1 files changed, 0 insertions, 93 deletions
diff --git a/dts/Bindings/net/xilinx_axienet.txt b/dts/Bindings/net/xilinx_axienet.txt
deleted file mode 100644
index b8e4894bc6..0000000000
--- a/dts/Bindings/net/xilinx_axienet.txt
+++ /dev/null
@@ -1,93 +0,0 @@
-XILINX AXI ETHERNET Device Tree Bindings
---------------------------------------------------------
-
-Also called  AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core
-provides connectivity to an external ethernet PHY supporting different
-interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two
-segments of memory for buffering TX and RX, as well as the capability of
-offloading TX/RX checksum calculation off the processor.
-
-Management configuration is done through the AXI interface, while payload is
-sent and received through means of an AXI DMA controller. This driver
-includes the DMA driver code, so this driver is incompatible with AXI DMA
-driver.
-
-For more details about mdio please refer phy.txt file in the same directory.
-
-Required properties:
-- compatible	: Must be one of "xlnx,axi-ethernet-1.00.a",
-		  "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a"
-- reg		: Address and length of the IO space, as well as the address
-                  and length of the AXI DMA controller IO space, unless
-                  axistream-connected is specified, in which case the reg
-                  attribute of the node referenced by it is used.
-- interrupts	: Should be a list of 2 or 3 interrupts: TX DMA, RX DMA,
-		  and optionally Ethernet core. If axistream-connected is
-		  specified, the TX/RX DMA interrupts should be on that node
-		  instead, and only the Ethernet core interrupt is optionally
-		  specified here.
-- phy-handle	: Should point to the external phy device.
-		  See ethernet.txt file in the same directory.
-- xlnx,rxmem	: Set to allocated memory buffer for Rx/Tx in the hardware
-
-Optional properties:
-- phy-mode	: See ethernet.txt
-- xlnx,phy-type	: Deprecated, do not use, but still accepted in preference
-		  to phy-mode.
-- xlnx,txcsum	: 0 or empty for disabling TX checksum offload,
-		  1 to enable partial TX checksum offload,
-		  2 to enable full TX checksum offload
-- xlnx,rxcsum	: Same values as xlnx,txcsum but for RX checksum offload
-- xlnx,switch-x-sgmii : Boolean to indicate the Ethernet core is configured to
-		  support both 1000BaseX and SGMII modes. If set, the phy-mode
-		  should be set to match the mode selected on core reset (i.e.
-		  by the basex_or_sgmii core input line).
-- clock-names: 	  Tuple listing input clock names. Possible clocks:
-		  s_axi_lite_clk: Clock for AXI register slave interface
-		  axis_clk: AXI4-Stream clock for TXD RXD TXC and RXS interfaces
-		  ref_clk: Ethernet reference clock, used by signal delay
-			   primitives and transceivers
-		  mgt_clk: MGT reference clock (used by optional internal
-			   PCS/PMA PHY)
-
-		  Note that if s_axi_lite_clk is not specified by name, the
-		  first clock of any name is used for this. If that is also not
-		  specified, the clock rate is auto-detected from the CPU clock
-		  (but only on platforms where this is possible). New device
-		  trees should specify all applicable clocks by name - the
-		  fallbacks to an unnamed clock or to CPU clock are only for
-		  backward compatibility.
-- clocks: 	  Phandles to input clocks matching clock-names. Refer to common
-		  clock bindings.
-- axistream-connected: Reference to another node which contains the resources
-		       for the AXI DMA controller used by this device.
-		       If this is specified, the DMA-related resources from that
-		       device (DMA registers and DMA TX/RX interrupts) rather
-		       than this one will be used.
- - mdio		: Child node for MDIO bus. Must be defined if PHY access is
-		  required through the core's MDIO interface (i.e. always,
-		  unless the PHY is accessed through a different bus).
-
-Example:
-	axi_ethernet_eth: ethernet@40c00000 {
-		compatible = "xlnx,axi-ethernet-1.00.a";
-		device_type = "network";
-		interrupt-parent = <&microblaze_0_axi_intc>;
-		interrupts = <2 0 1>;
-		clock-names = "s_axi_lite_clk", "axis_clk", "ref_clk", "mgt_clk";
-		clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>;
-		phy-mode = "mii";
-		reg = <0x40c00000 0x40000 0x50c00000 0x40000>;
-		xlnx,rxcsum = <0x2>;
-		xlnx,rxmem = <0x800>;
-		xlnx,txcsum = <0x2>;
-		phy-handle = <&phy0>;
-		axi_ethernetlite_0_mdio: mdio {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			phy0: phy@0 {
-				device_type = "ethernet-phy";
-				reg = <1>;
-			};
-		};
-	};