diff options
Diffstat (limited to 'dts/Bindings/phy/phy-stm32-usbphyc.yaml')
| -rw-r--r-- | dts/Bindings/phy/phy-stm32-usbphyc.yaml | 282 |
1 files changed, 282 insertions, 0 deletions
diff --git a/dts/Bindings/phy/phy-stm32-usbphyc.yaml b/dts/Bindings/phy/phy-stm32-usbphyc.yaml new file mode 100644 index 0000000000..24a3dbde22 --- /dev/null +++ b/dts/Bindings/phy/phy-stm32-usbphyc.yaml @@ -0,0 +1,282 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/phy-stm32-usbphyc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32 USB HS PHY controller + +description: + + The STM32 USBPHYC block contains a dual port High Speed UTMI+ PHY and a UTMI + switch. It controls PHY configuration and status, and the UTMI+ switch that + selects either OTG or HOST controller for the second PHY port. It also sets + PLL configuration. + + USBPHYC + |_ PLL + | + |_ PHY port#1 _________________ HOST controller + | __ | + | / 1|________________| + |_ PHY port#2 ----| |________________ + | \_0| | + |_ UTMI switch_______| OTG controller + +maintainers: + - Amelie Delaunay <amelie.delaunay@foss.st.com> + +properties: + compatible: + const: st,stm32mp1-usbphyc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + vdda1v1-supply: + description: regulator providing 1V1 power supply to the PLL block + + vdda1v8-supply: + description: regulator providing 1V8 power supply to the PLL block + + '#clock-cells': + description: number of clock cells for ck_usbo_48m consumer + const: 0 + +# Required child nodes: + +patternProperties: + "^usb-phy@[0|1]$": + type: object + description: + Each port the controller provides must be represented as a sub-node. + + properties: + reg: + description: phy port index. + maxItems: 1 + + phy-supply: + description: regulator providing 3V3 power supply to the PHY. + + "#phy-cells": + enum: [ 0x0, 0x1 ] + + connector: + type: object + $ref: /schemas/connector/usb-connector.yaml + unevaluatedProperties: false + + properties: + vbus-supply: true + + # It can be necessary to adjust the PHY settings to compensate parasitics, which can be due + # to USB connector/receptacle, routing, ESD protection component,... Here is the list of + # all optional parameters to tune the interface of the PHY (HS for High-Speed, FS for Full- + # Speed, LS for Low-Speed) + + st,current-boost-microamp: + description: Current boosting in uA + enum: [ 1000, 2000 ] + + st,no-lsfs-fb-cap: + description: Disables the LS/FS feedback capacitor + type: boolean + + st,decrease-hs-slew-rate: + description: Decreases the HS driver slew rate by 10% + type: boolean + + st,tune-hs-dc-level: + description: | + Tunes the HS driver DC level + - <0> normal level + - <1> increases the level by 5 to 7 mV + - <2> increases the level by 10 to 14 mV + - <3> decreases the level by 5 to 7 mV + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + default: 0 + + st,enable-fs-rftime-tuning: + description: Enables the FS rise/fall tuning option + type: boolean + + st,enable-hs-rftime-reduction: + description: Enables the HS rise/fall reduction feature + type: boolean + + st,trim-hs-current: + description: | + Controls HS driver current trimming for choke compensation + - <0> = 18.87 mA target current / nominal + 0% + - <1> = 19.165 mA target current / nominal + 1.56% + - <2> = 19.46 mA target current / nominal + 3.12% + - <3> = 19.755 mA target current / nominal + 4.68% + - <4> = 20.05 mA target current / nominal + 6.24% + - <5> = 20.345 mA target current / nominal + 7.8% + - <6> = 20.64 mA target current / nominal + 9.36% + - <7> = 20.935 mA target current / nominal + 10.92% + - <8> = 21.23 mA target current / nominal + 12.48% + - <9> = 21.525 mA target current / nominal + 14.04% + - <10> = 21.82 mA target current / nominal + 15.6% + - <11> = 22.115 mA target current / nominal + 17.16% + - <12> = 22.458 mA target current / nominal + 19.01% + - <13> = 22.755 mA target current / nominal + 20.58% + - <14> = 23.052 mA target current / nominal + 22.16% + - <15> = 23.348 mA target current / nominal + 23.73% + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + default: 0 + + st,trim-hs-impedance: + description: | + Controls HS driver impedance tuning for choke compensation + - <0> = no impedance offset + - <1> = reduce the impedance by 2 ohms + - <2> = reduce the impedance by 4 ohms + - <3> = reduce the impedance by 6 ohms + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + default: 0 + + st,tune-squelch-level: + description: | + Tunes the squelch DC threshold value + - <0> = no shift in threshold + - <1> = threshold shift by +7 mV + - <2> = threshold shift by -5 mV + - <3> = threshold shift by +14 mV + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + default: 0 + + st,enable-hs-rx-gain-eq: + description: Enables the HS Rx gain equalizer + type: boolean + + st,tune-hs-rx-offset: + description: | + Adjusts the HS Rx offset + - <0> = no offset + - <1> = offset of +5 mV + - <2> = offset of +10 mV + - <3> = offset of -5 mV + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + default: 0 + + st,no-hs-ftime-ctrl: + description: Disables the HS fall time control of single ended signals during pre-emphasis + type: boolean + + st,no-lsfs-sc: + description: Disables the short circuit protection in LS/FS driver + type: boolean + + st,enable-hs-tx-staggering: + description: Enables the basic staggering in HS Tx mode + type: boolean + + allOf: + - if: + properties: + reg: + const: 0 + then: + properties: + "#phy-cells": + const: 0 + else: + properties: + "#phy-cells": + const: 1 + description: + The value is used to select UTMI switch output. + 0 for OTG controller and 1 for Host controller. + + required: + - reg + - phy-supply + - "#phy-cells" + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - "#address-cells" + - "#size-cells" + - vdda1v1-supply + - vdda1v8-supply + - usb-phy@0 + - usb-phy@1 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/stm32mp1-clks.h> + #include <dt-bindings/reset/stm32mp1-resets.h> + usbphyc: usbphyc@5a006000 { + compatible = "st,stm32mp1-usbphyc"; + reg = <0x5a006000 0x1000>; + clocks = <&rcc USBPHY_K>; + resets = <&rcc USBPHY_R>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <0>; + + usbphyc_port0: usb-phy@0 { + reg = <0>; + phy-supply = <&vdd_usb>; + #phy-cells = <0>; + st,tune-hs-dc-level = <2>; + st,enable-fs-rftime-tuning; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <15>; + st,trim-hs-impedance = <1>; + st,tune-squelch-level = <3>; + st,tune-hs-rx-offset = <2>; + st,no-lsfs-sc; + connector { + compatible = "usb-a-connector"; + vbus-supply = <&vbus_sw>; + }; + }; + + usbphyc_port1: usb-phy@1 { + reg = <1>; + phy-supply = <&vdd_usb>; + #phy-cells = <1>; + st,tune-hs-dc-level = <2>; + st,enable-fs-rftime-tuning; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <15>; + st,trim-hs-impedance = <1>; + st,tune-squelch-level = <3>; + st,tune-hs-rx-offset = <2>; + st,no-lsfs-sc; + }; + }; +... |