diff options
Diffstat (limited to 'include/linux/clk')
| -rw-r--r-- | include/linux/clk/analogbits-wrpll-cln28hpc.h | 79 | ||||
| -rw-r--r-- | include/linux/clk/at91_pmc.h | 118 |
2 files changed, 183 insertions, 14 deletions
diff --git a/include/linux/clk/analogbits-wrpll-cln28hpc.h b/include/linux/clk/analogbits-wrpll-cln28hpc.h new file mode 100644 index 0000000000..03279097e1 --- /dev/null +++ b/include/linux/clk/analogbits-wrpll-cln28hpc.h @@ -0,0 +1,79 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2018-2019 SiFive, Inc. + * Wesley Terpstra + * Paul Walmsley + */ + +#ifndef __LINUX_CLK_ANALOGBITS_WRPLL_CLN28HPC_H +#define __LINUX_CLK_ANALOGBITS_WRPLL_CLN28HPC_H + +#include <linux/types.h> + +/* DIVQ_VALUES: number of valid DIVQ values */ +#define DIVQ_VALUES 6 + +/* + * Bit definitions for struct wrpll_cfg.flags + * + * WRPLL_FLAGS_BYPASS_FLAG: if set, the PLL is either in bypass, or should be + * programmed to enter bypass + * WRPLL_FLAGS_RESET_FLAG: if set, the PLL is in reset + * WRPLL_FLAGS_INT_FEEDBACK_FLAG: if set, the PLL is configured for internal + * feedback mode + * WRPLL_FLAGS_EXT_FEEDBACK_FLAG: if set, the PLL is configured for external + * feedback mode (not yet supported by this driver) + */ +#define WRPLL_FLAGS_BYPASS_SHIFT 0 +#define WRPLL_FLAGS_BYPASS_MASK BIT(WRPLL_FLAGS_BYPASS_SHIFT) +#define WRPLL_FLAGS_RESET_SHIFT 1 +#define WRPLL_FLAGS_RESET_MASK BIT(WRPLL_FLAGS_RESET_SHIFT) +#define WRPLL_FLAGS_INT_FEEDBACK_SHIFT 2 +#define WRPLL_FLAGS_INT_FEEDBACK_MASK BIT(WRPLL_FLAGS_INT_FEEDBACK_SHIFT) +#define WRPLL_FLAGS_EXT_FEEDBACK_SHIFT 3 +#define WRPLL_FLAGS_EXT_FEEDBACK_MASK BIT(WRPLL_FLAGS_EXT_FEEDBACK_SHIFT) + +/** + * struct wrpll_cfg - WRPLL configuration values + * @divr: reference divider value (6 bits), as presented to the PLL signals + * @divf: feedback divider value (9 bits), as presented to the PLL signals + * @divq: output divider value (3 bits), as presented to the PLL signals + * @flags: PLL configuration flags. See above for more information + * @range: PLL loop filter range. See below for more information + * @output_rate_cache: cached output rates, swept across DIVQ + * @parent_rate: PLL refclk rate for which values are valid + * @max_r: maximum possible R divider value, given @parent_rate + * @init_r: initial R divider value to start the search from + * + * @divr, @divq, @divq, @range represent what the PLL expects to see + * on its input signals. Thus @divr and @divf are the actual divisors + * minus one. @divq is a power-of-two divider; for example, 1 = + * divide-by-2 and 6 = divide-by-64. 