diff options
Diffstat (limited to 'dts/src/arm64/rockchip/rk3399-puma.dtsi')
| -rw-r--r-- | dts/src/arm64/rockchip/rk3399-puma.dtsi | 108 |
1 files changed, 53 insertions, 55 deletions
diff --git a/dts/src/arm64/rockchip/rk3399-puma.dtsi b/dts/src/arm64/rockchip/rk3399-puma.dtsi index 07694b196f..c08e69391c 100644 --- a/dts/src/arm64/rockchip/rk3399-puma.dtsi +++ b/dts/src/arm64/rockchip/rk3399-puma.dtsi @@ -8,12 +8,17 @@ #include "rk3399-opp.dtsi" / { + aliases { + ethernet0 = &gmac; + mmc0 = &sdhci; + }; + leds { compatible = "gpio-leds"; pinctrl-names = "default"; - pinctrl-0 = <&led_pin_module>; + pinctrl-0 = <&module_led_pin>; - module-led { + module_led: led-0 { label = "module_led"; gpios = <&gpio2 RK_PD1 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; @@ -21,55 +26,11 @@ }; }; - /* - * Overwrite the opp-table for CPUB as this board uses a different - * regulator (FAN53555) that only allows 10mV steps and therefore - * can't reach the operation point target voltages from rk3399-opp.dtsi - */ - /delete-node/ opp-table1; - cluster1_opp: opp-table1 { - compatible = "operating-points-v2"; - opp-shared; - - opp00 { - opp-hz = /bits/ 64 <408000000>; - opp-microvolt = <800000>; - clock-latency-ns = <40000>; - }; - opp01 { - opp-hz = /bits/ 64 <600000000>; - opp-microvolt = <800000>; - }; - opp02 { - opp-hz = /bits/ 64 <816000000>; - opp-microvolt = <830000>; - opp-suspend; - }; - opp03 { - opp-hz = /bits/ 64 <1008000000>; - opp-microvolt = <880000>; - }; - opp04 { - opp-hz = /bits/ 64 <1200000000>; - opp-microvolt = <950000>; - }; - opp05 { - opp-hz = /bits/ 64 <1416000000>; - opp-microvolt = <1030000>; - }; - opp06 { - opp-hz = /bits/ 64 <1608000000>; - opp-microvolt = <1100000>; - }; - opp07 { - opp-hz = /bits/ 64 <1800000000>; - opp-microvolt = <1200000>; - }; - opp08 { - opp-hz = /bits/ 64 <1992000000>; - opp-microvolt = <1230000>; - turbo-mode; - }; + extcon_usb3: extcon-usb3 { + compatible = "linux,extcon-usb-gpio"; + id-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb3_id>; }; clkin_gmac: external-gmac-clock { @@ -101,8 +62,7 @@ vcc5v0_host: vcc5v0-host-regulator { compatible = "regulator-fixed"; - gpio = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>; - enable-active-low; + gpio = <&gpio4 RK_PA3 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; pinctrl-0 = <&vcc5v0_host_en>; regulator-name = "vcc5v0_host"; @@ -118,6 +78,17 @@ regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; }; + + vdd_log: vdd-log { + compatible = "pwm-regulator"; + pwms = <&pwm2 0 25000 1>; + pwm-supply = <&vcc5v0_sys>; + regulator-name = "vdd_log"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + regulator-boot-on; + }; }; &cpu_b0 { @@ -149,6 +120,20 @@ drive-impedance-ohm = <33>; }; +&gpio0 { + /* + * The BIOS_DISABLE hog is a feedback pin for the actual status of the + * signal. This usually represents the state of a switch on the baseboard. + * The pin has a 10k pull-up resistor connected, so no pull-up setting is needed. + */ + bios-disable-hog { + gpios = <RK_PB0 GPIO_ACTIVE_HIGH>; + gpio-hog; + input; + line-name = "bios_disable"; + }; +}; + &gmac { assigned-clocks = <&cru SCLK_RMII_SRC>; assigned-clock-parents = <&clkin_gmac>; @@ -157,7 +142,7 @@ phy-mode = "rgmii"; pinctrl-names = "default"; pinctrl-0 = <&rgmii_pins>; - snps,reset-gpio = <&gpio3 RK_PC0 GPIO_ACTIVE_HIGH>; + snps,reset-gpio = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>; snps,reset-active-low; snps,reset-delays-us = <0 10000 50000>; tx_delay = <0x10>; @@ -450,7 +435,7 @@ }; leds { - led_pin_module: led-module-gpio { + module_led_pin: module-led-pin { rockchip,pins = <2 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>; }; @@ -469,9 +454,22 @@ <4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>; }; }; + + usb3 { + usb3_id: usb3-id { + rockchip,pins = + <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; }; &sdhci { + /* + * Signal integrity isn't great at 200MHz but 100MHz has proven stable + * enough. + */ + max-frequency = <100000000>; + bus-width = <8>; mmc-hs400-1_8v; mmc-hs400-enhanced-strobe; |