diff options
Diffstat (limited to 'dts/Bindings/power')
| -rw-r--r-- | dts/Bindings/power/qcom,coincell-charger.txt | 2 | ||||
| -rw-r--r-- | dts/Bindings/power/renesas,rcar-sysc.txt | 48 | ||||
| -rw-r--r-- | dts/Bindings/power/reset/gpio-poweroff.txt | 36 | ||||
| -rw-r--r-- | dts/Bindings/power/reset/gpio-restart.txt | 54 | ||||
| -rw-r--r-- | dts/Bindings/power/rockchip-io-domain.txt | 4 |
5 files changed, 142 insertions, 2 deletions
diff --git a/dts/Bindings/power/qcom,coincell-charger.txt b/dts/Bindings/power/qcom,coincell-charger.txt index 0e6d8754e7..7478992232 100644 --- a/dts/Bindings/power/qcom,coincell-charger.txt +++ b/dts/Bindings/power/qcom,coincell-charger.txt @@ -29,7 +29,7 @@ IC (PMIC) - qcom,charger-disable: Usage: optional Value type: <boolean> - Definition: definining this property disables charging + Definition: defining this property disables charging This charger is a sub-node of one of the 8941 PMIC blocks, and is specified as a child node in DTS of that node. See ../mfd/qcom,spmi-pmic.txt and diff --git a/dts/Bindings/power/renesas,rcar-sysc.txt b/dts/Bindings/power/renesas,rcar-sysc.txt new file mode 100644 index 0000000000..b74e4d4785 --- /dev/null +++ b/dts/Bindings/power/renesas,rcar-sysc.txt @@ -0,0 +1,48 @@ +DT bindings for the Renesas R-Car System Controller + +== System Controller Node == + +The R-Car System Controller provides power management for the CPU cores and +various coprocessors. + +Required properties: + - compatible: Must contain exactly one of the following: + - "renesas,r8a7779-sysc" (R-Car H1) + - "renesas,r8a7790-sysc" (R-Car H2) + - "renesas,r8a7791-sysc" (R-Car M2-W) + - "renesas,r8a7792-sysc" (R-Car V2H) + - "renesas,r8a7793-sysc" (R-Car M2-N) + - "renesas,r8a7794-sysc" (R-Car E2) + - "renesas,r8a7795-sysc" (R-Car H3) + - reg: Address start and address range for the device. + - #power-domain-cells: Must be 1. + + +Example: + + sysc: system-controller@e6180000 { + compatible = "renesas,r8a7791-sysc"; + reg = <0 0xe6180000 0 0x0200>; + #power-domain-cells = <1>; + }; + + +== PM Domain Consumers == + +Devices residing in a power area must refer to that power area, as documented +by the generic PM domain bindings in +Documentation/devicetree/bindings/power/power_domain.txt. + +Required properties: + - power-domains: A phandle and symbolic PM domain specifier, as defined in + <dt-bindings/power/r8a77*-sysc.h>. + + +Example: + + L2_CA15: cache-controller@0 { + compatible = "cache"; + power-domains = <&sysc R8A7791_PD_CA15_SCU>; + cache-unified; + cache-level = <2>; + }; diff --git a/dts/Bindings/power/reset/gpio-poweroff.txt b/dts/Bindings/power/reset/gpio-poweroff.txt new file mode 100644 index 0000000000..d4eab9227e --- /dev/null +++ b/dts/Bindings/power/reset/gpio-poweroff.txt @@ -0,0 +1,36 @@ +Driver a GPIO line that can be used to turn the power off. + +The driver supports both level triggered and edge triggered power off. +At driver load time, the driver will request the given gpio line and +install a pm_power_off handler. If the optional properties 'input' is +not found, the GPIO line will be driven in the inactive +state. Otherwise its configured as an input. + +When the pm_power_off is called, the gpio is configured as an output, +and drive active, so triggering a level triggered power off +condition. This will also cause an inactive->active edge condition, so +triggering positive edge triggered power off. After a delay of 100ms, +the GPIO is set to inactive, thus causing an active->inactive edge, +triggering negative edge triggered power off. After another 100ms +delay the GPIO is driver active again. If the power is still on and +the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted. + +Required properties: +- compatible : should be "gpio-poweroff". +- gpios : The GPIO to set high/low, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be + low to power down the board set it to "Active Low", otherwise set + gpio to "Active High". + +Optional properties: +- input : Initially configure the GPIO line as an input. Only reconfigure + it to an output when the pm_power_off function is called. If this optional + property is not specified, the GPIO is initialized as an output in its + inactive state. + +Examples: + +gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio 4 0>; +}; diff --git a/dts/Bindings/power/reset/gpio-restart.txt b/dts/Bindings/power/reset/gpio-restart.txt new file mode 100644 index 0000000000..af3701bc15 --- /dev/null +++ b/dts/Bindings/power/reset/gpio-restart.txt @@ -0,0 +1,54 @@ +Drive a GPIO line that can be used to restart the system from a restart +handler. + +This binding supports level and edge triggered reset. At driver load +time, the driver will request the given gpio line and install a restart +handler. If the optional properties 'open-source' is not found, the GPIO line +will be driven in the inactive state. Otherwise its not driven until +the restart is initiated. + +When the system is restarted, the restart handler will be invoked in +priority order. The gpio is configured as an output, and driven active, +triggering a level triggered reset condition. This will also cause an +inactive->active edge condition, triggering positive edge triggered +reset. After a delay specified by active-delay, the GPIO is set to +inactive, thus causing an active->inactive edge, triggering negative edge +triggered reset. After a delay specified by inactive-delay, the GPIO +is driven active again. After a delay specified by wait-delay, the +restart handler completes allowing other restart handlers to be attempted. + +Required properties: +- compatible : should be "gpio-restart". +- gpios : The GPIO to set high/low, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be + low to reset the board set it to "Active Low", otherwise set + gpio to "Active High". + +Optional properties: +- open-source : Treat the GPIO as being open source and defer driving + it to when the restart is initiated. If this optional property is not + specified, the GPIO is initialized as an output in its inactive state. +- priority : A priority ranging from 0 to 255 (default 128) according to + the following guidelines: + 0: Restart handler of last resort, with limited restart + capabilities + 128: Default restart handler; use if no other restart handler is + expected to be available, and/or if restart functionality is + sufficient to restart the entire system + 255: Highest priority restart handler, will preempt all other + restart handlers +- active-delay: Delay (default 100) to wait after driving gpio active [ms] +- inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms] +- wait-delay: Delay (default 3000) to wait after completing restart + sequence [ms] + +Examples: + +gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio 4 0>; + priority = <128>; + active-delay = <100>; + inactive-delay = <100>; + wait-delay = <3000>; +}; diff --git a/dts/Bindings/power/rockchip-io-domain.txt b/dts/Bindings/power/rockchip-io-domain.txt index c84fb47265..d23dc002a8 100644 --- a/dts/Bindings/power/rockchip-io-domain.txt +++ b/dts/Bindings/power/rockchip-io-domain.txt @@ -37,8 +37,10 @@ Required properties: - "rockchip,rk3368-pmu-io-voltage-domain" for rk3368 pmu-domains - "rockchip,rk3399-io-voltage-domain" for rk3399 - "rockchip,rk3399-pmu-io-voltage-domain" for rk3399 pmu-domains -- rockchip,grf: phandle to the syscon managing the "general register files" +Deprecated properties: +- rockchip,grf: phandle to the syscon managing the "general register files" + Systems should move the io-domains to a sub-node of the grf simple-mfd. You specify supplies using the standard regulator bindings by including a phandle the relevant regulator. All specified supplies must be able |