0 is an invalid @divq value. + * + * When initially passing a struct wrpll_cfg record, the + * record should be zero-initialized with the exception of the @flags + * field. The only flag bits that need to be set are either + * WRPLL_FLAGS_INT_FEEDBACK or WRPLL_FLAGS_EXT_FEEDBACK. + */ +struct wrpll_cfg { + u8 divr; + u8 divq; + u8 range; + u8 flags; + u16 divf; +/* private: */ + u32 output_rate_cache[DIVQ_VALUES]; + unsigned long parent_rate; + u8 max_r; + u8 init_r; +}; + +int wrpll_configure_for_rate(struct wrpll_cfg *c, u32 target_rate, + unsigned long parent_rate); + +unsigned int wrpll_calc_max_lock_us(const struct wrpll_cfg *c); + +unsigned long wrpll_calc_output_rate(const struct wrpll_cfg *c, + unsigned long parent_rate); + +#endif /* __LINUX_CLK_ANALOGBITS_WRPLL_CLN28HPC_H */ diff --git a/include/linux/clk/at91_pmc.h b/include/linux/clk/at91_pmc.h index 17f413bbbe..7af499bdbe 100644 --- a/include/linux/clk/at91_pmc.h +++ b/include/linux/clk/at91_pmc.h @@ -1,3 +1,4 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ /* * include/linux/clk/at91_pmc.h * @@ -6,16 +7,16 @@ * * Power Management Controller (PMC) - System peripherals registers. * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. */ #ifndef AT91_PMC_H #define AT91_PMC_H +#include <linux/bits.h> + +#define AT91_PMC_V1 (1) /* PMC version 1 */ +#define AT91_PMC_V2 (2) /* PMC version 2 [SAM9X60] */ + #define AT91_PMC_SCER 0x00 /* System Clock Enable Register */ #define AT91_PMC_SCDR 0x04 /* System Clock Disable Register */ @@ -34,21 +35,42 @@ #define AT91_PMC_HCK0 (1 << 16) /* AHB Clock (USB host) [AT91SAM9261 only] */ #define AT91_PMC_HCK1 (1 << 17) /* AHB Clock (LCD) [AT91SAM9261 only] */ +#define AT91_PMC_PLL_CTRL0 0x0C /* PLL Control Register 0 [for SAM9X60] */ +#define AT91_PMC_PLL_CTRL0_ENPLL (1 << 28) /* Enable PLL */ +#define AT91_PMC_PLL_CTRL0_ENPLLCK (1 << 29) /* Enable PLL clock for PMC */ +#define AT91_PMC_PLL_CTRL0_ENLOCK (1 << 31) /* Enable PLL lock */ + +#define AT91_PMC_PLL_CTRL1 0x10 /* PLL Control Register 1 [for SAM9X60] */ + #define AT91_PMC_PCER 0x10 /* Peripheral Clock Enable Register */ #define AT91_PMC_PCDR 0x14 /* Peripheral Clock Disable Register */ #define AT91_PMC_PCSR 0x18 /* Peripheral Clock Status Register */ +#define AT91_PMC_PLL_ACR 0x18 /* PLL Analog Control Register [for SAM9X60] */ +#define AT91_PMC_PLL_ACR_DEFAULT_UPLL UL(0x12020010) /* Default PLL ACR value for UPLL */ +#define AT91_PMC_PLL_ACR_DEFAULT_PLLA UL(0x00020010) /* Default PLL ACR value for PLLA */ +#define