controller - -Required properties: -- compatible: must be "neonode,zforce" -- reg: I2C address of the chip -- interrupts: interrupt to which the chip is connected -- reset-gpios: reset gpio the chip is connected to -- x-size: horizontal resolution of touchscreen -- y-size: vertical resolution of touchscreen - -Optional properties: -- irq-gpios : interrupt gpio the chip is connected to -- vdd-supply: Regulator controlling the controller supply - -Example: - - i2c@00000000 { - /* ... */ - - zforce_ts@50 { - compatible = "neonode,zforce"; - reg = <0x50>; - interrupts = <2 0>; - vdd-supply = <®_zforce_vdd>; - - reset-gpios = <&gpio5 9 0>; /* RST */ - irq-gpios = <&gpio5 6 0>; /* IRQ, optional */ - - x-size = <800>; - y-size = <600>; - }; - - /* ... */ - }; |