diff options
Diffstat (limited to 'dts/Bindings/mtd')
-rw-r--r-- | dts/Bindings/mtd/amlogic,meson-nand.txt | 60 | ||||
-rw-r--r-- | dts/Bindings/mtd/cadence-quadspi.txt | 1 | ||||
-rw-r--r-- | dts/Bindings/mtd/fsl-quadspi.txt | 65 | ||||
-rw-r--r-- | dts/Bindings/mtd/mtk-quadspi.txt | 3 | ||||
-rw-r--r-- | dts/Bindings/mtd/stm32-fmc2-nand.txt | 61 |
5 files changed, 124 insertions, 66 deletions
diff --git a/dts/Bindings/mtd/amlogic,meson-nand.txt b/dts/Bindings/mtd/amlogic,meson-nand.txt new file mode 100644 index 0000000000..3983c11e06 --- /dev/null +++ b/dts/Bindings/mtd/amlogic,meson-nand.txt @@ -0,0 +1,60 @@ +Amlogic NAND Flash Controller (NFC) for GXBB/GXL/AXG family SoCs + +This file documents the properties in addition to those available in +the MTD NAND bindings. + +Required properties: +- compatible : contains one of: + - "amlogic,meson-gxl-nfc" + - "amlogic,meson-axg-nfc" +- clocks : + A list of phandle + clock-specifier pairs for the clocks listed + in clock-names. + +- clock-names: Should contain the following: + "core" - NFC module gate clock + "device" - device clock from eMMC sub clock controller + "rx" - rx clock phase + "tx" - tx clock phase + +- amlogic,mmc-syscon : Required for NAND clocks, it's shared with SD/eMMC + controller port C + +Optional children nodes: +Children nodes represent the available nand chips. + +Other properties: +see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings. + +Example demonstrate on AXG SoC: + + sd_emmc_c_clkc: mmc@7000 { + compatible = "amlogic,meson-axg-mmc-clkc", "syscon"; + reg = <0x0 0x7000 0x0 0x800>; + }; + + nand-controller@7800 { + compatible = "amlogic,meson-axg-nfc"; + reg = <0x0 0x7800 0x0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>; + + clocks = <&clkc CLKID_SD_EMMC_C>, + <&sd_emmc_c_clkc CLKID_MMC_DIV>, + <&sd_emmc_c_clkc CLKID_MMC_PHASE_RX>, + <&sd_emmc_c_clkc CLKID_MMC_PHASE_TX>; + clock-names = "core", "device", "rx", "tx"; + amlogic,mmc-syscon = <&sd_emmc_c_clkc>; + + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins>; + + nand@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + + nand-on-flash-bbt; + }; + }; diff --git a/dts/Bindings/mtd/cadence-quadspi.txt b/dts/Bindings/mtd/cadence-quadspi.txt index bb2075df9b..4345c3a6f5 100644 --- a/dts/Bindings/mtd/cadence-quadspi.txt +++ b/dts/Bindings/mtd/cadence-quadspi.txt @@ -4,6 +4,7 @@ Required properties: - compatible : should be one of the following: Generic default - "cdns,qspi-nor". For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor". + For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor". - reg : Contains two entries, each of which is a tuple consisting of a physical address and length. The first entry is the address and length of the controller register set. The second entry is the diff --git a/dts/Bindings/mtd/fsl-quadspi.txt b/dts/Bindings/mtd/fsl-quadspi.txt deleted file mode 100644 index 483e9cfac1..0000000000 --- a/dts/Bindings/mtd/fsl-quadspi.txt +++ /dev/null @@ -1,65 +0,0 @@ -* Freescale Quad Serial Peripheral Interface(QuadSPI) - -Required properties: - - compatible : Should be "fsl,vf610-qspi", "fsl,imx6sx-qspi", - "fsl,imx7d-qspi", "fsl,imx6ul-qspi", - "fsl,ls1021a-qspi" - or - "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi", - "fsl,ls1043a-qspi" followed by "fsl,ls1021a-qspi" - - reg : the first contains the register location and length, - the second contains the memory mapping address and length - - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory" - - interrupts : Should contain the interrupt for the device - - clocks : The clocks needed by the QuadSPI controller - - clock-names : Should contain the name of the clocks: "qspi_en" and "qspi". - -Optional properties: - - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B. - Each bus can be connected with two NOR flashes. - Most of the time, each