summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/net/dsa/realtek-smi.txt
diff options
context:
space:
mode:
Diffstat (limited to 'dts/Bindings/net/dsa/realtek-smi.txt')
-rw-r--r--dts/Bindings/net/dsa/realtek-smi.txt153
1 files changed, 153 insertions, 0 deletions
diff --git a/dts/Bindings/net/dsa/realtek-smi.txt b/dts/Bindings/net/dsa/realtek-smi.txt
new file mode 100644
index 0000000..b6ae854
--- /dev/null
+++ b/dts/Bindings/net/dsa/realtek-smi.txt
@@ -0,0 +1,153 @@
+Realtek SMI-based Switches
+==========================
+
+The SMI "Simple Management Interface" is a two-wire protocol using
+bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does
+not use the MDIO protocol. This binding defines how to specify the
+SMI-based Realtek devices.
+
+Required properties:
+
+- compatible: must be exactly one of:
+ "realtek,rtl8366"
+ "realtek,rtl8366rb" (4+1 ports)
+ "realtek,rtl8366s" (4+1 ports)
+ "realtek,rtl8367"
+ "realtek,rtl8367b"
+ "realtek,rtl8368s" (8 port)
+ "realtek,rtl8369"
+ "realtek,rtl8370" (8 port)
+
+Required properties:
+- mdc-gpios: GPIO line for the MDC clock line.
+- mdio-gpios: GPIO line for the MDIO data line.
+- reset-gpios: GPIO line for the reset signal.
+
+Optional properties:
+- realtek,disable-leds: if the LED drivers are not used in the
+ hardware design this will disable them so they are not turned on
+ and wasting power.
+
+Required subnodes:
+
+- interrupt-controller
+
+ This defines an interrupt controller with an IRQ line (typically
+ a GPIO) that will demultiplex and handle the interrupt from the single
+ interrupt line coming out of one of the SMI-based chips. It most
+ importantly provides link up/down interrupts to the PHY blocks inside
+ the ASIC.
+
+Required properties of interrupt-controller:
+
+- interrupt: parent interrupt, see interrupt-controller/interrupts.txt
+- interrupt-controller: see interrupt-controller/interrupts.txt
+- #address-cells: should be <0>
+- #interrupt-cells: should be <1>
+
+- mdio
+
+ This defines the internal MDIO bus of the SMI device, mostly for the
+ purpose of being able to hook the interrupts to the right PHY and
+ the right PHY to the corresponding port.
+
+Required properties of mdio:
+
+- compatible: should be set to "realtek,smi-mdio" for all SMI devices
+
+See net/mdio.txt for additional MDIO bus properties.
+
+See net/dsa/dsa.txt for a list of additional required and optional properties
+and subnodes of DSA switches.
+
+Examples:
+
+switch {
+ compatible = "realtek,rtl8366rb";
+ /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
+ mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+ mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+
+ switch_intc: interrupt-controller {
+ /* GPIO 15 provides the interrupt */
+ interrupt-parent = <&gpio0>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ port@0 {
+ reg = <0>;
+ label = "lan0";
+ phy-handle = <&phy0>;
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-handle = <&phy1>;
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-handle = <&phy2>;
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ phy-handle = <&phy3>;
+ };
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ phy-handle = <&phy4>;
+ };
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+
+ mdio {
+ compatible = "realtek,smi-mdio", "dsa-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: phy@0 {
+ reg = <0>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <0>;
+ };
+ phy1: phy@1 {
+ reg = <1>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <1>;
+ };
+ phy2: phy@2 {
+ reg = <2>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <2>;
+ };
+ phy3: phy@3 {
+ reg = <3>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <3>;
+ };
+ phy4: phy@4 {
+ reg = <4>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <12>;
+ };
+ };
+};