AT91_PMC_PLL_ACR_UTMIVR (1 << 12) /* UPLL Voltage regulator Control */ +#define AT91_PMC_PLL_ACR_UTMIBG (1 << 13) /* UPLL Bandgap Control */ + #define AT91_CKGR_UCKR 0x1C /* UTMI Clock Register [some SAM9] */ #define AT91_PMC_UPLLEN (1 << 16) /* UTMI PLL Enable */ #define AT91_PMC_UPLLCOUNT (0xf << 20) /* UTMI PLL Start-up Time */ #define AT91_PMC_BIASEN (1 << 24) /* UTMI BIAS Enable */ #define AT91_PMC_BIASCOUNT (0xf << 28) /* UTMI BIAS Start-up Time */ +#define AT91_PMC_PLL_UPDT 0x1C /* PMC PLL update register [for SAM9X60] */ +#define AT91_PMC_PLL_UPDT_UPDATE (1 << 8) /* Update PLL settings */ +#define AT91_PMC_PLL_UPDT_ID (1 << 0) /* PLL ID */ +#define AT91_PMC_PLL_UPDT_ID_MSK (0xf) /* PLL ID mask */ +#define AT91_PMC_PLL_UPDT_STUPTIM (0xff << 16) /* Startup time */ + #define AT91_CKGR_MOR 0x20 /* Main Oscillator Register [not on SAM9RL] */ #define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */ #define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass */ +#define AT91_PMC_WAITMODE (1 << 2) /* Wait Mode Command */ #define AT91_PMC_MOSCRCEN (1 << 3) /* Main On-Chip RC Oscillator Enable [some SAM9] */ #define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */ +#define AT91_PMC_KEY_MASK (0xff << 16) #define AT91_PMC_KEY (0x37 << 16) /* MOR Writing Key */ #define AT91_PMC_MOSCSEL (1 << 24) /* Main Oscillator Selection [some SAM9] */ #define AT91_PMC_CFDEN (1 << 25) /* Clock Failure Detector Enable [some SAM9] */ @@ -58,6 +80,10 @@ #define AT91_PMC_MAINRDY (1 << 16) /* Main Clock Ready */ #define AT91_CKGR_PLLAR 0x28 /* PLL A Register */ + +#define AT91_PMC_RATIO 0x2c /* Processor clock ratio register [SAMA7G5 only] */ +#define AT91_PMC_RATIO_RATIO (0xf) /* CPU clock ratio. */ + #define AT91_CKGR_PLLBR 0x2c /* PLL B Register */ #define AT91_PMC_DIV (0xff << 0) /* Divider */ #define AT91_PMC_PLLCOUNT (0x3f << 8) /* PLL Counter */ @@ -72,6 +98,8 @@ #define AT91_PMC_USBDIV_4 (2 << 28) #define AT91_PMC_USB96M (1 << 28) /* Divider by 2 Enable (PLLB only) */ +#define AT91_PMC_CPU_CKR 0x28 /* CPU Clock Register */ + #define AT91_PMC_MCKR 0x30 /* Master Clock Register */ #define AT91_PMC_CSS (3 << 0) /* Master Clock Selection */ #define AT91_PMC_CSS_SLOW (0 << 0) @@ -115,6 +143,34 @@ #define AT91_PMC_PLLADIV2_ON (1 << 12) #define AT91_PMC_H32MXDIV BIT(24) +#define AT91_PMC_MCR_V2 0x30 /* Master Clock Register [SAMA7G5 only] */ +#define AT91_PMC_MCR_V2_ID_MSK (0xF) +#define AT91_PMC_MCR_V2_ID(_id) ((_id) & AT91_PMC_MCR_V2_ID_MSK) +#define AT91_PMC_MCR_V2_CMD (1 << 7) +#define AT91_PMC_MCR_V2_DIV (7 << 8) +#define AT91_PMC_MCR_V2_DIV1 (0 << 8) +#define AT91_PMC_MCR_V2_DIV2 (1 << 8) +#define AT91_PMC_MCR_V2_DIV4 (2 << 8) +#define AT91_PMC_MCR_V2_DIV8 (3 << 8) +#define AT91_PMC_MCR_V2_DIV16 (4 << 8) +#define AT91_PMC_MCR_V2_DIV32 (5 << 8) +#define AT91_PMC_MCR_V2_DIV64 (6 << 8) +#define AT91_PMC_MCR_V2_DIV3 (7 << 8) +#define AT91_PMC_MCR_V2_CSS (0x1F << 16) +#define AT91_PMC_MCR_V2_CSS_MD_SLCK (0 << 16) +#define AT91_PMC_MCR_V2_CSS_TD_SLCK (1 << 16) +#define AT91_PMC_MCR_V2_CSS_MAINCK (2 << 16) +#define AT91_PMC_MCR_V2_CSS_MCK0 (3 << 16) +#define AT91_PMC_MCR_V2_CSS_SYSPLL (5 << 16) +#define AT91_PMC_MCR_V2_CSS_DDRPLL (6 << 16) +#define AT91_PMC_MCR_V2_CSS_IMGPLL (7 << 16) +#define AT91_PMC_MCR_V2_CSS_BAUDPLL (8 << 16) +#define AT91_PMC_MCR_V2_CSS_AUDIOPLL (9 << 16) +#define AT91_PMC_MCR_V2_CSS_ETHPLL (10 << 16) +#define AT91_PMC_MCR_V2_EN (1 << 28) + +#define AT91_PMC_XTALF 0x34 /* Main XTAL Frequency Register [SAMA7G5 only] */ + #define AT91_PMC_USB 0x38 /* USB Clock Register [some SAM9 only] */ #define AT91_PMC_USBS (0x1 << 0) /* USB OHCI Input clock selection */ #define AT91_PMC_USBS_PLLA (0 << 0) @@ -153,8 +209,23 @@ #define AT91_PMC_MOSCRCS (1 << 17) /* Main On-Chip RC [some SAM9] */ #define AT91_PMC_CFDEV (1 << 18) /* Clock Failure Detector Event [some SAM9] */ #define AT91_PMC_GCKRDY (1 << 24) /* Generated Clocks */ +#define AT91_PMC_MCKXRDY (1 << 26) /* Master Clock x [x=1..4] Ready Status */ #define AT91_PMC_IMR 0x6c /* Interrupt Mask Register */ +#define AT91_PMC_FSMR 0x70 /* Fast Startup Mode Register */ +#define AT91_PMC_FSTT(n) BIT(n) +#define AT91_PMC_RTTAL BIT(16) +#define AT91_PMC_RTCAL BIT(17) /* RTC Alarm Enable */ +#define AT91_PMC_USBAL BIT(18) /* USB Resume Enable */ +#define AT91_PMC_SDMMC_CD BIT(19) /* SDMMC Card Detect Enable */ +#define AT91_PMC_LPM BIT(20) /* Low-power Mode */ +#define AT91_PMC_RXLP_MCE BIT(24) /* Backup UART Receive Enable */ +#define AT91_PMC_ACC_CE BIT(25) /* ACC Enable */ + +#define AT91_PMC_FSPR 0x74 /* Fast Startup Polarity Reg */ + +#define AT91_PMC_FS_INPUT_MASK 0x7ff + #define AT91_PMC_PLLICPR 0x80 /* PLL Charge Pump Current Register */ #define AT91_PMC_PROT 0xe4 /* Write Protect Mode Register [some SAM9] */ @@ -166,23 +237,42 @@ #define AT91_PMC_WPVS (0x1 << 0) /* Write Protect Violation Status */ #define AT91_PMC_WPVSRC (0xffff << 8) /* Write Protect Violation Source */ +#define AT91_PMC_PLL_ISR0 0xEC /* PLL Interrupt Status Register 0 [SAM9X60 only] */ + #define AT91_PMC_PCER1 0x100 /* Peripheral Clock Enable Register 1 [SAMA5 only]*/ #define