path: root/dts/Bindings/net/dsa/marvell,mv88e6xxx.yaml

# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Marvell MV88E6xxx DSA switch family

maintainers:
  - Andrew Lunn <andrew@lunn.ch>

description:
  The Marvell MV88E6xxx switch series has been produced and sold
  by Marvell since at least 2008. The switch has a few compatibles which
  just indicate the base address of the switch, then operating systems
  can investigate switch ID registers to find out which actual version
  of the switch it is dealing with.

properties:
  compatible:
    oneOf:
      - enum:
          - marvell,mv88e6085
          - marvell,mv88e6190
          - marvell,mv88e6250
        description: |
          marvell,mv88e6085: This switch uses base address 0x10.
            This switch and its siblings will be autodetected from
            ID registers found in the switch, so only "marvell,mv88e6085" should be
            specified. This includes the following list of MV88Exxxx switches:
            6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, 6171, 6172, 6175, 6176,
            6185, 6240, 6320, 6321, 6341, 6350, 6351, 6352
          marvell,mv88e6190: This switch uses base address 0x00.
            This switch and its siblings will be autodetected from
            ID registers found in the switch, so only "marvell,mv88e6190" should be
            specified. This includes the following list of MV88Exxxx switches:
            6190, 6190X, 6191, 6290, 6361, 6390, 6390X
          marvell,mv88e6250: This switch uses base address 0x08 or 0x18.
            This switch and its siblings will be autodetected from
            ID registers found in the switch, so only "marvell,mv88e6250" should be
            specified. This includes the following list of MV88Exxxx switches:
            6220, 6250
      - items:
          - const: marvell,turris-mox-mv88e6085
          - const: marvell,mv88e6085
      - items:
          - const: marvell,turris-mox-mv88e6190
          - const: marvell,mv88e6190

  reg:
    maxItems: 1

  eeprom-length:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: Set to the length of an EEPROM connected to the switch. Must be
      set if the switch can not detect the presence and/or size of a connected
      EEPROM, otherwise optional.

  reset-gpios:
    description:
      GPIO to be used to reset the whole device
    maxItems: 1

  interrupts:
    description: The switch provides an external interrupt line, but it is
      not always used by target systems.
    maxItems: 1

  interrupt-controller:
    description: The switch has an internal interrupt controller used by
      the different sub-blocks.

  '#interrupt-cells':
    description: The internal interrupt controller only supports triggering
      on active high level interrupts so the second cell must alway be set to
      IRQ_TYPE_LEVEL_HIGH.
    const: 2

  mdio:
    $ref: /schemas/net/mdio.yaml#
    unevaluatedProperties: false
    description: Marvell MV88E6xxx switches have an varying combination of
      internal and external MDIO buses, in some cases a combined bus that
      can be used both internally and externally. This node is for the
      primary bus, used internally and sometimes also externally.

  mdio-external:
    $ref: /schemas/net/mdio.yaml#
    unevaluatedProperties: false
    description: Marvell MV88E6xxx switches that have a separate external
      MDIO bus use this port to access external components on the MDIO bus.

    properties:
      compatible:
        const: marvell,mv88e6xxx-mdio-external

    required:
      - compatible

allOf:
  - $ref: dsa.yaml#/$defs/ethernet-ports

required:
  - compatible
  - reg

unevaluatedProperties: false

examples:
  - |
    #include <dt-bindings/gpio/gpio.h>
    mdio {
        #address-cells = <1>;
        #size-cells = <0>;

        ethernet-switch@0 {
            compatible = "marvell,mv88e6085";
            reg = <0>;
            reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;

            mdio {
                #address-cells = <1>;
                #size-cells = <0>;

                sw_phy0: ethernet-phy@0 {
                    reg = <0x0>;
                };

                sw_phy1: ethernet-phy@1 {
                    reg = <0x1>;
                };

                sw_phy2: ethernet-phy@2 {
                    reg = <0x2>;
                };

                sw_phy3: ethernet-phy@3 {
                    reg = <0x3>;
                };
            };

            ethernet-ports {
                #address-cells = <1>;
                #size-cells = <0>;

                ethernet-port@0 {
                    reg = <0>;
                    label = "lan4";
                    phy-handle = <&sw_phy0>;
                    phy-mode = "internal";
                };

