1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
|
// SPDX-License-Identifier: GPL-2.0
#include <io.h>
#include <common.h>
#include <debug_ll.h>
#include <mach/imx/debug_ll.h>
#include <firmware.h>
#include <asm/mmu.h>
#include <asm/cache.h>
#include <asm/sections.h>
#include <asm/barebox-arm.h>
#include <asm/barebox-arm-head.h>
#include <pbl/i2c.h>
#include <pbl/pmic.h>
#include <linux/sizes.h>
#include <mach/imx/atf.h>
#include <mach/imx/xload.h>
#include <mach/imx/esdctl.h>
#include <mach/imx/generic.h>
#include <mach/imx/imx8mp-regs.h>
#include <mach/imx/iomux-mx8mp.h>
#include <mach/imx/imx8m-ccm-regs.h>
#include <mfd/pca9450.h>
#include <soc/imx8m/ddr.h>
#include <soc/fsl/fsl_udc.h>
extern char __dtb_z_imx8mp_var_dart_dt8mcustomboard_start[];
#define UART_PAD_CTRL MUX_PAD_CTRL(MX8MP_PAD_CTL_DSE6 | MX8MP_PAD_CTL_FSEL)
#define I2C_PAD_CTRL MUX_PAD_CTRL(MX8MP_PAD_CTL_DSE6 | \
MX8MP_PAD_CTL_HYS | \
MX8MP_PAD_CTL_PUE | \
MX8MP_PAD_CTL_PE)
static void setup_uart(void)
{
void __iomem *uart = IOMEM(MX8M_UART1_BASE_ADDR);
imx8m_early_setup_uart_clock();
imx8mp_setup_pad(MX8MP_PAD_UART1_TXD__UART1_DCE_TX | UART_PAD_CTRL);
imx8mp_setup_pad(MX8MP_PAD_UART1_RXD__UART1_DCE_RX | UART_PAD_CTRL);
imx8m_uart_setup(uart);
pbl_set_putc(imx_uart_putc, uart);
putc_ll('>');
}
static struct pmic_config pca9450_cfg[] = {
/* BUCKxOUT_DVS0/1 control BUCK123 output */
{ PCA9450_BUCK123_DVS, 0x29 },
/*
* increase VDD_SOC to typical value 0.95V before first
* DRAM access, set DVS1 to 0.85v for suspend.
* Enable DVS control through PMIC_STBY_REQ and
* set B1_ENMODE=1 (ON by PMIC_ON_REQ=H)
*/
{ PCA9450_BUCK1OUT_DVS0, 0x1C },
{ PCA9450_BUCK1OUT_DVS1, 0x14 },
{ PCA9450_BUCK1CTRL, 0x59 },
/* set WDOG_B_CFG to cold reset */
{ PCA9450_RESET_CTRL, 0xA1 },
};
static void power_init_board(void)
{
struct pbl_i2c *i2c;
imx8mp_setup_pad(MX8MP_PAD_I2C1_SCL__I2C1_SCL | I2C_PAD_CTRL);
imx8mp_setup_pad(MX8MP_PAD_I2C1_SDA__I2C1_SDA | I2C_PAD_CTRL);
imx8m_ccgr_clock_enable(IMX8M_CCM_CCGR_I2C1);
i2c = imx8m_i2c_early_init(IOMEM(MX8MP_I2C1_BASE_ADDR));
pmic_configure(i2c, 0x25, pca9450_cfg, ARRAY_SIZE(pca9450_cfg));
}
extern struct dram_timing_info var_dart_imx8mp_dram_timing;
static void start_atf(void)
{
/*
* If we are in EL3 we are running for the first time and need to
* initialize the DRAM and run TF-A (BL31). The TF-A will then jump
* to DRAM in EL2.
*/
if (current_el() != 3)
return;
imx8mm_early_clock_init();
power_init_board();
imx8mp_ddr_init(&var_dart_imx8mp_dram_timing, DRAM_TYPE_LPDDR4);
imx8mp_load_and_start_image_via_tfa();
}
static __noreturn noinline void variscite_imx8mp_dart_cb_start(void)
{
setup_uart();
start_atf();
/*
* Standard entry we hit once we initialized both DDR and ATF
*/
imx8mp_barebox_entry(__dtb_z_imx8mp_var_dart_dt8mcustomboard_start);
}
/*
* Power-on execution flow of nxp_imx8mp_vardart_start() might not be
* obvious for a very first read, so here's, hopefully helpful,
* summary:
*
* 1. MaskROM uploads PBL into OCRAM and that's where this function is
* executed for the first time. At entry the exception level is EL3.
*
* 2. DDR is initialized and the image is loaded from storage into DRAM. The PBL
* part is copied from OCRAM to the TF-A return address in DRAM.
*
* 3. TF-A is executed and exits into the PBL code in DRAM. TF-A has taken us
* from EL3 to EL2.
*
* 4. Standard barebox boot flow continues
*/
ENTRY_FUNCTION(start_variscite_imx8mp_dart, r0, r1, r2)
{
imx8mp_cpu_lowlevel_init();
relocate_to_current_adr();
setup_c();
variscite_imx8mp_dart_cb_start();
}
|