AT91_PMC_PCDR1 0x104 /* Peripheral Clock Enable Register 1 */ #define AT91_PMC_PCSR1 0x108 /* Peripheral Clock Enable Register 1 */ #define AT91_PMC_PCR 0x10c /* Peripheral Control Register [some SAM9 and SAMA5] */ #define AT91_PMC_PCR_PID_MASK 0x3f -#define AT91_PMC_PCR_GCKCSS_OFFSET 8 -#define AT91_PMC_PCR_GCKCSS_MASK (0x7 << AT91_PMC_PCR_GCKCSS_OFFSET) -#define AT91_PMC_PCR_GCKCSS(n) ((n) << AT91_PMC_PCR_GCKCSS_OFFSET) /* GCK Clock Source Selection */ #define AT91_PMC_PCR_CMD (0x1 << 12) /* Command (read=0, write=1) */ -#define AT91_PMC_PCR_DIV_OFFSET 16 -#define AT91_PMC_PCR_DIV_MASK (0x3 << AT91_PMC_PCR_DIV_OFFSET) -#define AT91_PMC_PCR_DIV(n) ((n) << AT91_PMC_PCR_DIV_OFFSET) /* Divisor Value */ -#define AT91_PMC_PCR_GCKDIV_OFFSET 20 -#define AT91_PMC_PCR_GCKDIV_MASK (0xff << AT91_PMC_PCR_GCKDIV_OFFSET) -#define AT91_PMC_PCR_GCKDIV(n) ((n) << AT91_PMC_PCR_GCKDIV_OFFSET) /* Generated Clock Divisor Value */ +#define AT91_PMC_PCR_GCKDIV_MASK GENMASK(27, 20) #define AT91_PMC_PCR_EN (0x1 << 28) /* Enable */ #define AT91_PMC_PCR_GCKEN (0x1 << 29) /* GCK Enable */ +#define AT91_PMC_AUDIO_PLL0 0x14c +#define AT91_PMC_AUDIO_PLL_PLLEN (1 << 0) +#define AT91_PMC_AUDIO_PLL_PADEN (1 << 1) +#define AT91_PMC_AUDIO_PLL_PMCEN (1 << 2) +#define AT91_PMC_AUDIO_PLL_RESETN (1 << 3) +#define AT91_PMC_AUDIO_PLL_ND_OFFSET 8 +#define AT91_PMC_AUDIO_PLL_ND_MASK (0x7f << AT91_PMC_AUDIO_PLL_ND_OFFSET) +#define AT91_PMC_AUDIO_PLL_ND(n) ((n) << AT91_PMC_AUDIO_PLL_ND_OFFSET) +#define AT91_PMC_AUDIO_PLL_QDPMC_OFFSET 16 +#define AT91_PMC_AUDIO_PLL_QDPMC_MASK (0x7f << AT91_PMC_AUDIO_PLL_QDPMC_OFFSET) +#define AT91_PMC_AUDIO_PLL_QDPMC(n) ((n) << AT91_PMC_AUDIO_PLL_QDPMC_OFFSET) + +#define AT91_PMC_AUDIO_PLL1 0x150 +#define AT91_PMC_AUDIO_PLL_FRACR_MASK 0x3fffff +#define AT91_PMC_AUDIO_PLL_QDPAD_OFFSET 24 +#define AT91_PMC_AUDIO_PLL_QDPAD_MASK (0x7f << AT91_PMC_AUDIO_PLL_QDPAD_OFFSET) +#define AT91_PMC_AUDIO_PLL_QDPAD(n) ((n) << AT91_PMC_AUDIO_PLL_QDPAD_OFFSET) +#define AT91_PMC_AUDIO_PLL_QDPAD_DIV_OFFSET AT91_PMC_AUDIO_PLL_QDPAD_OFFSET +#define AT91_PMC_AUDIO_PLL_QDPAD_DIV_MASK (0x3 << AT91_PMC_AUDIO_PLL_QDPAD_DIV_OFFSET) +#define AT91_PMC_AUDIO_PLL_QDPAD_DIV(n) ((n) << AT91_PMC_AUDIO_PLL_QDPAD_DIV_OFFSET) +#define AT91_PMC_AUDIO_PLL_QDPAD_EXTDIV_OFFSET 26 +#define AT91_PMC_AUDIO_PLL_QDPAD_EXTDIV_MAX 0x1f +#define AT91_PMC_AUDIO_PLL_QDPAD_EXTDIV_MASK (AT91_PMC_AUDIO_PLL_QDPAD_EXTDIV_MAX << AT91_PMC_AUDIO_PLL_QDPAD_EXTDIV_OFFSET) +#define AT91_PMC_AUDIO_PLL_QDPAD_EXTDIV(n) ((n) << AT91_PMC_AUDIO_PLL_QDPAD_EXTDIV_OFFSET) + #endif |