bus only has one NOR flash - connected, this is the default case. - But if there are two NOR flashes connected to the - bus, you should enable this property. - (Please check the board's schematic.) - - big-endian : That means the IP register is big endian - -Example: - -qspi0: quadspi@40044000 { - compatible = "fsl,vf610-qspi"; - reg = <0x40044000 0x1000>, <0x20000000 0x10000000>; - reg-names = "QuadSPI", "QuadSPI-memory"; - interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clks VF610_CLK_QSPI0_EN>, - <&clks VF610_CLK_QSPI0>; - clock-names = "qspi_en", "qspi"; - - flash0: s25fl128s@0 { - .... - }; -}; - -Example showing the usage of two SPI NOR devices: - -&qspi2 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_qspi2>; - status = "okay"; - - flash0: n25q256a@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "micron,n25q256a", "jedec,spi-nor"; - spi-max-frequency = <29000000>; - reg = <0>; - }; - - flash1: n25q256a@1 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "micron,n25q256a", "jedec,spi-nor"; - spi-max-frequency = <29000000>; - reg = <1>; - }; -}; diff --git a/dts/Bindings/mtd/mtk-quadspi.txt b/dts/Bindings/mtd/mtk-quadspi.txt index 56d3668e2c..a12e3b5c49 100644 --- a/dts/Bindings/mtd/mtk-quadspi.txt +++ b/dts/Bindings/mtd/mtk-quadspi.txt @@ -1,4 +1,4 @@ -* Serial NOR flash controller for MTK MT81xx (and similar) +* Serial NOR flash controller for MediaTek SoCs Required properties: - compatible: For mt8173, compatible should be "mediatek,mt8173-nor", @@ -10,6 +10,7 @@ Required properties: "mediatek,mt2712-nor", "mediatek,mt8173-nor" "mediatek,mt7622-nor", "mediatek,mt8173-nor" "mediatek,mt7623-nor", "mediatek,mt8173-nor" + "mediatek,mt7629-nor", "mediatek,mt8173-nor" "mediatek,mt8173-nor" - reg: physical base address and length of the controller's register - clocks: the phandle of the clocks needed by the nor controller diff --git a/dts/Bindings/mtd/stm32-fmc2-nand.txt b/dts/Bindings/mtd/stm32-fmc2-nand.txt new file mode 100644 index 0000000000..ad2bef8265 --- /dev/null +++ b/dts/Bindings/mtd/stm32-fmc2-nand.txt @@ -0,0 +1,61 @@ +STMicroelectronics Flexible Memory Controller 2 (FMC2) +NAND Interface + +Required properties: +- compatible: Should be one of: + * st,stm32mp15-fmc2 +- reg: NAND flash controller memory areas. + First region contains the register location. + Regions 2 to 4 respectively contain the data, command, + and address space for CS0. + Regions 5 to 7 contain the same areas for CS1. +- interrupts: The interrupt number +- pinctrl-0: Standard Pinctrl phandle (see: pinctrl/pinctrl-bindings.txt) +- clocks: The clock needed by the NAND flash controller + +Optional properties: +- resets: Reference to a reset controller asserting the FMC controller +- dmas: DMA specifiers (see: dma/stm32-mdma.txt) +- dma-names: Must be "tx", "rx" and "ecc" + +* NAND device bindings: + +Required properties: +- reg: describes the CS lines assigned to the NAND device. + +Optional properties: +- nand-on-flash-bbt: see nand.txt +- nand-ecc-strength: see nand.txt +- nand-ecc-step-size: see nand.txt + +The following ECC strength and step size are currently supported: + - nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Hamming) + - nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4) + - nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8) (default) + +Example: + + fmc: nand-controller@58002000 { + compatible = "st,stm32mp15-fmc2"; + reg = <0x58002000 0x1000>, + <0x80000000 0x1000>, + <0x88010000 0x1000>, + <0x88020000 0x1000>, + <0x81000000 0x1000>, + <0x89010000 0x1000>, + <0x89020000 0x1000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc FMC_K>; + resets = <&rcc FMC_R>; + pinctrl-names = "default"; + pinctrl-0 = <&fmc_pins_a>; + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + nand-on-flash-bbt; + #address-cells = <1>; + #size-cells = <1>; + }; + }; |