Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:

 1) Add Maglev hashing scheduler to IPVS, from Inju Song.

 2) Lots of new TC subsystem tests from Roman Mashak.

 3) Add TCP zero copy receive and fix delayed acks and autotuning with
    SO_RCVLOWAT, from Eric Dumazet.

 4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
    Brouer.

 5) Add ttl inherit support to vxlan, from Hangbin Liu.

 6) Properly separate ipv6 routes into their logically independant
    components. fib6_info for the routing table, and fib6_nh for sets of
    nexthops, which thus can be shared. From David Ahern.

 7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
    messages from XDP programs. From Nikita V. Shirokov.

 8) Lots of long overdue cleanups to the r8169 driver, from Heiner
    Kallweit.

 9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.

10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.

11) Plumb extack down into fib_rules, from Roopa Prabhu.

12) Add Flower classifier offload support to igb, from Vinicius Costa
    Gomes.

13) Add UDP GSO support, from Willem de Bruijn.

14) Add documentation for eBPF helpers, from Quentin Monnet.

15) Add TLS tx offload to mlx5, from Ilya Lesokhin.

16) Allow applications to be given the number of bytes available to read
    on a socket via a control message returned from recvmsg(), from
    Soheil Hassas Yeganeh.

17) Add x86_32 eBPF JIT compiler, from Wang YanQing.

18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
    From Björn Töpel.

19) Remove indirect load support from all of the BPF JITs and handle
    these operations in the verifier by translating them into native BPF
    instead. From Daniel Borkmann.

20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.

21) Allow XDP programs to do lookups in the main kernel routing tables
    for forwarding. From David Ahern.

22) Allow drivers to store hardware state into an ELF section of kernel
    dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.

23) Various RACK and loss detection improvements in TCP, from Yuchung
    Cheng.

24) Add TCP SACK compression, from Eric Dumazet.

25) Add User Mode Helper support and basic bpfilter infrastructure, from
    Alexei Starovoitov.

26) Support ports and protocol values in RTM_GETROUTE, from Roopa
    Prabhu.

27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
    Brouer.

28) Add lots of forwarding selftests, from Petr Machata.

29) Add generic network device failover driver, from Sridhar Samudrala.

* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
  strparser: Add __strp_unpause and use it in ktls.
  rxrpc: Fix terminal retransmission connection ID to include the channel
  net: hns3: Optimize PF CMDQ interrupt switching process
  net: hns3: Fix for VF mailbox receiving unknown message
  net: hns3: Fix for VF mailbox cannot receiving PF response
  bnx2x: use the right constant
  Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
  net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
  enic: fix UDP rss bits
  netdev-FAQ: clarify DaveM's position for stable backports
  rtnetlink: validate attributes in do_setlink()
  mlxsw: Add extack messages for port_{un, }split failures
  netdevsim: Add extack error message for devlink reload
  devlink: Add extack to reload and port_{un, }split operations
  net: metrics: add proper netlink validation
  ipmr: fix error path when ipmr_new_table fails
  ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
  net: hns3: remove unused hclgevf_cfg_func_mta_filter
  netfilter: provide udp*_lib_lookup for nf_tproxy
  qed*: Utilize FW 8.37.2.0
  ...

