diff options
Diffstat (limited to 'dts/src/arm64/qcom/sc7280-idp.dtsi')
| -rw-r--r-- | dts/src/arm64/qcom/sc7280-idp.dtsi | 271 |
1 files changed, 265 insertions, 6 deletions
diff --git a/dts/src/arm64/qcom/sc7280-idp.dtsi b/dts/src/arm64/qcom/sc7280-idp.dtsi index 371a2a9dcf..d623d71d8b 100644 --- a/dts/src/arm64/qcom/sc7280-idp.dtsi +++ b/dts/src/arm64/qcom/sc7280-idp.dtsi @@ -7,11 +7,96 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> +#include <dt-bindings/input/linux-event-codes.h> #include "sc7280.dtsi" #include "pm7325.dtsi" #include "pm8350c.dtsi" #include "pmk8350.dtsi" +/ { + gpio-keys { + compatible = "gpio-keys"; + label = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&key_vol_up_default>; + + volume-up { + label = "volume_up"; + gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = <KEY_VOLUMEUP>; + gpio-key,wakeup; + debounce-interval = <15>; + linux,can-disable; + }; + }; + + nvme_3v3_regulator: nvme-3v3-regulator { + compatible = "regulator-fixed"; + regulator-name = "VLDO_3V3"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&nvme_pwren>; + }; +}; + +/* + * Reserved memory changes + * + * Delete all unused memory nodes and define the peripheral memory regions + * required by the board dts. + * + */ + +/delete-node/ &hyp_mem; +/delete-node/ &xbl_mem; +/delete-node/ &reserved_xbl_uefi_log; +/delete-node/ &sec_apps_mem; + +/* Increase the size from 2.5MB to 8MB */ +&rmtfs_mem { + reg = <0x0 0x9c900000 0x0 0x800000>; +}; + +/ { + reserved-memory { + adsp_mem: memory@86700000 { + reg = <0x0 0x86700000 0x0 0x2800000>; + no-map; + }; + + camera_mem: memory@8ad00000 { + reg = <0x0 0x8ad00000 0x0 0x500000>; + no-map; + }; + + venus_mem: memory@8b200000 { + reg = <0x0 0x8b200000 0x0 0x500000>; + no-map; + }; + + mpss_mem: memory@8b800000 { + reg = <0x0 0x8b800000 0x0 0xf600000>; + no-map; + }; + + wpss_mem: memory@9ae00000 { + reg = <0x0 0x9ae00000 0x0 0x1900000>; + no-map; + }; + + mba_mem: memory@9c700000 { + reg = <0x0 0x9c700000 0x0 0x200000>; + no-map; + }; + }; +}; + &apps_rsc { pm7325-regulators { compatible = "qcom,pm7325-rpmh-regulators"; @@ -199,6 +284,23 @@ modem-init; }; +&pcie1 { + status = "okay"; + perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>; + + vddpe-3v3-supply = <&nvme_3v3_regulator>; + + pinctrl-names = "default"; + pinctrl-0 = <&pcie1_reset_n>, <&pcie1_wake_n>; +}; + +&pcie1_phy { + status = "okay"; + + vdda-phy-supply = <&vreg_l10c_0p8>; + vdda-pll-supply = <&vreg_l6b_1p2>; +}; + &pmk8350_vadc { pmk8350_die_temp { reg = <PMK8350_ADC7_DIE_TEMP>; @@ -207,10 +309,39 @@ }; }; +&qfprom { + vcc-supply = <&vreg_l1c_1p8>; +}; + +&qspi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <37500000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + }; +}; + &qupv3_id_0 { status = "okay"; }; +&qupv3_id_1 { + status = "okay"; +}; + +&remoteproc_mpss { + status = "okay"; + compatible = "qcom,sc7280-mss-pil"; + iommus = <&apps_smmu 0x124 0x0>, <&apps_smmu 0x488 0x7>; + memory-region = <&mba_mem &mpss_mem>; +}; + &sdhc_1 { status = "okay"; @@ -240,6 +371,7 @@ }; &uart5 { + compatible = "qcom,geni-debug-uart"; status = "okay"; }; @@ -282,20 +414,146 @@ vdda18-supply = <&vreg_l1c_1p8>; }; +&uart7 { + status = "okay"; + + /delete-property/interrupts; + interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>, + <&tlmm 31 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default", "sleep"; + pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>; +}; + /* PINCTRL - additions to nodes defined in sc7280.dtsi */ -&qup_uart5_default { - tx { - pins = "gpio46"; - drive-strength = <2>; +&pm7325_gpios { + key_vol_up_default: key-vol-up-default { + pins = "gpio6"; + function = "normal"; + input-enable; + bias-pull-up; + power-source = <0>; + qcom,drive-strength = <3>; + }; +}; + +&qspi_cs0 { + bias-disable; +}; + +&qspi_clk { + bias-disable; +}; + +&qspi_data01 { + /* High-Z when no transfers; nice to park the lines */ + bias-pull-up; +}; + +&qup_uart5_tx { + drive-strength = <2>; + bias-disable; +}; + +&qup_uart5_rx { + drive-strength = <2>; + bias-pull-up; +}; + +&qup_uart7_cts { + /* + * Configure a pull-down on CTS to match the pull of + * the Bluetooth module. + */ + bias-pull-down; +}; + +&qup_uart7_rts { + /* We'll drive RTS, so no pull */ + drive-strength = <2>; + bias-disable; +}; + +&qup_uart7_tx { + /* We'll drive TX, so no pull */ + drive-strength = <2>; + bias-disable; +}; + +&qup_uart7_rx { + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module is + * in tri-state (module powered off or not driving the + * signal yet). + */ + bias-pull-up; +}; + +&tlmm { + nvme_pwren: nvme-pwren { + function = "gpio"; + }; + + pcie1_reset_n: pcie1-reset-n { + pins = "gpio2"; + function = "gpio"; + + drive-strength = <16>; + output-low; bias-disable; }; - rx { - pins = "gpio47"; + pcie1_wake_n: pcie1-wake-n { + pins = "gpio3"; + function = "gpio"; + drive-strength = <2>; bias-pull-up; }; + + qup_uart7_sleep_cts: qup-uart7-sleep-cts { + pins = "gpio28"; + function = "gpio"; + /* + * Configure a pull-down on CTS to match the pull of + * the Bluetooth module. + */ + bias-pull-down; + }; + + qup_uart7_sleep_rts: qup-uart7-sleep-rts { + pins = "gpio29"; + function = "gpio"; + /* + * Configure pull-down on RTS. As RTS is active low + * signal, pull it low to indicate the BT SoC that it + * can wakeup the system anytime from suspend state by + * pulling RX low (by sending wakeup bytes). + */ + bias-pull-down; + }; + + qup_uart7_sleep_tx: qup-uart7-sleep-tx { + pins = "gpio30"; + function = "gpio"; + /* + * Configure pull-up on TX when it isn't actively driven + * to prevent BT SoC from receiving garbage during sleep. + */ + bias-pull-up; + }; + + qup_uart7_sleep_rx: qup-uart7-sleep-rx { + pins = "gpio31"; + function = "gpio"; + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module + * is floating which may cause spurious wakeups. + */ + bias-pull-up; + }; }; &sdc1_on { @@ -336,6 +594,7 @@ }; sd-cd { + pins = "gpio91"; bias-pull-up; }; }; |