summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/media/i2c/st,st-mipid02.txt
diff options
context:
space:
mode:
Diffstat (limited to 'dts/Bindings/media/i2c/st,st-mipid02.txt')
-rw-r--r--dts/Bindings/media/i2c/st,st-mipid02.txt82
1 files changed, 82 insertions, 0 deletions
diff --git a/dts/Bindings/media/i2c/st,st-mipid02.txt b/dts/Bindings/media/i2c/st,st-mipid02.txt
new file mode 100644
index 0000000..7976e6c
--- /dev/null
+++ b/dts/Bindings/media/i2c/st,st-mipid02.txt
@@ -0,0 +1,82 @@
+STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge
+
+MIPID02 has two CSI-2 input ports, only one of those ports can be active at a
+time. Active port input stream will be de-serialized and its content outputted
+through PARALLEL output port.
+CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 second
+input port is a single lane 800Mbps. Both ports support clock and data lane
+polarity swap. First port also supports data lane swap.
+PARALLEL output port has a maximum width of 12 bits.
+Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, RGB444,
+YUV420 8-bit, YUV422 8-bit and YUV420 10-bit.
+
+Required Properties:
+- compatible: shall be "st,st-mipid02"
+- clocks: reference to the xclk input clock.
+- clock-names: shall be "xclk".
+- VDDE-supply: sensor digital IO supply. Must be 1.8 volts.
+- VDDIN-supply: sensor internal regulator supply. Must be 1.8 volts.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the xsdn pin, if any.
+ This is an active low signal to the mipid02.
+
+Required subnodes:
+ - ports: A ports node with one port child node per device input and output
+ port, in accordance with the video interface bindings defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt. The
+ port nodes are numbered as follows:
+
+ Port Description
+ -----------------------------
+ 0 CSI-2 first input port
+ 1 CSI-2 second input port
+ 2 PARALLEL output
+
+Endpoint node required property for CSI-2 connection is:
+- data-lanes: shall be <1> for Port 1. for Port 0 dual-lane operation shall be
+<1 2> or <2 1>. For Port 0 single-lane operation shall be <1> or <2>.
+Endpoint node optional property for CSI-2 connection is:
+- lane-polarities: any lane can be inverted or not.
+
+Endpoint node required property for PARALLEL connection is:
+- bus-width: shall be set to <6>, <7>, <8>, <10> or <12>.
+Endpoint node optional properties for PARALLEL connection are:
+- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
+LOW being the default.
+- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
+LOW being the default.
+
+Example:
+
+mipid02: csi2rx@14 {
+ compatible = "st,st-mipid02";
+ reg = <0x14>;
+ status = "okay";
+ clocks = <&clk_ext_camera_12>;
+ clock-names = "xclk";
+ VDDE-supply = <&vdd>;
+ VDDIN-supply = <&vdd>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+
+ ep0: endpoint {
+ data-lanes = <1 2>;
+ remote-endpoint = <&mipi_csi2_in>;
+ };
+ };
+ port@2 {
+ reg = <2>;
+
+ ep2: endpoint {
+ bus-width = <8>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ remote-endpoint = <&parallel_out>;
+ };
+ };
+ };
+};