diff options
Diffstat (limited to 'dts/Bindings/net/macb.txt')
-rw-r--r-- | dts/Bindings/net/macb.txt | 60 |
1 files changed, 0 insertions, 60 deletions
diff --git a/dts/Bindings/net/macb.txt b/dts/Bindings/net/macb.txt deleted file mode 100644 index a1b06fd196..0000000000 --- a/dts/Bindings/net/macb.txt +++ /dev/null @@ -1,60 +0,0 @@ -* Cadence MACB/GEM Ethernet controller - -Required properties: -- compatible: Should be "cdns,[<chip>-]{macb|gem}" - Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC. - Use "cdns,at91sam9260-macb" for Atmel at91sam9 SoCs. - Use "cdns,sam9x60-macb" for Microchip sam9x60 SoC. - Use "cdns,np4-macb" for NP4 SoC devices. - Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb". - Use "atmel,sama5d2-gem" for the GEM IP (10/100) available on Atmel sama5d2 SoCs. - Use "atmel,sama5d29-gem" for GEM XL IP (10/100) available on Atmel sama5d29 SoCs. - Use "atmel,sama5d3-macb" for the 10/100Mbit IP available on Atmel sama5d3 SoCs. - Use "atmel,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs. - Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs. - Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC. - Use "cdns,zynqmp-gem" for Zynq Ultrascale+ MPSoC. - Use "sifive,fu540-c000-gem" for SiFive FU540-C000 SoC. - Use "microchip,sama7g5-emac" for Microchip SAMA7G5 ethernet interface. - Use "microchip,sama7g5-gem" for Microchip SAMA7G5 gigabit ethernet interface. - Or the generic form: "cdns,emac". -- reg: Address and length of the register set for the device - For "sifive,fu540-c000-gem", second range is required to specify the - address and length of the registers for GEMGXL Management block. -- interrupts: Should contain macb interrupt -- phy-mode: See ethernet.txt file in the same directory. -- clock-names: Tuple listing input clock names. - Required elements: 'pclk', 'hclk' - Optional elements: 'tx_clk' - Optional elements: 'rx_clk' applies to cdns,zynqmp-gem - Optional elements: 'tsu_clk' -- clocks: Phandles to input clocks. - -Optional properties: -- mdio: node containing PHY children. If this node is not present, then PHYs - will be direct children. - -The MAC address will be determined using the optional properties -defined in ethernet.txt. - -Optional properties for PHY child node: -- reset-gpios : Should specify the gpio for phy reset -- magic-packet : If present, indicates that the hardware supports waking - up via magic packet. -- phy-handle : see ethernet.txt file in the same directory - -Examples: - - macb0: ethernet@fffc4000 { - compatible = "cdns,at32ap7000-macb"; - reg = <0xfffc4000 0x4000>; - interrupts = <21>; - phy-mode = "rmii"; - local-mac-address = [3a 0e 03 04 05 06]; - clock-names = "pclk", "hclk", "tx_clk"; - clocks = <&clkc 30>, <&clkc 30>, <&clkc 13>; - ethernet-phy@1 { - reg = <0x1>; - reset-gpios = <&pioE 6 1>; - }; - }; |