diff options
Diffstat (limited to 'dts/Bindings/net/dsa/sja1105.txt')
| -rw-r--r-- | dts/Bindings/net/dsa/sja1105.txt | 156 |
1 files changed, 0 insertions, 156 deletions
diff --git a/dts/Bindings/net/dsa/sja1105.txt b/dts/Bindings/net/dsa/sja1105.txt deleted file mode 100644 index 13fd21074d..0000000000 --- a/dts/Bindings/net/dsa/sja1105.txt +++ /dev/null @@ -1,156 +0,0 @@ -NXP SJA1105 switch driver -========================= - -Required properties: - -- compatible: - Must be one of: - - "nxp,sja1105e" - - "nxp,sja1105t" - - "nxp,sja1105p" - - "nxp,sja1105q" - - "nxp,sja1105r" - - "nxp,sja1105s" - - Although the device ID could be detected at runtime, explicit bindings - are required in order to be able to statically check their validity. - For example, SGMII can only be specified on port 4 of R and S devices, - and the non-SGMII devices, while pin-compatible, are not equal in terms - of support for RGMII internal delays (supported on P/Q/R/S, but not on - E/T). - -Optional properties: - -- sja1105,role-mac: -- sja1105,role-phy: - Boolean properties that can be assigned under each port node. By - default (unless otherwise specified) a port is configured as MAC if it - is driving a PHY (phy-handle is present) or as PHY if it is PHY-less - (fixed-link specified, presumably because it is connected to a MAC). - The effect of this property (in either its implicit or explicit form) - is: - - In the case of MII or RMII it specifies whether the SJA1105 port is a - clock source or sink for this interface (not applicable for RGMII - where there is a Tx and an Rx clock). - - In the case of RGMII it affects the behavior regarding internal - delays: - 1. If sja1105,role-mac is specified, and the phy-mode property is one - of "rgmii-id", "rgmii-txid" or "rgmii-rxid", then the entity - designated to apply the delay/clock skew necessary for RGMII - is the PHY. The SJA1105 MAC does not apply any internal delays. - 2. If sja1105,role-phy is specified, and the phy-mode property is one - of the above, the designated entity to apply the internal delays - is the SJA1105 MAC (if hardware-supported). This is only supported - by the second-generation (P/Q/R/S) hardware. On a first-generation - E or T device, it is an error to specify an RGMII phy-mode other - than "rgmii" for a port that is in fixed-link mode. In that case, - the clock skew must either be added by the MAC at the other end of - the fixed-link, or by PCB serpentine traces on the board. - These properties are required, for example, in the case where SJA1105 - ports are at both ends of a MII/RMII PHY-less setup. One end would need - to have sja1105,role-mac, while the other sja1105,role-phy. - -See Documentation/devicetree/bindings/net/dsa/dsa.txt for the list of standard -DSA required and optional properties. - -Other observations ------------------- - -The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944) of at least -one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum -cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed -depends on the SPI bus master driver. - -Example -------- - -Ethernet switch connected via SPI to the host, CPU port wired to enet2: - -arch/arm/boot/dts/ls1021a-tsn.dts: - -/* SPI controller of the LS1021 */ -&dspi0 { - sja1105@1 { - reg = <0x1>; - #address-cells = <1>; - #size-cells = <0>; - compatible = "nxp,sja1105t"; - spi-max-frequency = <4000000>; - fsl,spi-cs-sck-delay = <1000>; - fsl,spi-sck-cs-delay = <1000>; - ports { - #address-cells = <1>; - #size-cells = <0>; - port@0 { - /* ETH5 written on chassis */ - label = "swp5"; - phy-handle = <&rgmii_phy6>; - phy-mode = "rgmii-id"; - reg = <0>; - /* Implicit "sja1105,role-mac;" */ - }; - port@1 { - /* ETH2 written on chassis */ - label = "swp2"; - phy-handle = <&rgmii_phy3>; - phy-mode = "rgmii-id"; - reg = <1>; - /* Implicit "sja1105,role-mac;" */ - }; - port@2 { - /* ETH3 written on chassis */ - label = "swp3"; - phy-handle = <&rgmii_phy4>; - phy-mode = "rgmii-id"; - reg = <2>; - /* Implicit "sja1105,role-mac;" */ - }; - port@3 { - /* ETH4 written on chassis */ - phy-handle = <&rgmii_phy5>; - label = "swp4"; - phy-mode = "rgmii-id"; - reg = <3>; - /* Implicit "sja1105,role-mac;" */ - }; - port@4 { - /* Internal port connected to eth2 */ - ethernet = <&enet2>; - phy-mode = "rgmii"; - reg = <4>; - /* Implicit "sja1105,role-phy;" */ - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; -}; - -/* MDIO controller of the LS1021 */ -&mdio0 { - /* BCM5464 */ - rgmii_phy3: ethernet-phy@3 { - reg = <0x3>; - }; - rgmii_phy4: ethernet-phy@4 { - reg = <0x4>; - }; - rgmii_phy5: ethernet-phy@5 { - reg = <0x5>; - }; - rgmii_phy6: ethernet-phy@6 { - reg = <0x6>; - }; -}; - -/* Ethernet master port of the LS1021 */ -&enet2 { - phy-connection-type = "rgmii"; - status = "ok"; - fixed-link { - speed = <1000>; - full-duplex; - }; -}; |