1 files changed, 177 insertions, 0 deletions

diff --git a/Documentation/networking/e100.rst b/Documentation/networking/e100.rst
new file mode 100644
index 0000000000000..d4d8370279254
--- /dev/null
+++ b/Documentation/networking/e100.rst
@@ -0,0 +1,177 @@
+Linux* Base Driver for the Intel(R) PRO/100 Family of Adapters
+==============================================================
+
+June 1, 2018
+
+Contents
+========
+
+- In This Release
+- Identifying Your Adapter
+- Building and Installation
+- Driver Configuration Parameters
+- Additional Configurations
+- Known Issues
+- Support
+
+
+In This Release
+===============
+
+This file describes the Linux* Base Driver for the Intel(R) PRO/100 Family of
+Adapters. This driver includes support for Itanium(R)2-based systems.
+
+For questions related to hardware requirements, refer to the documentation
+supplied with your Intel PRO/100 adapter.
+
+The following features are now available in supported kernels:
+ - Native VLANs
+ - Channel Bonding (teaming)
+ - SNMP
+
+Channel Bonding documentation can be found in the Linux kernel source:
+/Documentation/networking/bonding.txt
+
+
+Identifying Your Adapter
+========================
+
+For information on how to identify your adapter, and for the latest Intel
+network drivers, refer to the Intel Support website:
+http://www.intel.com/support
+
+Driver Configuration Parameters
+===============================
+
+The default value for each parameter is generally the recommended setting,
+unless otherwise noted.
+
+Rx Descriptors: Number of receive descriptors. A receive descriptor is a data
+   structure that describes a receive buffer and its attributes to the network
+   controller. The data in the descriptor is used by the controller to write
+   data from the controller to host memory. In the 3.x.x driver the valid range
+   for this parameter is 64-256. The default value is 256. This parameter can be
+   changed using the command::
+
+   ethtool -G eth? rx n
+
+   Where n is the number of desired Rx descriptors.
+
+Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data
+   structure that describes a transmit buffer and its attributes to the network
+   controller. The data in the descriptor is used by the controller to read
+   data from the host memory to the controller. In the 3.x.x driver the valid
+   range for this parameter is 64-256. The default value is 128. This parameter
+   can be changed using the command::
+
+   ethtool -G eth? tx n
+
+   Where n is the number of desired Tx descriptors.
+
+Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by
+   default. The ethtool utility can be used as follows to force speed/duplex.::
+
+   ethtool -s eth?  autoneg off speed {10|100} duplex {full|half}
+
+   NOTE: setting the speed/duplex to incorrect values will cause the link to
+   fail.
+
+Event Log Message Level:  The driver uses the message level flag to log events
+   to syslog. The message level can be set at driver load time. It can also be
+   set using the command::
+
+   ethtool -s eth? msglvl n
+
+
+Additional Configurations
+=========================
+
+  Configuring the Driver on Different Distributions
+  -------------------------------------------------
+
+  Configuring a network driver to load properly when the system is started is
+  distribution dependent. Typically, the configuration process involves adding
+  an alias line to /etc/modprobe.d/*.conf as well as editing other system
+  startup scripts and/or configuration files.  Many popular Linux
+  distributions ship with tools to make these changes for you. To learn the
+  proper way to configure a network device for your system, refer to your
+  distribution documentation.  If during this process you are asked for the
+  driver or module name, the name for the Linux Base Driver for the Intel
+  PRO/100 Family of Adapters is e100.
+
+  As an example, if you install the e100 driver for two PRO/100 adapters
+  (eth0 and eth1), add the following to a configuration file in /etc/modprobe.d/
+
+       alias eth0 e100
+       alias eth1 e100
+
+  Viewing Link Messages
+  ---------------------
+  In order to see link messages and other Intel driver information on your
+  console, you must set the dmesg level up to six. This can be done by
+  entering the following on the command line before loading the e100 driver::
+
+       dmesg -n 6
+
+  If you wish to see all messages issued by the driver, including debug
+  messages, set the dmesg level to eight.
+
+  NOTE: This setting is not saved across reboots.
+
+
+  ethtool
+  -------
+
+  The driver utilizes the ethtool interface for driver configuration and
+  diagnostics, as well as displaying statistical information.  The ethtool
+  version 1.6 or later is required for this functionality.
+
+  The latest release of ethtool can be found from
+  https://www.kernel.org/pub/software/network/ethtool/
+
+  Enabling Wake on LAN* (WoL)
+  ---------------------------
+  WoL is provided through the ethtool* utility.  For instructions on enabling
+  WoL with ethtool, refer to the ethtool man page.
+
+  WoL will be enabled on the system during the next shut down or reboot. For
+  this driver version, in order to enable WoL, the e100 driver must be
+  loaded when shutting down or rebooting the system.
+
+  NAPI
+  ----
+
+  NAPI (Rx polling mode) is supported in the e100 driver.
+
+  See https://wiki.linuxfoundation.org/networking/napi for more information
+  on NAPI.
+
+  Multiple Interfaces on Same Ethernet Broadcast Network
+  ------------------------------------------------------
+
+  Due to the default ARP behavior on Linux, it is not possible to have
+  one system on two IP networks in the same Ethernet broadcast domain
+  (non-partitioned switch) behave as expected. All Ethernet interfaces
+  will respond to IP traffic for any IP address assigned to the system.
+  This results in unbalanced receive traffic.
+
+  If you have multiple interfaces in a server, either turn on ARP
+  filtering by
+
+  (1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
+      (this only works if your kernel's version is higher than 2.4.5), or
+
+  (2) installing the interfaces in separate broadcast domains (either
+      in different switches or in a switch partitioned to VLANs).
+
+
+Support
+=======
+For general information, go to the Intel support website at:
+http://www.intel.com/support/
+
+or the Intel Wired Networking project hosted by Sourceforge at:
+http://sourceforge.net/projects/e1000
+If an issue is identified with the released source code on a supported kernel
+with a supported adapter, email the specific information related to the issue
+to e1000-devel@lists.sf.net.