diff options
Diffstat (limited to 'dts/src/arm/intel-ixp42x-dlink-dsm-g600.dts')
| -rw-r--r-- | dts/src/arm/intel-ixp42x-dlink-dsm-g600.dts | 145 |
1 files changed, 0 insertions, 145 deletions
diff --git a/dts/src/arm/intel-ixp42x-dlink-dsm-g600.dts b/dts/src/arm/intel-ixp42x-dlink-dsm-g600.dts deleted file mode 100644 index 8b32e9f22d..0000000000 --- a/dts/src/arm/intel-ixp42x-dlink-dsm-g600.dts +++ /dev/null @@ -1,145 +0,0 @@ -// SPDX-License-Identifier: ISC -/* - * Device Tree file for D-Link DSM-G600 revision A based on IXP420 - * NOTE: revision B of this device uses PowerPC and is NOT supported by - * this device tree. - * - * Inspired by the boardfile by Rod Whitby, Tower Technologies, Alessandro Zummo - * and Michael Westerhof. - */ - -/dts-v1/; - -#include "intel-ixp42x.dtsi" -#include <dt-bindings/input/input.h> - -/ { - model = "D-Link DSM-G600 rev A"; - compatible = "dlink,dsm-g600-a", "intel,ixp42x"; - #address-cells = <1>; - #size-cells = <1>; - - memory@0 { - /* 64 MB SDRAM */ - device_type = "memory"; - reg = <0x00000000 0x4000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait"; - stdout-path = "uart0:115200n8"; - }; - - aliases { - serial0 = &uart0; - }; - - leds { - compatible = "gpio-leds"; - led-power { - label = "dsmg600:green:power"; - gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; - default-state = "on"; - linux,default-trigger = "heartbeat"; - }; - led-wlan { - label = "dsmg600:green:wlan"; - /* CHECKME: flagged as active low in the old board file */ - gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; - default-state = "on"; - /* We don't have WLAN trigger in the kernel (yet) */ - linux,default-trigger = "netdev"; - }; - }; - - gpio_keys { - compatible = "gpio-keys"; - - button-reset { - wakeup-source; - linux,code = <KEY_ESC>; - label = "reset"; - gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; - }; - }; - - gpio_keys_polled { - compatible = "gpio-keys-polled"; - - /* - * According to the board file this key cannot handle interrupts and - * need to be polled. Investigate if this is really the case or if - * this can be moved adjacent to the ordinary gpio-keys above. - */ - button-power { - wakeup-source; - linux,code = <KEY_POWER>; - label = "power"; - gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; - }; - }; - - i2c { - compatible = "i2c-gpio"; - sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; - scl-gpios = <&gpio0 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; - #address-cells = <1>; - #size-cells = <0>; - - rtc@51 { - compatible = "nxp,pcf8563"; - reg = <0x51>; - }; - }; - - gpio-poweroff { - compatible = "gpio-poweroff"; - gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; - timeout-ms = <5000>; - }; - - soc { - bus@c4000000 { - /* The first 16MB region at CS0 on the expansion bus */ - flash@0,0 { - compatible = "intel,ixp4xx-flash", "cfi-flash"; - bank-width = <2>; - /* - * 16 MB of Flash in 128 0x20000 sized blocks - * mapped in at CS0. - */ - reg = <0 0x00000000 0x1000000>; - - partitions { - compatible = "redboot-fis"; - /* - * A boot log says the directory is at 0xfe0000 - * 0x7f * 0x20000 = 0xfe0000 - */ - fis-index-block = <0x7f>; - }; - }; - }; - - pci@c0000000 { - status = "ok"; - - /* - * Taken from DSM-G600 PCI boardfile (dsmg600-pci.c) - * We have slots (IDSEL) 1, 2, 3, 4 and pins 1, 2 and 3. - * Only slot 3 have three IRQs. - */ - interrupt-map = - /* IDSEL 1 */ - <0x0800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT E on slot 1 is irq 7 */ - /* IDSEL 2 */ - <0x1000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 11 */ - /* IDSEL 3 */ - <0x1800 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 10 */ - <0x1800 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 9 */ - <0x1800 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 8 */ - /* IDSEL 4 */ - <0x2000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT F on slot 4 is irq 6 */ - }; - }; -}; |