                ethernet-port@1 {
                    reg = <1>;
                    label = "lan3";
                    phy-handle = <&sw_phy1>;
                    phy-mode = "internal";
                };

                ethernet-port@2 {
                    reg = <2>;
                    label = "lan2";
                    phy-handle = <&sw_phy2>;
                    phy-mode = "internal";
                };

                ethernet-port@3 {
                    reg = <3>;
                    label = "lan1";
                    phy-handle = <&sw_phy3>;
                    phy-mode = "internal";
                };

                ethernet-port@5 {
                    reg = <5>;
                    ethernet = <&fec>;
                    phy-mode = "rgmii-id";

                    fixed-link {
                        speed = <1000>;
                        full-duplex;
                    };
                };
            };
        };
    };
  - |
    #include <dt-bindings/interrupt-controller/irq.h>
    mdio {
        #address-cells = <1>;
        #size-cells = <0>;

        ethernet-switch@0 {
            compatible = "marvell,mv88e6190";
            #interrupt-cells = <2>;
            interrupt-controller;
            interrupt-parent = <&gpio1>;
            interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
            pinctrl-0 = <&switch_interrupt_pins>;
            pinctrl-names = "default";
            reg = <0>;

            mdio {
                #address-cells = <1>;
                #size-cells = <0>;

                switch0phy1: ethernet-phy@1 {
                    reg = <0x1>;
                };

                switch0phy2: ethernet-phy@2 {
                    reg = <0x2>;
                };

                switch0phy3: ethernet-phy@3 {
                    reg = <0x3>;
                };

                switch0phy4: ethernet-phy@4 {
                    reg = <0x4>;
                };

                switch0phy5: ethernet-phy@5 {
                    reg = <0x5>;
                };

                switch0phy6: ethernet-phy@6 {
                    reg = <0x6>;
                };

                switch0phy7: ethernet-phy@7 {
                    reg = <0x7>;
                };

                switch0phy8: ethernet-phy@8 {
                    reg = <0x8>;
                };
            };

            mdio-external {
                compatible = "marvell,mv88e6xxx-mdio-external";
                #address-cells = <1>;
                #size-cells = <0>;

                phy1: ethernet-phy@b {
                    reg = <0xb>;
                    compatible = "ethernet-phy-ieee802.3-c45";
                };

                phy2: ethernet-phy@c {
                    reg = <0xc>;
                    compatible = "ethernet-phy-ieee802.3-c45";
                };
            };

            ethernet-ports {
                #address-cells = <1>;
                #size-cells = <0>;

                ethernet-port@0 {
                    ethernet = <&eth0>;
                    phy-mode = "rgmii";
                    reg = <0>;

                    fixed-link {
                        full-duplex;
                        pause;
                        speed = <1000>;
                    };
                };

                ethernet-port@1 {
                    label = "lan1";
                    phy-handle = <&switch0phy1>;
                    reg = <1>;
                };

                ethernet-port@2 {
                    label = "lan2";
                    phy-handle = <&switch0phy2>;
                    reg = <2>;
                };

                ethernet-port@3 {
                    label = "lan3";
                    phy-handle = <&switch0phy3>;
                    reg = <3>;
                };

                ethernet-port@4 {
                    label = "lan4";
                    phy-handle = <&switch0phy4>;
                    reg = <4>;
                };

                ethernet-port@5 {
                    label = "lan5";
                    phy-handle = <&switch0phy5>;
                    reg = <5>;
                };

                ethernet-port@6 {
                    label = "lan6";
                    phy-handle = <&switch0phy6>;
                    reg = <6>;
                };

                ethernet-port@7 {
                    label = "lan7";
                    phy-handle = <&switch0phy7>;
                    reg = <7>;
                };

                ethernet-port@8 {
                    label = "lan8";
                    phy-handle = <&switch0phy8>;
                    reg = <8>;
                };

                ethernet-port@9 {
                    /* 88X3310P external phy */
                    label = "lan9";
                    phy-handle = <&phy1>;
                    phy-mode = "xaui";
                    reg = <9>;
                };

                ethernet-port@a {
                    /* 88X3310P external phy */
                    label = "lan10";
                    phy-handle = <&phy2>;
                    phy-mode = "xaui";
                    reg = <0xa>;
                };
            };
        };
    };